Related Manuals for Yeti Cycles ASRC
Summary of Contents for Yeti Cycles ASRC
- Page 1 YETI ASR OWNER’S MANUAL YETI CYCLES 621 Corporate Circle, Unit B Golden, CO 80401 888.576.9384 www.yeticycles.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS BRAND OVERVIEW FRAME FEATURES GEOMETRY MAINTENANCE SCHEDULE SETUP SHOCK SETUP QUICK START GUIDE CABLE/LINE SETUP TECHNICAL ASSEMBLY OVERVIEW EXPLODED VIEWS REBUILD KITS LEGAL WARRANTY CONTACT INFORMATION... - Page 3 WELCOME TO THE TRIBE. CONGRATULATIONS ON YOUR PURCHASE OF A NEW YETI. We are confident your new bicycle will exceed This manual outlines basic setup and your expectations for value, performance, and maintenance recommendations of your new ride quality. Each frameset and component Yeti.
- Page 4 OUR NEW ASR-C IS A Yeti’s custom high modulus carbon construction offers unparalleled stiffness and ride quality. It also offers best in category frame CROSS-COUNTRY RACE weight. Distinctive and functional Loopstays provide unparalleled ride MACHINE WITH AN quality and stiffness. Full carbon linkage reduces weight and increases stiffness.
-
Page 5: Geometry
GEOMETRY FOX 32 / 120MM FORK 15.0 16.5 17.5 19.0 20.5 21.7 22.7 23.7 25.7 25.7 68.0 68.0 69.1 69.1 69.1 72.0 72.0 72.0 72.0 72.0 17.3 17.3 17.5 17.5 17.5 42.2 43.3 44.5 45.5 46.5 13.0 13.0 13.0 13.0 13.0 28.7 28.7... - Page 6 KEEP YOUR YETI FRESH AND CLEAN OVERVIEW TORQUE Following these guidelines will help maintain the performance of your bicycle and prevent Yeti recommends using a torque wrench when assembling your frame. Torque specifications more serious problems from arising. It is important to remember that service intervals can vary for individual parts on the ASR-C are listed below, as well as in the step by step assembly depending on climate, trail conditions and riding frequency.
-
Page 7: Shock Setup
SHOCK SETUP YETI TIPS TOOLS NEEDED Inspect your shock for any visible damage. • Shock Pump If oil is leaking or you notice any damage to • Tape Measure the surfaces or seals, please contact the Fox Racing Shox service center for repair at 800. FOX.SHOX. -
Page 8: Quick Start Guide
SHOCK SETUP 04. COMPRESSION DAMPING 05. TRAIL ADJUST The compression damping has three levels of The trail adjust dial controls the “trail” mode low adjustment and is controlled by the blue lever speed compression adjustment. It has three on the shock. The “climb” mode engages the levels of adjustment and is controlled by the firmest low-speed compression setting for black dial on the shock body. - Page 9 CABLE SETUP 03. REAR DERAILLEUR YETI TIPS Measure the appropriate amount of shifter housing. There are going to be two segments; one from the handlebar to the top housing stop port and one from the bottom housing stop port to the rear derailleur. uses internal routing for the derailleurs.
- Page 10 Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti Dealer Using the Fox guide pin, insert the female upper Prep male bolt with blue (248) Loctite.
- Page 11 ASSEMBLY ASSEMBLY Loosely thread the male bolt into the upper link Finish tightening the upper link pivot using a well Slide the main pivot axle into the swingarm Thread the main pivot axle in using a 10mm allen pivot pin on the frame. Do not overtighten. calibrated torque wrench set to 5 Nm through the non drive side.
- Page 12 ASSEMBLY ASSEMBLY Use a Fox guide pin to align the link, spacers and Slip the front shock mount into the front triangle Using the guide pin slide the front shock Apply blue (248) Loctite to the male bolts for the the swingarm.
- Page 13 ASSEMBLY Prep your collet bolt with grease. Thread the collet bolt into the main pivot axle. Using a well calibrated torque wrench, torque to 13.5 Nm. Torque to 13.5 Nm The completed ASR-Carbon frame. Now put some parts on it and go for a ride!
-
Page 14: Exploded View
EXPLODED VIEW GREASE LOCTITE... -
Page 15: Rebuild Kits
EXPLODED VIEW PARTS LIST ITEM# PART # DESCRIPTION ITEM# PART # DESCRIPTION ASR-C FRONT TRIANGLE 300030288 STUD YETI TI FEMALE 8.0OD X 54MM, M6 300070006 ICE AXE HEAD BADGE 300030150 BOLT YETI TI FEMALE 8.0OD X 36.5MM, M6 300060072 YETI SEAT CLAMP STANDARD 300030249 BOLT YETI TI FEMALE 8.0OD X 31.5MM, M6 300020045... - Page 16 REBUILD KITS CONTINUED PART # DESCRIPTION PART # DESCRIPTION 200020222 ASR-C MASTER REBUILD KIT 200020223 ASR-C HARDWARE KIT 300020045 BEARING F6902 2RS 28X15X7 OUT 300020047 SPACER 8MM X 4.5MM FOR SHOCK 300020047 SPACER 8MM X 4.5MM FOR SHOCK 300030062 WASHER SS 6.5MM ID 12.5 OD .5M 300030069 WASHER SS 8.8MM ID 12.5MM OD .
-
Page 17: Warranty
YETI frameset. Yeti Cycles will repair or replace, at its option, any of the above listed frames it determines to be defective due to defective materials and/or workmanship. The (5) five year limited warranty...