Electrolux EDW 1506 Service Manual page 31

6.11. Service function / setting of water hardness
General information
w Setting and changing the water hardness area is executed in
all designs resp. key arrangements analogously.
w For that you always have to use the keys S0, S1, S2 and S3
independent of their variant-depending program load.
w Key S1 is ALWAYS the "water hardness area key"
w The water hardness area value 4 is preset by the manufacturer.
With setting "1L" it is generally not regenerated.
A salt addition is not necessary.
w A possibly existing "salt" LED is not selected.
Electronic and mechanical setting with the appliance:
w In addition to the "electronic" setting on the control panel
described on the right you also have to pay attention to the
mechanical setting in the appliance by the 2-step blending
switch. (see for that the table for hardness area values)
EDW 1503 / VGA
LD1 LD2 LD3
1 99
S1 S2 S3
Table for hardness area values:
Anzeige Anzeige Einstellung der
Wasserhärte
Display Ende-LED Härtestufe
elektr.. mech. in dH
Anzahl blinken
1L 1 mal 1 bis 4
2L 2 mal 2 4 bis 10
3L 3 mal 3 11 bis 14
0
4L 4 mal 4 15 bis 18
5L 5 mal 19 bis 22
5
6L 6 mal 6 23 bis 28
7L 7 mal 7 29 bis 36
8L 8 mal 8 37 bis 42
1
9L 9 mal 9 43 bis 50
10L 10 mal 51 bis 70
10
Calling / changing / saving the "electronic" hardness area value
1.
2.
3.
4.
4L
5L
Verschneide-
6L
schalter
10L
1L
S0
LD1 LD2
... AUS nach 60sek. automatisch
Bemerkung
in mmol/L Bereich
bis 0,7 I kein Regenerieren
0,7 bis 1,8 I / II
1,9 bis 2,5 II
2,6 bis 3,2
... AUS durch manuelle Betätigung über Ein/Aus
III
3,3 bis 3,9
4,0 bis 5,0
5,1 bis 6,4
6,5 bis 7,5 IV
7,6 bis 8,9
9,0 bis 12,5
doppelt Regenerieren
LD1 LD2 LD3 LD4 LD5 LD6
LD10
LD11
LD12
S1 S2 S3 S4 S5 S6
S0
LD1
LD2 LD3 LD4 LD5 LD6
S0
blinken
LD1 LD2 LD3
S2 S3
blinkt
LD1
S1
LD1
blinkt
Pro
Tastendruck
S1
+ 1 Stufe
Ausgabe
zusätzlich
akustisch
LD3 LD4 LD5 LD6
S0
S0
31
When calling the customer functions no washing cycle
must be selected generally!
Calling the function "set water hardness"
1. Appliance in switched-off condition
2. Switch on appliance with ON/OFF key S0 -- "prestart" mode
Ä All LEDs of the program and option keys are lit.
3. Press keys S2 and S3 simultaneously until the
confirmation LEDs LD1, LD2 and LD3 are flashing.
3. By actuating the function key S1 you now can call the
water hardness function. The confirmation LED LD1
continues flashing, LEDs LD2 and LD3 go out.
The set hardness area is indicated in the display and in
addition acoustically.
( see for that the table on the left side of this page! )
Changing the set hardness
Any other actuation of the function key S1 changes
the hardness area. This increases the value scrolling.
( 4L - 5L - 6L - ... - 10L - 1L - 2L - ... )
Leaving the function
After the last key pressure of function key S1 you can
leave the special program as follows.
After 60 seconds all LEDs of the program and option keys
are lit automatically. The indication in the display goes out.
The appliance is in the "prestart" mode again
or
the appliance is switched off by the ON/OFF key S0.
Saving the set water hardness
The selected hardness area is saved directly after
any entry.