Handy Hints; Cooling Down - Black & Decker KD574 User Manual

P y @ P @ P P @ P P P P P P P @ P @ P P @ P P @ @ P P @ P P P @ P P P @ P P P @ P P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ @ @ P @
@ @ P @ P P P P @ P @ @ @ @ @ @ @ P P @ P @ P P @ P P P @ P P P @ P @ y @ @ @ @ @ @ @ @ @ P P @ P @ P @ @ P P P @ P P P @ P P P @ P P P @ P P @ @
@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP PP PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP PP PP @@ PP PP PP @@ PP yy
USING YOUR DRILL
@@ PP @@ yy PP @@ PP @@ @@ @@ @@ @@ @@ @@ PP @@ PP @@ @@ PP @@ @@ PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ @@ @@ @@ @@ @@ @@ @@ @@ PP PP @@ PP @@ PP @@ @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@
PP @@ @@ yy @@ PP PP PP PP PP PP PP PP PP PP PP @@ @@ PP @@ PP @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ PP PP PP @@ PP @@ PP @@ PP @@ PP @@ @@ PP @@ @@ PP @@ @@ @@ PP PP PP @@ PP @@ PP PP @@ PP @@
@@ PP PP @@ PP @@ PP @@ @@ @@ @@ @@ @@ @@ @@ PP @@ PP @@ @@ PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP yy
your drill when operation is continuous, depress the on/
off switch or variable speed switch again and release.
While your drill is in operation, do not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.
• Set the correct drill speed.
• Always hold your drill using the handle and the
side handle.
• Always hold your drill at right-angles to your work.
Set the forward/
reverse switch to the
desired direction of
rotation. Never change
the setting of the
hammer switch, the
speed switch, the
torque speed control
or the forward/reverse
when your drill is in
operation.
To switch your
drill on, depress
the on/off switch
or the variable
speed switch.
Your drill stops
when the on/off
switch or the
variable speed
switch is released.
If continuous
operation is
required, depress
the lock-on button
while the on/off
switch or variable
speed switch is
depressed. To stop
Set the torque speed
control to the correct
setting for the size
of screw and the
material.
When screwdriving, set the hammer switch to the drill
mode .
• Set the forward/reverse switch to the correct direction.
• Never change the direction of rotation when your
drill is in operation.
• After use, remove the drill bit and gently tap the side
of the chuck with a soft-faced hammer to remove
the dust. This will extend the life of the chuck.

COOLING DOWN

If your drill becomes too hot in use, set the speed
control to its highest setting and allow your drill to
operate without load for 2 minutes.
OVERLOAD
Never use excessive force when using your drill. Too
much pressure can reduce the speed of your drill and
reduce its efficiency. This can result in an overload
which can cause damage to the motor of your drill.
EC DECLARATION OF CONFORMITY
We declare that units: KD574RE, KD574CRE, KD577RT,
KD577CRT conform to 89/392/EEC, 89/336/EEC, EN55014,
73/23/EEC, EN55104, EN50144
A weighted sound pressure 94dB (A)
A weighted sound power 107dB (A)
Hand/arm weighted vibration 10.85m/s
We declare that unit KD1000 conforms to 89/392/EEC,
89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144
A weighted sound pressure 96dB (A)
A weighted sound power 109dB (A)
Hand/arm weighted vibration 9.4m/s
Brian Cooke - Director of Engineering
Black & Decker Ltd, Spennymoor, County Durham
DL16 6JG United Kingdom
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
ENGLISH
When drilling
wood and metal,
set the hammer
switch to the drill
mode .
When drilling
masonry, set the
hammer switch
to the hammer
mode .
2
2
23