SLV-D990P B/D990P E/D990P R/D995P E 3 7 63 1515 0 RMT-V503C/V503D SERVICE MANUAL AEP Model SLV-D990P B/D990P E/D995P E Russian Model SLV-D990P R TS-10 MECHANISM Refer to the SERVICE MANUAL of VHS MECHANI- CAL ADJUSTMENT MANUAL VII for MECHANICAL ADJUSTMENTS. (9-921-790-11) SPECIFICATIONS L 13942296513...
Page 2
Output signal: 1 Vp-p, 75 ohms, unbal- Standby power consumption anced, sync negative 2.6 W (Power Save On mode, minimum) AUDIO OUT, phono jacks (2) SLV-D990P R: Standard output: 327 mVrms Power back-up Load impedance: 47 kilohms Back-up duration: 1 hour at a time...
Page 3
IC pins, etc. OPERATION. REPLACE THESE COMPONENTS WITH • Usable with ordinary solder SONY PARTS WHOSE PART NUMBERS APPEAR AS It is best to use only unleaded solder but unleaded solder may SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- also be added to ordinary solder.
http://www.xiaoyu163.com 3 7 63 1515 0 PRECAUTIONS 1 SAFETY PRECAUTIONS 1) Before returning an instrument to the customer, always make a (4) Insulation Resistance Test Cold Check-(1) Unplug the power safety check of the entire instrument, including, but not limited supply cord and connect a jumper wire between the two prongs to, the following items: of the plug.
Page 6
http://www.xiaoyu163.com 3 7 63 1515 0 6) Product Safety Notice-Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc.
http://www.xiaoyu163.com 3 7 63 1515 0 2 SERVICING PRECAUTIONS CAUTION: Before servicing units covered by this service manual and its supplements, read and follow the Safety Precautions section of this manual. Note: If unforseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
http://www.xiaoyu163.com 3 7 63 1515 0 3 ESD PRECAUSIONS Electrostatically Sensitive Devices (ESD) Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components.
http://www.xiaoyu163.com 3 7 63 1515 0 4 HANDLING THE OPTICAL PICK-UP The laser diode in the optical pick up may suffer electrostatic breakdown because of potential static electricity from clothing and your body. The following method is recommended. (1) Place a conductive sheet on the work bench (The black sheet used for wrapping repair parts.) (2) Place the set on the conductive sheet so that the chassis is grounded to the sheet.
http://www.xiaoyu163.com 3 7 63 1515 0 5 PICK-UP DISASSEMBLY AND REASSEMBLY 5-1 Disassembly 5-2 Assembly 1) Replace the Pick-up. 1) Remove the power cord. 2) Remove the soldering 2 points on Pick-up. 2) Disassemble the Deck-Assy. 3) Reassemble the Deck-Assy. 3) Make solder land 2 points short on Pick-up.
http://www.xiaoyu163.com SLV-D990P B/D990P E/D990P R/D995P E 3 7 63 1515 0 1. GENERAL This section is extracted from instruction manual. (2-585-815-13) Ce lecteur ne peut pas lire non plus les disques Code régional A propos de ce mode Ce lecteur peut lire les suivants : •...
Page 12
La télécommande est préprogrammée pour commander des téléviseurs de marques l’extrémité positive (+) s’engage. autres que Sony. Si votre téléviseur figure dans le tableau suivant, spécifiez le numéro de code de fabricant correspondant. Utilisation de la Capteur de télécommande...
Page 13
http://www.xiaoyu163.com 3 7 63 1515 0 Si votre téléviseur comporte un connecteur Scart (EURO- Autres raccordements A un tuner satellite ou numérique avec la fonction Ligne passante LINE-3 La fonction Ligne passante vous LINE OUT permet de regarder sur votre téléviseur des émissions depuis un tuner satellite ou numérique raccordé...
Page 14
http://www.xiaoyu163.com 3 7 63 1515 0 Pour annuler la fonction de réglage automatique Etape 5 : Sélection de la langue des menus Appuyez sur SET UP. Pour modifier le canal RF Vous pouvez changer la langue d’affichage Si l’image n’apparaît pas clairement sur le téléviseur, modifiez le canal RF sur le des menus.
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 Conseils Appuyez sur V/v pour régler les heures. • Si vous placez « Horloge Auto » sur « Oui », la fonction de réglage automatique de l’horloge REGLAGE HORLOGE est activée à chaque fois que vous éteignez le lecteur DVD-magnétoscope. L’heure est réglée ENTER automatiquement par référence au signal horaire diffusé...
Page 16
http://www.xiaoyu163.com 3 7 63 1515 0 Changement/désactivation de numéros de chaîne Appuyez sur O RETURN, puis appuyez sur SET UP pour quitter le menu. Après avoir réglé les canaux, vous pouvez changer des numéros de chaîne. Si un RETURN numéro de chaîne est inutilisé ou attribué à un canal que vous ne désirez pas conserver, SET UP vous pouvez le désactiver.
Page 17
http://www.xiaoyu163.com 3 7 63 1515 0 Changement du nom de chaîne Appuyez sur V/v pour sélectionner LISTE DES CHAÎNES Vous pouvez changer ou saisir le nom de « Installation Manuelle », puis appuyez sur CAN. chaîne (jusqu’à 4 caractères). Le lecteur ENTER ENTER.
http://www.xiaoyu163.com 3 7 63 1515 0 Réglage pour une chaîne TV-PAYANTE/Canal Plus Appuyez sur V/v pour sélectionner la ligne RECHERCHE MANUELLE Pour regarder ou enregistrer des émissions que vous désirez spécifier pour le décodeur, TV-PAYANTE/Canal Plus, réglez le lecteur puis appuyez sur b. CANAL SET UP ENTER...
Page 19
http://www.xiaoyu163.com 3 7 63 1515 0 Conseils Pour Appuyez sur • La fonction Instant Replay vous permet de revoir une scène ou de réécouter un dialogue que m ou M de la télécommande (ou appuyez Localiser rapidement un point vous avez manqués. continuellement sur m ou M de l’appareil) •...
Page 20
http://www.xiaoyu163.com 3 7 63 1515 0 Exemple : Lors de la lecture d’un CD de données/DVD de données (fichier vidéo Conseil DivX* seulement) • Vous pouvez changer l’information de position de compteur (temps de lecture ou temps restant) à l’aide de (DVD et CD seulement).
Page 21
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur H. Lecture d’une cassette Le temps de lecture est indiqué dans la fenêtre d’affichage. Avant de commencer... Lorsque la cassette arrive en fin • Mettez le lecteur DVD-magnétoscope et le de bande, elle se rembobine téléviseur sous tension.
Page 22
http://www.xiaoyu163.com 3 7 63 1515 0 • Pour enregistrer un canal normal, appuyez sur PROG +/– jusqu’à ce que • PROG/ Enregistrement d’émissions TRACKING le numéro de la chaîne que vous désirez enregistrer s’affiche dans la fenêtre d’affichage. Avant de commencer... •...
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur SET UP, puis appuyez sur V/v Enregistrement d’émissions à l’aide du OPTIONS PROG. SET UP pour sélectionner (TIMER) et appuyez Normal ShowView système ShowView ® sur ENTER. Vous pouvez également afficher (SLV-D995P E/D980P D le menu de programmation du programmateur seulement) en appuyant sur TIMER.
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 Remarques • Si le signal VPS/PDC est trop faible ou si la chaîne n’émet pas de signaux VPS/PDC, le Enregistrement d’émissions à l’aide du magnétoscope démarrera l’enregistrement à l’heure programmée sans utiliser la fonction VPS/PDC.
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 Remarques • Lors d’une programmation avec des signaux VPS/PDC, spécifiez les heures de début Enregistrement d’émissions à l’aide de d’enregistrement exactement comme indiqué dans le programme de télévision. A défaut, la fonction VPS/PDC serait inopérante. DIAL TIMER (SLV-D995P E seulement) •...
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 A propos du mode de démonstration Appuyez sur DIAL TIMER pour terminer la programmation. DIAL TIMER La fonction Dial Timer dispose d’un mode de démonstration qui permet à l’utilisateur « OK » apparaît dans la fenêtre d’affichage pendant environ cinq secondes. (un vendeur, par exemple) de saisir plus de six exemples de programmations L’indicateur apparaît dans la fenêtre d’affichage et le magnétoscope se...
http://www.xiaoyu163.com 3 7 63 1515 0 Raccordements avancés B Utilisez cette méthode de raccordement si votre récepteur A/V est Raccordement d’un récepteur A/V doté d’un décodeur Dolby Digital, MPEG audio ou DTS*, d’une prise d’entrée numérique et de 6 enceintes Ce raccordement vous permet d’utiliser la fonction de décodeur Dolby Digital, MPEG audio ou DTS de votre amplificateur (récepteur) A/V.
http://www.xiaoyu163.com 3 7 63 1515 0 Paramètres et réglages DVD B Utilisez cette méthode de raccordement si votre téléviseur est doté de prises d’entrée vidéo composantes Options audio Raccordez votre téléviseur par les prises COMPONENT VIDEO OUT à l’aide d’un cordon vidéo composantes (non fourni) ou de trois cordons vidéo (non fournis) de «...
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur B/b pour sélectionner un élément. Réglage de l’écran ENTER « Réglage de L’écran » vous permet de régler SET UP l’écran en fonction des conditions de lecture et de raccordement. Appuyez sur SET UP pour quitter le menu. SET UP Choix de menu •...
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur V/v pour sélectionner l’élément dont vous désirez changer la Sélection de la langue de l’affichage ou de langue sur la liste : ENTER « Menu DVD », « Audio » ou « Sous-Titre ». la piste sonore Appuyez ensuite sur ENTER.
http://www.xiaoyu163.com 3 7 63 1515 0 Autres opérations du lecteur DVD Appuyez sur SET UP pour quitter le menu. SET UP Utilisation du menu DVD Un DVD est divisé en longues sections d’images ou de son appelées « titres ». Lors Pour changer le mot de passe (code secret) de la lecture d’un DVD vidéo contenant Sélectionnez «...
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez plusieurs fois sur B/b ou utilisez les touches numériques pour Changement de l’angle de vue sélectionner le numéro d’angle de vue. ENTER La scène passe sur l’angle de vue sélectionné. Si le DVD vidéo comporte plusieurs angles de vue (multiangle) pour une scène, «...
Page 33
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur B/b pour sélectionner Autres modes de lecture PROGRAMMATION (lecture « PROGRAMMATION », puis appuyez sur Plage Ordre Programme ENTER ENTER. – – – – – – – – programmée, lecture aléatoire, lecture répétée) –...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur REPEAT ou B/b pour sélectionner l’élément à répéter. Changement du son REPEAT/ INDEX Lors de la lecture d’un DVD • Chapitre : pour répéter le chapitre actuel. • Titre : pour répéter le titre actuel d’un disque. Lors de la lecture d’un DVD vidéo ou CD de Lors de la lecture d’un CD vidéo (avec la fonction PBC données/DVD de données (fichier vidéo...
Page 35
http://www.xiaoyu163.com 3 7 63 1515 0 Pour désactiver la fonction Lecture de plages audio MP3 Sélectionnez « Non » à l’étape 2. Remarques Le lecteur permet de lire des CD de données • Lors de la lecture d’un son qui ne contient pas de signal pour les enceintes arrière, l’effet (CD-ROM/CD-R/CD-RW) ou des DVD de surround est difficilement perceptible.
Page 36
http://www.xiaoyu163.com 3 7 63 1515 0 Pour arrêter la lecture programmée Remarques • Si vous ajoutez l’extension « .MP3 » à un fichier qui n’est pas de format MP3, le lecteur ne Appuyez sur x pendant la lecture programmée. pourra pas le reconnaître correctement et produira un bruit important susceptible d’endommager les enceintes.
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 Pour faire pivoter l’image sélectionnée Appuyez sur Z et placez un CD de données ou Appuyez sur V/v/B/b pour sélectionner une image un DVD de données sur le plateau, puis Sélectionnez le type de media appuyez sur Z pour fermer le plateau.
Page 38
http://www.xiaoyu163.com 3 7 63 1515 0 Pour passer à la page suivante ou revenir à la précédente Appuyez sur V/v pour sélectionner « DivX », DivX Appuyez sur b ou B. puis appuyez sur ENTER. ALBUM:007 FICHIERS:014 album 1 fichier DivX 1 ENTER album 2 fichier DivX 2...
http://www.xiaoyu163.com 3 7 63 1515 0 Autres opérations du magnétoscope Appuyez sur ENTER. Enregistrement Programmé Immédiat ENTER Après avoir lancé l’enregistrement, vous pouvez faire en sorte que le magnétoscope s’arrête automatiquement après la durée Suivez les instructions du menu pour les opérations interactives. spécifiée.
Page 40
http://www.xiaoyu163.com 3 7 63 1515 0 Pour sélectionner le son pendant l’enregistrement Comment est enregistré le son sur une cassette vidéo Appuyez sur AUDIO pour sélectionner le son désiré. Le magnétoscope enregistre le son sur deux pistes séparées. Le son Hi-Fi est enregistré...
Page 41
http://www.xiaoyu163.com 3 7 63 1515 0 Appuyez sur V/v pour sélectionner Réglage de l’image REGLAGES UTILISATEUR (alignement) « Réglages Utilisateur », puis appuyez sur Syst. Couleur Auto ENTER ENTER. NICAM Smart Trilogic Réglage de l’alignement Etendre ShowView Bien que le magnétoscope règle RETURN SET UP automatiquement l’alignement pendant la...
http://www.xiaoyu163.com 3 7 63 1515 0 Exemple B Montage Téléviseur Votre magnétoscope (enregistreur) Comment effectuer le raccordement pour enregistrer sur ce magnétoscope Raccordez les sorties de ligne de l’autre magnétoscope au connecteur d’entrée de ligne de ce magnétoscope. Reportez-vous aux exemples A à C et choisissez le raccordement qui LINE-2 IN t/o L/R correspond le mieux à...
Page 43
Appuyez sur ENTER pour valider les messages. Si vous avez des questions ou des problèmes qui ne sont pas traités dans le tableau qui suit, consultez le centre de service après-vente Sony le plus proche. Appuyez sur SET UP pour quitter le menu.
Page 44
Les autres caractères s’affichent comme des astérisques. Guide de dépannage). Nettoyez les têtes vidéo à l’aide d’une cassette de nettoyage de têtes vidéo Sony. Si cette La lecture ne commence pas au début • La lecture programmée, aléatoire ou répétée a été...
Page 45
http://www.xiaoyu163.com 3 7 63 1515 0 DVD-RW (page 6) Plage (page 41) Glossaire Un DVD-RW est un disque enregistrable et La plage est une partie d’un segment image réinscriptible de même taille qu’un DVD ou audio d’un CD ou CD vidéo (la durée vidéo.
Page 46
http://www.xiaoyu163.com 3 7 63 1515 0 A Touche Z (ouverture/fermeture) (36) Panneau arrière Télécommande pour DVD (38) B Commutateur TV / DVD·VIDEO (téléviseur/lecteur DVD-magnétoscope) (10) C Touche SELECT DVD (mode DVD) (10) D Touches numériques* (11) (85) E Touche CLEAR (annulation) (30) (95) F Touche SURROUND (101) G Touche SET UP (réglage) (18) H Touche SUBTITLE (sous-titre) (92)
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 Réglage du programmateur Index à l’aide de DIAL TIMER à l’aide du système Chiffres ShowView 54 enregistrement programmé 16:9 79 Emissions NICAM 121 Manipulation des disques 8 immédiat 119 4:3 Letter Box (non recadré) 79 Emissions ZWEITON 121 Mode AV personnalisé...
http://www.xiaoyu163.com SLV-D990P B/D990P E/D990P R/D995P E 3 7 63 1515 0 2. DISASSEMBLY AND REASSEMBLY 2-1 CABINET AND PCB 2-1-1 Cabinet Top Removal 2-1-3 Ass’y Front Panel Removal 2 Lift up the Cabinet Top in the direction of arrow 1 RELEASE 4 HOOKS 1 REMOVE 3 SCREWS (Top view) Fig.
http://www.xiaoyu163.com 3 7 63 1515 0 2-3 VCR DECK PARTS LOCATIONS 2-3-1 Top View L 13942296513 Fig. 2-8 Top parts Location-1 1 GEAR FL CAM 2 MOTOR LOADING ASS’Y 3 LEVER FL ARM ASS’Y 4 HOLDER FL CASSETTE ASS’Y 5 LEVER FL DOOR 6 SLIDER FL DRIVE u163 http://www.xiaoyu163.com...
Page 53
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 qa 0 qs Fig. 2-9 Top Parts Location-2 1 FE HEAD 8 DISK S REEL 2 CYLINDER ASS’Y 9 LEVER S BRAKE ASS’Y 3 ACE HEAD ASS’Y 0 GEAR IDLE 4 LEVER UNIT PINCH ASS’Y qa LEVER IDLE 5 LEVER #9 GUIDE ASS’Y qs LEVER T BRAKE ASS’Y...
http://www.xiaoyu163.com 3 7 63 1515 0 2-4 VCR DECK 2-4-1 Holder FL Cassette Ass’y Removal 2-4-2 Lever FL Arm Ass’y Removal 1) Pull the Holder FL Cassette Ass’y 1 to the eject position. 1) Push the hole “A” in the direction of arrow “B” use the pin.(about 2) Pull the Holder FL Cassette Ass’y 1 as grasping the Holder FL Dia.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-3 Lever FL Door Removal 2-4-4 Slider FL Drive, Gear FL Cam Removal 1) Release the Hook 2 and Remove the Lever FL Door 1 in the 1) Pull the Slider FL Drive 1 to the front direction. direction of arrow “A”.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-9 Gear Loading Drive, Slider Cam, 2-4-10 Gear Loading Drive, Slider Cam, Lever Load S, T Ass’y Removal Lever Load S, T Ass’y Assembly 1) Remove the Belt Pulley. (Refer to Fig. 2-38) 1) When reinstalling, be sure to align dot of Lever Load T Ass’y 2) Remove the Gear Loading Drive 1 after releasing Hook [A] in 1 with dot of Lever Load S Ass’y 2 as shown in drawing, the direction arrow as shown in detail drawing.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-11 Lever Pinch Drive, 2-4-12 Lever Tension Ass’y, Lever Tension Drive Removal Band Brake Ass’y Removal 1) Remove the Lever Pinch Drive 1, Lever Tension Drive 2. 1) Remove the Lever Brake S Ass’y (Refer to Fig 2-25). 2) Remove the Spring Tension Lever 1.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-13 Lever Brake S, T Ass’y Removal 2-4-14 Gear Idle Ass’y Removal 1) Push the Lever Idle 1 in the direction of arrow “A”, “B”. 1) Release the Hook [A] and the Hook [B], [C] in the direction of arrow as shown in Fig 2-25.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-15 Disk S, T Reel Removal 2-4-16 Holder Clutch Ass’y Removal 1) Lift the Disk S, T Reel 1, 2. 1) Remove the Washer Slit 1. 2) Lift the Holder Clutch Ass’y 2. Note: When you reinstall Holder Clutch Ass’y 1 DISK S REEL 1) Check the condition of spring as shown in detail A.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-17 Lever Up Down Ass’y, Gear Center 2-4-18 Guide Cassette Door Removal Ass’y Removal 1) Lift the Hook [A]. 2) Rotate the Guide Cassette Door 1 in the direction of arrow. 1) Remove the 2 hooks in the direction of arrow as shown Fig. 2- 29 and lift the Lever Up Down Ass’y 1.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-19 Lever Unit Pinch Ass’y, Plate Joint, 2-4-20 Lever #9 Guide Ass’y Removal Spring Pinch Drive Removal 1) Remove the Spring #9 Guide 1. 2) Lift the Spring #9 Guide Ass’y 2 in the direction of arrow “A”. 1) Lift the Unit Pinch Ass’y 1.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-21 FE Head Removal 2-4-22 ACE Head Removal 1) Rotate the FE Head 1 in the direction of arrow to lift up. 1) Pull out the FPC from connector of ACE Head Ass’y 2. 2) Remove the screw 1.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-23 Slider S, T Ass’y Removal 2-4-24 Plate Ground Deck, Cylinder Ass’y Re- moval 1) Move the Slider S, T Ass’y 1, 2 to slot, and then lift it to remove. (Refer to arrow) 1) Remove the 3 Screws 1.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-25 Belt Pulley Removal 2-4-27 Motor Capstan Ass’y Removal 1) Remove the Belt Pulley 1. 1) Remove the 3 Screws 1. 2) Remove the Motor Capstan Ass’y 2. Note: Take extreme care not to get grease on Belt Pulley 1 at Assembly: assembling or reassembling.
http://www.xiaoyu163.com 3 7 63 1515 0 2-4-28 Post #8 Guide Ass’y Removal 2-4-30 How to Eject the Cassette Tape (If the tape is stuck in the unit) 1) Rotate the Post #8 Guide Ass’y 1 in the direction of arrow to lift up.
http://www.xiaoyu163.com 3 7 63 1515 0 2-5 THE TABLE OF CLEANING, LUBRICATION AND REPLACEMENT TIME ABOUT PRINCIPAL PARTS 1) The replacement time of parts is not life of parts. 2) The table 2-1 is that the VCR Set is in normal condition (normal temperature, normal humidity). The checking period may be changed owing to the condition of use, runtime and environmental conditions.
http://www.xiaoyu163.com 3 7 63 1515 0 2-6 DVD DECK 2-6-1 Holder Chuck Removal 1) Push 4 Hooks 1 in the direction of arrow “A” and lift up the Holder Chuck 2. 2 HOLDER CHUCK 1 2 HOOKS "A" 1 2 HOOKS "A"...
http://www.xiaoyu163.com 3 7 63 1515 0 2-6-2 Tray Disc Removal 1) Insert a Screw Driver 1 into Emergency Hole 2 and push the Slider Housing 3 in the direction arrow “A”. 2) When the Tray Disc 4 comes out a little, pull it in the direction arrow “B” by hand. 3 SLIDER HOUSING 4 TRAY DISC "B"...
http://www.xiaoyu163.com 3 7 63 1515 0 2-6-4 Ass’y Housing Removal 1) Remove the 2 Soldering 1. (TM+, TM-) 2) Push the 2 Hooks 2 in the direction of arrow “A” and remove Ass’y PCB Deck 3. 3) Push the Slider Housing 4 in the direction arrow “B”. 4) Push the 1 Hook 5 in the direction of arrow “C”...
http://www.xiaoyu163.com 3 7 63 1515 0 2-6-5 Ass’y Bracket Deck Removal 1) Push the Hook 1 in the direction of arrow “A” and lift up the Gear Feed B 2. 2) Push the Hook 3 in the direction of arrow “B” and lift up the Gear Feed B 4. 3) Remove the 2 Screws 5 and lift up Motor Feed Ass’y 6.
http://www.xiaoyu163.com SLV-D990P B/D990P E/D990P R/D995P E 3 7 63 1515 0 6. ALIGNMENT AND ADJUSTMENTS 6-1 VCR ADJUSTMENT 6-1-1 Reference 1) X-Point (Tracking center) adjustment, “Head switching adjustment” and “NVRAM option setting” can be adjusted with remote control. 2) When replacing the Main PCB Micom (IC601) and NVRAM (IC605: EEPROM) be sure to adjust the “Head switching adjustment” and “NVRAM option setting”.
Page 100
http://www.xiaoyu163.com 3 7 63 1515 0 6-1-1(b) TEST location for adjustment mode setting L 13942296513 TEST TEST BUTTON Fig. 6-2 VCR Main PCB (Top View) u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 6-1-2 Head Switching Point Adjustment 1) Playback the alignment tape. 2) Press the “TEST” botton on VCR MAIN PCB to set the adjustment mode. (See Fig. 6-2) 3) Press the “1, 0” buttons ; remote control adjustment operates automatically. (See Fig. 6-1) 6-1-3 NVRAM Option Setting 1) NVRAM Option is adjusted in the factory.
http://www.xiaoyu163.com 3 7 63 1515 0 6-2 VCR MECHANICAL ADJUSTMENT 6-2-1 Tape Transport System and Adjustment Locations The tape transport system has been adjusted precisely in the factory. Alignment is not necessary except for the following : 1) Noise observed on the screen. 2) Tape damage.
http://www.xiaoyu163.com 3 7 63 1515 0 6-2-2 Tape Transport System Adjustment When parts are replaced, perform the required adjustments by referring to procedures for the tape transport system. If there are any changes to the tape path, first run a T-120 tape and make sure excessive tape wrinkle does not occur at the tape guides. If tape wrinkle is observed at the guide roller S, T, turn the guide roller S, T until wrinkle disappears.
Page 105
http://www.xiaoyu163.com 3 7 63 1515 0 b. ACE HEAD TILT ADJUSTMENT 1) Playback a blank tape and observe the position of the tape at the lower flange of tape guide. 2) Confirm that there is no curl or wrinkle at the lower flange of tape guide as shown in Fig. 6-9 (B). 3) If a curl or wrinkle of the tape occurs, slightly turn the screw (A) tilt adjust on the ACE head ass’y.
Page 106
http://www.xiaoyu163.com 3 7 63 1515 0 d. ACE HEAD POSITION (X-POINT) ADJUSTMENT 1) Playback the alignment tape (Color bar) 2) Press the “TEST” botton on VCR MAIN PCB to set the adjustment mode. (See Fig. 6-2) 3) Press the “0, 5” remote control buttons, then adjustment is operates automatically. (See Fig. 6-1) 4) Connect the CH-1 probe to “Envelope”...
Page 107
http://www.xiaoyu163.com 3 7 63 1515 0 (2) Linearity adjustment (Guide roller S, T adjustment) 1) Playback the Mono Scope alignment tape (SP mode). 2) Observe the video envelope signal on an oscilloscope (triggered by the video switching pulse). 3) Make sure the video envelope waveform (at its minimum) meets the specification shown in Fig. 6-11. If it does not, adjust as follows : Note: a=Maximum output of the video RF envelope.
Page 108
http://www.xiaoyu163.com 3 7 63 1515 0 6) Play back the Mono Scope alignment tape (SP mode). 7) Connect an oscilloscope CH-1 to the “Envelope” and CH-2 to the “H’D SW Pulse” for triggering. 8) Turn the guide roller heads with a flat head ( ) driver to obtain a flat video RF envelope as shown in Fig.
http://www.xiaoyu163.com 3 7 63 1515 0 (4) Envelope Check 1) Make recordings on T-120 (E-120) and T-160 (E-180) tape. Make sure the playback output envelope meets the specification as shown in Fig. 6-15. 2) Play back a self recorded tape (recording made on the unit using with T-120 (E-120). The video envelope should meet the specification as shown in Fig.
http://www.xiaoyu163.com 3 7 63 1515 0 8-1 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark have some differences from the original one. in the exploded views are not supplied. dotted line with mark are critical for safety.
http://www.xiaoyu163.com 3 7 63 1515 0 8-1-3 VCR Mechanical Parts (Bottom Side) T046 W018 not supplied not supplied T044 not supplied not supplied not supplied not supplied not supplied not supplied L 13942296513 not supplied not supplied not supplied not supplied not supplied not supplied W019...
http://www.xiaoyu163.com 3 7 63 1515 0 8-1-4 DVD Mechanical Parts W212 not supplied not supplied not supplied W012 H241 H206 H211 H203 not supplied W273 H210 W010 supplied H202 not supplied H204 L 13942296513 H205 H105 not supplied H207 H106 H103 W011 not supplied...
http://www.xiaoyu163.com DIAL DVD MAIN FUNCTION TIMER 3 7 63 1515 0 8-2 ELECTRICAL PARTS LIST • Items marked “*” are not stocked since they are NOTE: When indicating parts by reference number, • Due to standardization, replacements in the seldom required for routine service. Some delay please include the board name.