Overview welcOme tO the tribe Congratulations on your purchase of a new Yeti bicycle and welcome to the Yeti Tribe. We are confident your new bicycle will exceed your expectations for value, performance and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience.
Frame Features full carbOn frame The front and rear triangles are constructed entirely of hand-laid carbon fiber with co-molded aluminum lugs at the bearing and pivot connections. bOttOm bracket The bottom bracket is a press-fit-style instead of the traditional threaded cups. This reduces weight and adds another level of stiffness.
Geometry Ge O met r Y a s-r car bO n 120 mm fOrk 18.0 19.0 21.0 22.6 23.6 24.6 16.9 16.9 16.9 42.8 43.8 44.9 13.0 13.0 13.0 27.8 27.8 28.1 19.33 19.33 19.33 1.54 1.54 1.54 100 mm fOrk 18.0 19.0 21.0...
maintenance? If you are having trouble with any of the maintenance tasks that need to be performed contact your local dealer or visit www.parktool.com and check out the repair help section. This section contains detailed instruction on many of the service items listed in the maintenance schedule.
Bike Setup tOOls neeDeD Shock Pump Tape Measure time 15-20 minutes Yeti tips Inspect your shock for any visible damage. If oil is leaking or you notice any damage to the surfaces or seals, please contact the Fox Racing Shox service center for repair at 800.FOX.SHOX. Shock set-up can fluctuate greatly based on the rider.
Quick Start Guide Setup-Fox RP23 air pressure The main air spring controls the sag of the shock. quick start GuiDe rp23 as-r carbOn For the 575 to ride properly it is important to setup the shock with the air sprinG settinGs correct amount of sag.
Page 9
bOlt-On cable GuiDes 2011 Yeti frames use bolt-on cable guides for routing brake and shift housing. The guides allow for clean cable routing and thier two-piece design keeps the housing from contacting the frame and marring the finish. Line Setup The AS-R has full cable housing.
It is also important to prep all bolt threads. The instructions denote whether to use a blue Loctite compound or grease. Warning: Service on Yeti bicycles requires special knowledge and tools. Yeti Cycles recommends that all service and repairs be performed by an authorized Yeti dealer. assemblY...
Page 11
threaD prep Yeti recommends prepping all threads with Loctite or grease. The medium strength (blue) formula along with proper torque is ideal for keep the bolts snug. Assembly DOGbOne & shOck setup Press bearings flush into the bottom of DOGbOne anD shOck mOuntinG assemblY Install the dogbone the dogbone with shoulder facing out.
Assembly Cont. Disassembly Tips mOuntinG rear trianGle Place a 46.5mm Ti female bolt over the rear trianGle DisassemblY At the seatstay junction, remove the male portion of the Fox guide pin. Use a dead blow hammer to push Ti male bolt from the 46.5 female bolt with a 5mm allen key. the bolt into place.
Chip System installinG shimanO DrOpOut kit Fit the 12MM insert derailleur The 2011 AS-R Carbon features our Yeti Chip System that allows for the use of a standard 135mm QR or a hanger into the groove on the inside of the drive side chainstay. The 12mm x 142mm thru axle.
rebuilD kits The individual components of each Yeti bike are not sold separately. All yeti parts are sold in rebuild kits listed below. Each and every part can be obtained by purchas- ing one of the rebuild kits. Cross reference the part number you desire from the parts list to the rebuild list.
Yeti frameset. Yeti Cycles will repair or replace, at its option, any frame it determines to be defective materials and / or workmanship. The (2) two year limited warranty is conditioned upon the bicycle being ridden under normal Disclaimer conditions and having been properly maintained.