Black & Decker KR540 Original Instructions Manual page 7

• The forward/reverse switch controls the direction
of rotation when your drill is used as a
screwdriver, or when clearing a jammed drill bit.
• The adjustable depth stop gives precise control of
the hole depth, when you drill blind holes.
FITTING THE DRILL BIT (KEYLESS CHUCKS)
Disconnect the plug from the electricity supply.
Insert the drill bit in the jaws of the chuck. Hold the
rear section of the chuck while tightening the front
section. Twist the two sections firmly in opposite
directions to securely grip the drill bit.
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
the end of the chuck key in one of the three holes in
the body of the chuck, ensuring the head of the
chuck key is engaged with the barrel of the chuck.
Turn the chuck key clockwise to tighten the jaws and
securely grip the drill bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck, open the jaws, hold it firmly in
one hand and with a screwdriver held in the other
hand, turn the set-screw in the chuck clockwise
approximately one turn, to loosen it.
KR540-600 UK p01-12
the chuck on the spindle. Remove the allen key.
Use the screwdriver to turn the set-screw clockwise
until it totally disengages from the spindle. Remove
the chuck from the spindle by rotating it anti-
clockwise. To fasten the chuck, put it on the thread
and turn it clockwise until it stops. Put in the screw
and turn it anti-clockwise until absolutely firm.
While holding the
REMOVING THE CHUCK (KEYED CHUCKS)
rear section of
Proceed as follows:
the chuck, rotate
the front section
until the jaws of
the chuck are
sufficiently open.
the chuck clockwise with the other hand until it comes
out. Use only the correct chuck key. Place the chuck key
into the chuck, and hold the drill firmly in one hand with
the chuck pointing away from you. Rotate the chuck so
Rotate the barrel
that the chuck key is just above the horizontal position on
of the chuck until
the right hand side of the machine. Give the crossbar end
the jaws are
of the key a sharp downward blow with a mallet or light
sufficiently open.
hammer. The chuck should now be sufficiently loose to
Insert the drill bit
be unscrewed by hand.
in the jaws of the
chuck. Insert the
FITTING THE SIDE HANDLE
chuck key with
Proceed as follows:
the handle by turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
Place an allen
@@ yy PP @@ PP PP @@ PP @@ @@ @@ @@ @@ @@ @@ @@ @@ PP PP @@ PP @@ PP PP @@ @@ PP @@ @@ @@ PP @@ @@ PP PP PP @@ PP PP PP @@ @@ PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP PP @@ PP @@
key in the chuck
and tighten the
jaws. Give the
allen key a short yy PP @@ PP PP PP PP PP PP PP PP PP @@ @@ PP @@ PP @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ PP PP PP PP PP PP PP PP PP @@ @@ PP @@ PP @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@
powerful blow in
an anti-clockwise
direction with a
hammer to loosen
7
ENGLISH
To remove the
chuck, open the
jaws of the chuck
with the chuck
key. Hold the
chuck firmly in one
hand, and with a
screwdriver turn
the screw set in
@ @ @ @ @ @ @ @ @ @ @ @ P P @ @ P P @ @ P P @ @ P P @ @ y y @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P @ @ @ @ @ @
Loosely locate
the handle on the
body of your drill.
Rotate the handle
around the body
of your drill until
it is in the desired
position. Tighten
Fit the drill bit.
P y @ @ @ @ @ @ P @ P @ P P @ P @ @ @ P @ @ @ P @ @ P P @ @ P P @ @ @ P P @ P P P @ P P P @ P P P @ P P P @ @ P @ @ P P P @ @ P @ P P @ P P @ P @
Loosen the side
handle.
Slide the depth
stop until the end
of the depth stop
aligns with the
end of the drill bit.
06-02-2001, 10:23
7