Using Your Drill; Handy Hints; Cooling Down; Overload - Black & Decker KD574 User Manual

ENGLISH @ y P P @ @ P @ P P P P P P P P P @ @ P @ P @ P P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ P P P P P P P P P @ @ P @ P @ P P @ @ @ P @ @ @ P @ @ @ P @ @
P P P @ P @ @ @ y P P P P P P P P P @ @ P @ P @ P P P @ P P P @ P P P @ P P P @ P P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @
PP yy @@ PP @@ PP @@ PP PP PP PP PP PP PP PP PP @@ PP @@ @@ PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ @@ @@ @@ PP PP @@ PP @@ @@ @@

USING YOUR DRILL

PP PP PP yy PP @@ PP @@ @@ PP PP PP PP PP PP PP PP PP PP PP PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ @@ PP
@@ @@ @@ @@ @@ PP PP @@ PP @@ PP PP PP @@ @@ @@ @@ PP PP @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP PP @@ @@ PP @@ @@ @@ PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ @@ yy @@ PP @@
@@ @@ @@ @@ @@ @@ @@ @@ @@ PP PP @@ PP @@ PP @@ @@ @@ PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP @@ @@ @@ PP @@ PP @@ PP @@ PP @@ PP PP @@ PP PP @@ @@ PP @@ PP @@ PP @@ PP PP PP @@ @@ yy @@ PP @@ PP
your drill when operation is continuous, depress the on/
off switch or variable speed switch again and release.
While your drill is in operation, do not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.
• Set the correct drill speed.
• Always hold your drill using the handle and the
side handle.
• Always hold your drill at right-angles to your work.
8
Set the forward/
reverse switch to the
desired direction of
rotation. Never change
the setting of the
hammer switch, the
speed switch, the
torque speed control
or the forward/reverse
mode
when your drill is in
to the drill mode
operation.
• Set the forward/reverse switch to the correct direction.
• Never change the direction of rotation when your
drill is in operation.
To switch your
• After use, remove the drill bit and gently tap the side
drill on, depress
of the chuck with a soft-faced hammer to remove
the on/off switch
the dust. This will extend the life of the chuck.
or the variable
speed switch.

COOLING DOWN

Your drill stops
If your drill becomes too hot in use, set the speed
when the on/off
control to its highest setting and allow your drill to
switch or the
operate without load for 2 minutes.
variable speed

OVERLOAD

switch is released.
Never use excessive force when using your drill. Too
If continuous
much pressure can reduce the speed of your drill and
operation is
reduce its efficiency. This can result in an overload
required, depress
which can cause damage to the motor of your drill.
the lock-on button
while the on/off

EC DECLARATION OF CONFORMITY

switch or variable
We declare that units: KD574RE, KD574CRE, KD577RT,
speed switch is
KD577CRT conform to 89/392/EEC, 89/336/EEC, EN55014,
depressed. To stop
73/23/EEC, EN55104, EN50144
A weighted sound pressure 94dB (A)
A weighted sound power 107dB (A)
Hand/arm weighted vibration 10.85m/s
We declare that unit: KD1000 conforms to 89/392/EEC,
89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144
A weighted sound pressure 96dB (A)
Set the torque speed
A weighted sound power 109dB (A)
control to the correct
Hand/arm weighted vibration 9.4m/s
setting for the size
of screw and the
material.
Brian Cooke - Director of Engineering
Black & Decker Ltd, Spennymoor, County Durham
DL16 6JG United Kingdom
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
When drilling
wood and metal,
set the hammer
switch to the drill
mode
When drilling
masonry, set the
hammer switch
to the hammer
. When screwdriving, set the hammer switch
.
2
2
.