Grandstream Networks HT502 User Manual
  1. Manuals
  2. Brands
  3. Grandstream Networks Manuals
  4. Adapter
  5. DUAL FXS PORT HT502
  6. User manual

Grandstream Networks HT502 User Manual

Dual fxs port analog telephone adaptor
Hide thumbs Also See for HT502:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, User Manual
Grandstream Networks, Inc.
HT502
Dual FXS Port
Analog Telephone Adaptor
HT502 USER MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Grandstream Networks HT502

Summary of Contents for Grandstream Networks HT502

  • Page 1 Grandstream Networks, Inc. HT502 Dual FXS Port Analog Telephone Adaptor HT502 USER MANUAL...

  • Page 2: Table Of Contents

    3-WAY CONFERENCING ........................19 FAX SUPPORT ............................ 20 CALL FEATURES ..................21 CONFIGURATION GUIDE ................. 23 CONFIGURING THE HT502 THROUGH VOICE PROMPTS ............. 23 CONFIGURING THE HT502 VIA WEB BROWSER ................24 ACCESS THE WEB CONFIGURATION MENU ................24 IMPORTANT SETTINGS ........................25 NAT SETTINGS ..........................
  • Page 3 PREFERRED VOCODER (CODEC) .................... 26 ADVANCED USER CONFIGURATION ....................30 SAVING THE CONFIGURATION CHANGES ..................43 REBOOTING THE HT502 FROM REMOTE ..................43 CONFIGURATION THROUGH A CENTRAL SERVER ............... 43 SOFTWARE UPGRADE ................45 FIRMWARE UPGRADE THROUGH TFTP/HTTP/HTTPS ..............45 INSTRUCTIONS LOCAL FIRMWARE UPGRADE: ................
  • Page 4 FIGURE 3: UPLINK/DOWNLINK BANDWIDTH LIMITATION ..............29 ABLE OF ABLES HT502 User Manual TABLE 1: DEFINITIONS OF THE HT502 CONNECTORS ............... 10 TABLE 2: DEFINITIONS OF THE HT502 LEDS ..................10 TABLE 3: HT502 TECHNICAL SPECIFICATIONS ..................12 TABLE 4: HT502 HARDWARE SPECIFICATION ..................14 TABLE 5: HT502 IVR MENU DEFINITIONS ....................

  • Page 5: Gnu Gpl Information

    GNU GPL INFORMATION HT502 firmware contains third-party software licensed under the GNU General Public License (GPL). Grandstream uses software under the specific terms of the GPL. Please see the GNU General Public License (GPL) for the exact terms and conditions of the license.

  • Page 6: Change Log

    CHANGE LOG This section documents significant changes from previous versions of HT502 user manuals. Only major new features or major document updates are listed here. Minor updates for corrections or editing are not documented here. CHANGES FROM 1.0.7.6 USER MANUAL ...

  • Page 7: Welcome

    User Manual, could void your manufacturer warranty. Please do not use a different power adaptor with the HT502 as it may cause damage to the products and void the manufacturer warranty.
  • Page 8 Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for any purpose is not permitted without the express written permission of Grandstream Networks, Inc. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL...

  • Page 9: Connect Your Ht502

    2. Insert a standard RJ11 telephone cable into the Phone1 port and connect the other end of the telephone cable to the analog telephone. 3. Insert the Ethernet cable into the WAN port of HT502 and connect the other end of the Ethernet cable to an uplink port (a router or a modem, etc.) 4.

  • Page 10: Figure 1: Connecting The Ht502

    (12V) FIGURE 1: CONNECTING THE HT502 The HT502 has two FXS port. Both FXS ports can have a separate SIP account. This is a key feature of HT502 as it supports simultaneous calls on both FXS ports. TABLE 1: DEFINITIONS OF THE HT502 CONNECTORS...

  • Page 11: Figure 2: Ht502 Connection Diagram

    NOTE: All LEDs display green when ON. Slow blinking of WAN and LAN LED together indicate the product in firmware upgrading or provision stat Internet ADSL/Cable Modem Ethernet Analog Phone Analog Phone Cordless Cordless Phone Phone FIGURE 2: HT502 CONNECTION DIAGRAM FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 11 of 49...

  • Page 12: Product Overview

    PRODUCT OVERVIEW The HT502 is a full feature voice and fax-over IP device that offers a high-level of integration including dual 10M/100Mbps network ports with integrated router, NAT, DHCP server, dual port FXS telephone gateway, market-leading sound quality, rich functionalities, and a compact and lightweight design. The VoIP network signaling protocol supported is SIP.
  • Page 13 3-way conferencing, message waiting, Do-Not-Disturb (DND), call-return service Caller ID Bellcore Type 1 & 2, ETSI, BT, NTT, and DTMF-based CID Polarity Reversal / Wink EN55022/EN55024 and FCC part15 Class B Safety FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 13 of 49...

  • Page 14: Hardware Specification

    HARDWARE SPECIFICATION The table below lists the hardware specification of HT502. TABLE 4: HT502 HARDWARE SPECIFICATION LAN Interface 2 x RJ45 10/100Mbps (integrated router) 5 LEDs (GREEN) Universal Switching Input: 100-240V AC, 50/60Hz, 0.5A Max Power Adaptor Output: 12V DC, 0.5A...

  • Page 15: Basic Operations

    UNDERSTANDING HT502 VOICE PROMPT HT502 has a built-in voice prompt menu for simple device configuration. The IVR menu and the LED button work with any of the FXS port. Pick up the handset and dial “***” to use the IVR menu.

  • Page 16: Placing A Phone Call

    Phone calls between FXS 1 User can make internal calls between two FXS ports on the same and FXS 2 port HT502 even without being registered to SIP server. By dialing *** and 70 user can reach the other FXS port Voice Mail Number of Voice Mails “RESET”...

  • Page 17: Direct Ip Calls

    2. Both HT502 and other VoIP Device are on the same LAN using private IP addresses, or 3. Both HT502 and other VoIP Device can be connected through a router using public or private IP addresses (with necessary port forwarding or DMZ).

  • Page 18: Call Hold

    4. Caller A dials *87 then dials caller C’s number, and then # (or wait for 4 seconds) 5. Caller A will hear the confirm tone. Then, A can hang up. NOTE: “Enable Call Feature” must be set to “Yes” in web configuration page. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 18 of 49...

  • Page 19: 3-Way Conferencing

    4. If Caller C does not answer the call, Caller A can press “flash” to resume call with Caller B. NOTE: When Attended Transfer fails and A hangs up, the HT502 will ring back user A to remind A that B is still on the call.

  • Page 20: Fax Support

    B and C can continue the conversation. FAX SUPPORT HT502 supports FAX in two modes: 1) T.38 (Fax over IP) and 2) fax pass through. T.38 is the preferred method because it is more reliable and works well in most network conditions. If the service provider supports T.38, please use this method by selecting Fax mode to be T.38 (default).

  • Page 21: Call Features

    CALL FEATURES The HT502 supports all the traditional and advanced telephony features. TABLE 6: HT502 CALL FEATURES Call Features Forcing a Codec (per call) *027110 (PCMU), *027111 (PCMA), *02723 (G723), *02729 (G729), *0272616 (G726-r16), *0272624 (G724-r24), *0272632 (G726-r32), *0272640 (G726-r40), *027201 (iLBC) Disable LEC (pe call) Dial “*03”...
  • Page 22 Toggles between active call and incoming call (call waiting tone). If not in conversation, flash/hook will switch to a new channel for a new call. Pressing pound sign will serve as Re-Dial key. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 22 of 49...

  • Page 23: Configuration Guide

    Select voice menu option 01 to enable HT502 to use DHCP. STATIC IP M Select voice menu option 01 to enable HT502 to use STATIC IP mode, then use option 02, 03, 04, 05 to set up IP address, Subnet Mask, Gateway and DNS server respectively.

  • Page 24: Configuring The Ht502 Via Web Browser

    CONFIGURING THE HT502 VIA WEB BROWSER HT502 has an embedded Web server that will respond to HTTP GET/POST requests. It also has embedded HTML pages that allow users to configure the HT502 through a web browser such as Microsoft’s IE, AOL’s Netscape or Mozilla Firefox installed on Windows or Unix OS. (Macintosh OS is not included).

  • Page 25: Important Settings

    Yes. If using a Public IP address, set this parameter to No. 3. NAT Traversal (under the Profile web pages) Set this to Yes when gateway is behind firewall on a private network. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 25 of 49...

  • Page 26: Dtmf Methods

    Set priority of DTMF methods according to your preference. This setting should be based on your server DTMF setting. PREFERRED VOCODER (CODEC) The HT502 supports a broad range of voice codecs. Under Profile web pages, choose your preferred order of different codecs:  PCMU/A (or G711µ/a) ...
  • Page 27 Device Mode This parameter controls whether the device is working in NAT router mode or Bridge mode. Save the setting and reboot prior to configuring HT502. NAT Maximum Ports The number of ports that can be managed while in NAT router mode.
  • Page 28 When set to “Yes”, the HT502 acts as an UPnP gateway for your UPnP enabled Enable UPnP applications. UPnP = “Universal Plug and Play” Default is No. When set to “Yes”, the HT502 responds to the PING command from other Reply to ICMP on WAN Port computers, but is also made vulnerable to DOS attacks.

  • Page 29: Figure 3: Uplink/Downlink Bandwidth Limitation

    DMZ IP: This function forwards all WAN IP traffic to a specific IP address if no matching port is used by HT502 or in the defined port forwarding. Port Forwarding Forwards a matching (TCP/UDP) port to a specific LAN IP address with a specific (TCP/UDP) port.

  • Page 30: Advanced User Configuration

    PPPoE Link Up Indicates whether the PPPoE connection is up if the HT502 is connected to DSL modem. This filed indicates the type of NAT connection used by the HT502 via its WAN port. Port Status Displays relevant information regarding the each FXS port.

  • Page 31: Table 9: Advanced Settings

    TCP port where the HTTP or HTTPS server is listening; it can be omitted if using default port 80. Note: If Auto Upgrade is set to No, HT502 will only do HTTP/HTTPS download once at boot up. FIRMWARE VERSION 1.0.8.4...
  • Page 32 23. If select “Yes, weekly on day” make sure you input the day of the week (in format 0-6, 0 is Sunday) you want it to check for update. When set to No, HT502 will only do the following option you select; “Always check for New Firmware at Boot up” will check for new firmware every time the device reboots.
  • Page 33 OFF should be zero. Otherwise it will ring ON ms and a pause of OFF ms and then repeat the pattern. Example configuration for N.A. Dialtone: f1=350@-13,f2=440@-13,c=0/0; Syntax: f1=freq@vol, f2=freq@vol, c=on1/off1-on2/off2-on3/off3; [...] (Note: freq: 0 - 4000Hz; vol: -30 - 0dBm) FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 33 of 49...
  • Page 34 (Internet Telephone Service Provider) Syslog Level Select the HT502 to report the log level. Default is NONE. The level is one of DEBUG, INFO, WARNING or ERROR. Syslog messages are sent based on the following events: 1. product model/version on boot up (INFO level) 2.

  • Page 35: Table 10: Account Settings

    IP address and port in all of its SIP and SDP messages. If the NAT Traversal field is set to “Yes” with no specified STUN server, the HT502 will periodically (every 20 seconds or so) send a blank UDP packet (with no payload data) to the SIP server to keep the “hole”...
  • Page 36 Retry registration if the process failed. Default is 30 seconds. Time Local SIP port Defines the local SIP port the HT502 will listen and transmit. The default value for FXS port 1 is 5060. The default value for FXS port 2 is 5062. Local RTP port Defines the local RTP-RTCP port pair the HT502 will listen and transmit.
  • Page 37 This parameter allows users to configure a User ID or extension number that is automatically dialed when off-hook. Only the user part of a SIP address needs is entered here. The HT502 will automatically append the “@” and the host portion of the corresponding SIP address.
  • Page 38 If set to “Yes”, an INVITE is sent using the dial-number collected thus far; Otherwise, no INVITE is sent until the “(Re-)Dial” button is pressed or after about 5 seconds have elapsed if the user forgets to press the “Re-Dial” button. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 38 of 49...
  • Page 39 ^1900x. - prevents dialing any number started with 1900 • <=1617>[2-9]xxxxxx - allows dialing to local area code (617) numbers by dialing 7 numbers and 1617 area code will be added automatically FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 39 of 49...
  • Page 40 As a Callee, select UAC to use caller or proxy server as the refresher, or UAS to use the phone as the refresher. Force INVITE Session Timer can be refreshed using INVITE method or UPDATE method. Select “Yes” to use INVITE method to refresh the session timer. FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 40 of 49...
  • Page 41 INVITE. Preferred Vocoder The HT502 supports up to 5 different Vocoder types including G.711 A-/U-law, G.726 (Supports bit rates 16, 24, 32 and 40), G.723.1, G.729A/B/E, iLBC and AAL2. The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message.
  • Page 42 Polarity Reversal termination. Loop Current Default is No. Set it to Yes if the traditional PBX you are using with HT502 uses this Disconnect method for signaling call termination. Method initiates short voltage drop on the line when remote (VoIP) side disconnects an active call.

  • Page 43: Saving The Configuration Changes

    SAVING THE CONFIGURATION CHANGES Click the “Update” button in the Configuration page to save the changes to the HT502 configuration. The following screen confirms that the changes are saved. Reboot or power cycle the HT502 to make the changes take effect.
  • Page 44 Grandstream also provides configuration tools (Windows and Linux/Unix version) to facilitate the task of generating device configuration files. The Grandstream configuration tools are free to end users. The configuration tools configuration templates available download from http://www.grandstream.com/support/tools FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 44 of 49...

  • Page 45: Software Upgrade

    TFTP/HTTP/HTTPS fails for any reason (e.g. TFTP/HTTP/HTTPS server is not responding, there are no code image files available for upgrade, or checksum test fails, etc), the HT502 will stop the TFTP/HTTP/HTTPS process and simply boot using the existing code image in the flash.

  • Page 46: Instructions Local Firmware Upgrade

    1. Unzip the file and put all of them under the root directory of the TFTP server. 2. Put the PC running the TFTP server and the HT502 device in the same LAN segment. 3. Please go to File -> Configure -> Security to change the TFTP server's default setting from "Receive Only"...

  • Page 47: Firmware And Configuration File Prefix And Postfix

    File download in minutes to reduce the Firmware or Provisioning Server load at any given time. Automatic Upgrade: 10080 Yes, every minutes(60-5256000). Yes, daily at hour (0-23). Yes, weekly on day (0-6). FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 47 of 49...

  • Page 48: Restore Factory Default Setting

    4. Wait 15 seconds and device will automatically reboot and restore factory settings. Encode the MAC Address 1. Locate the MAC address of the device. It is the 12 digit HEX number on the bottom of the FIRMWARE VERSION 1.0.8.4 HT502 USER MANUAL Page 48 of 49...

  • Page 49: Firmware Version 1.0.8.4 Ht502 User Manual

    1. Factory Reset will be disabled if the “Lock keypad update” is set to “Yes”. 2. Please be aware by default the HT502 WAN side HTTP access is disabled. After a factory reset, the device’s web configuration page can be accessed only from its LAN port.

Table of Contents