Handy Hints; Cooling Down - Black & Decker KR540 Manual

ENGLISH
length of the screw you will fit. Tighten the side
CP Q R R S S
   y z | | @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C CP Q R R S S
   @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C @ A B B C CP Q R R S S
   @ A B B C @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
   CP Q R R S S
   @ A B B C CP Q R R S S
   CP Q R R S S
  
   @ A B B C @ A B B C CP Q R R S S
  
handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct accessory for the job.
setting of the hammer switch, the speed switch or
the forward/reverse when your drill is in operation.
PP PP yy yy @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ PP PP PP PP @@ @@ PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP @@ @@ @@ @@ PP PP PP PP PP PP @@ @@ PP PP PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ PP PP PP PP PP PP @@ @@
USING YOUR DRILL
PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP PP yy yy PP PP @@ @@ PP PP PP PP @@ @@ PP PP PP PP PP PP @@ @@ PP PP @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP @@ @@ @@ @@ @@ @@ PP PP PP PP @@ @@ @@ @@ PP PP PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ PP PP @@ @@ @@ @@ PP PP PP PP @@ @@ @@ @@ @@ @@ PP PP PP PP @@ @@ @@ @@ PP PP
when operation is continuous, depress the switch
again and release. While your drill is in operation, do
not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver
bit.
• Always hold your drill using the handle and the
side handle.
24
KR540-600 ML p20-34
• Always hold your drill at right-angles to your work.
As a general
rule, for large
size drill bits use
hammer switch to the hammer mode
low speeds and
screwdriving, set the hammer switch to the drill
for smaller drill
mode
bits use high
• Set the forward/reverse switch to the correct
speeds.
direction.
• Never change the direction of rotation when your
drill is in operation.
Set the forward/
• After use, remove the drill bit and gently tap the side
reverse switch
of the chuck with a soft-faced hammer to remove
to the desired
the dust. This will extend the life of the chuck.
direction of
rotation. Never

COOLING DOWN

change the
If your drill becomes too hot in use, allow your drill to
operate without load for 2 minutes.
OVERLOAD
Never use excessive force when using your drill. Too
To switch your
much pressure can reduce the speed of your drill and
drill on, depress
reduce its efficiency. This can result in an overload
the variable
which can cause damage to the motor of your drill.
speed on/off
EC DECLARATION OF CONFORMITY
switch.
We declare that units: KR540RE, KR540CRE, KR550RE,
Your drill stops
when the switch KR550CRE, KR600RE, KR600CRE, KR650CRF conform
is released.
to 98/37/EC, 89/336/EEC, EN55014, 73/23/EEC,
If continuous
EN55104, EN50144
operation is
A weighted sound pressure 99dB (A)
required,
A weighted sound power 112dB (A)
depress the
Hand/arm weighted vibration 8.89m/s
lock-on button
while the
variable speed
on/off switch is
Brian Cooke - Director of Engineering
depressed.
Black & Decker Ltd, Spennymoor, County Durham
To stop your drill
DL16 6JG United Kingdom
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
24
When drilling
wood and metal,
set the hammer
switch to the drill
mode
When drilling
masonry, set the
.
2
06-02-2001, 15:48
.
. When