Table of Contents
Advertisement
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well, Wait for 15 seconds:
a. If the engine still running.
I. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
II. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3
parking light flashes for confirmation.
b. If the engine shut down after the vehicle has been started.
I. Press the
button twice on the transmitter to turn ignition lights "OFF".
II. Press
button on the transmitter to set "Check Level" to LOW position. [1] LED flash,
[1] chirp to confirm this setting
III. Repeat the step1 – 2.
3. If the crank time is too long, (Engine is successfully running, while the starter is still cranking):
a. Press the
button twice on the transmitter to stop engine running.
b. Press
button on the transmitter to set proper "Start Timer". The chirp & LED pause will confirm this
enter. (Decrease "Start Timer" is necessary.)
c. Repeat the step1 – 4.
4. If the crank time is too short, (The engine did not successfully run before the starter quit cranking):
a. Press the
button twice on the transmitter to turn ignition lights "OFF".
b. Press
button on the transmitter to set proper "Start Timer". The chirp & LED pause will confirm this
enter. (Increase "Start Timer " is necessary.)
c. Repeat the step1 – 4.
ENGINE CHECKING OFF
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
hearing and the LED start to flash then release the valet switch.
3. Press the transmitter
flash, [3] chirp to confirm this setting
Once you complete step 3, you can adjust and test "Start Timer" as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well:
a. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
b. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
3. If the crank time is too long, (Engine is successfully running, while the starter is still cranking):
a. Press the
button twice on the transmitter to stop engine running.
b. Press the
button on the transmitter to set proper "Start Timer". The chirp & LED pause will confirm
this enter. (Decrease "Start Timer" is necessary.)
c. Repeat the step1 – 4.
4. If the crank time is too short, (The engine did not successfully run before the starter quit cranking):
a. Press the
button twice on the transmitter to turn ignition lights "OFF"
b. Press
button on the transmitter to set proper "Start Timer". The chirp & LED pause will confirm
this enter. (Increase "Start Timer " is necessary.)
c. Repeat the step1 – 4.
RETURN TO FACTORY DEFAULT SETTING:
1. Turn the ignition ON then OFF 3 TIMES and stay in OFF position.
2. Push the Valet switch 12 times and holding in on the 12
hearing and the LED start to flash then release the valet switch. You are now in the "Return To Factory
Default Setting" programming mode.
ALARM FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:
3. Press the transmitter
six chirp with 3 long chirp and the LED turns On for 2 seconds to confirm the system "Alarm Feature I &
II Programming all returns to factory default setting.
START FEATURE ALL RETURNS TO FACTORY DEFAULT SETTING:
4. Press
button first, within 3 seconds press and hold the
seconds, there will be a confirmation six chirp with 3 long chirp and the LED turns On for 2 seconds to
confirm the system "Start Feature I & II Programming all returns to factory default setting.
VS 255 INSTALL
and
buttons at the same time to set the "Engine Checking Off". [3] LED
and
buttons at the same time for 5 seconds, there will be a confirmation
15
th
push until five chirps with a long chirp is
th
push until Six chirp with a long chirp is
and
buttons at the same time for 5
Advertisement
Table of Contents
