Table of Contents
Advertisement
6.14. Service function / readout of fault memory and single actuator selection:
General information
w Calling the service function is executed in all designs
resp. key arrangements analogously.
w For that you always have to use keys S0, S1, S2 and S3
independent of their variant-depending program load.
w In the service function mode key S1 is ALWAYS
responsible for the function "readout of fault memory"
and "single actuator selection"
EDW 1503 / VGA
LD1
LD2
LD3
1 99
S1
S3
It is generally valid:
For calling all service functions you always have first to
actuate function keys S1 and S3 before switching on
the applianceby ON/OFF switch S0.
The keys have to remain pressed about 3 seconds
to activate the function.
This procedure is intentionally different to that for the
customer functions.
Calling above-mentioned service function
1.
LD1
LD2
LD3
LD4
LD5
LD6
S1
S2
S3
S4
S5
S6
2.
S1
S3
3.
S1
S3
3-4 Sekunden
alle blinken
LD1
LD2
LD3
S0
4.
S1
S3
Display und LED blinken
LD1
5.
1 0
S1
I 0
LD1
Anzeige 2. + 3.Fehlers
Display und LED blinken
I 0
pro Tastendruck
1 Weiterschaltung
4
S1
5
Codierte Anzeigen
der Einzelaktoren
10
Display und LED blinken
LD1
6.
1 0
S1
LD1
LD2
LD3
LD4
LD5
LD6
... AUS nach 60sek. automatisch
... AUS durch manuelle Betätigung über Ein/Aus
34
Calling the functions
LD10
LD11
"readout of fault memory" and "single actuator selection"
LD12
S0
1.
Appliance in switched-off condition
2.
Press keys S1 and S3 simultaneously and ...
3. / 4. ... and switch on the appliance by ON/OFF switch S0.
For that keep pressed keys S1 and S3 until the 3
confirmation LEDs LD1, LD2 and LD3 are flashing.
( A temporary flashing up of LEDs is possible and no fault!)
S0
5. / 6. By actuating the function key S1 you now can call the function.
The confirmation LED LD1 continues flashing, LEDs LD2 and
LD3 go out.
The first value of the fault memory is indicated in the display.
S0
The display indication is flashing.
By any further actuation of the function key S1 it is possible
to call the next step and indicate it in the display as follows.
2. actuation: Display of second value of the fault memory
3. actuation: Display of third value of the fault memory
4. actuation: Display "4" - selection of regeneration valve
5. actuation: Display "5" - selection of drain pump
6. actuation: Display "6" - selection of valve
7. actuation: Display "7" - selection of heating
8. actuation: Display "8" - selection of circulation pump
9. actuation: Display "9" - selection of detergent dispenser
10.actuation: Display "10" - selection of drying fan
(see description page B 19 / "Survey of fault displays")
All positions can be called scrolling as many time as one wants.
The several steps are switched onward manually by pressing
any key. If the function key S1 is not pressed within 60 seconds,
the service function is left automatically. All LEDs of the
S0
program and option keys are lit. The indication in the display
goes out. The appliance is in the "prestart" mode again.
It is also possible to leave the function by switching off the
appliance by ON/OFF key S0.
S0
(filling to level - if level already existing, no filling)
(only when level detected)
Advertisement
Table of Contents
