Viking VS 255 Installation Manual page 12

2. Push the Valet switch 2 times and holding in on 2
the LED start to flash then release the Programming switch. You are now in the feature 'I' programming
mode.
3. Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.
a. The horn chirps and LED pause will indicate newly setting.
b. The factory default settings is always [2] LED flash, [2] horn chirp.
4 Depress the transmitter button 'A' again to change the feature. Simple keep re-depressing the
transmitter button 'A' again until the module advances to your desired setting.
a. In this case, Press button 'A' again, the module would advance to [2] LED flash, [2] horn chirp.
b. Press button 'A' again, the module would advance to [3] LED flash, [3] horn chirps etc.
5. Depress the transmitter button 'B' corresponding to the feature 'B' you wants to program.
Press One Chirp / LED one pulse
Transmitter Factory Default Setting
Button
Chirps on
1
Pathway illumination feature
2
"off"
H5/4 Pink Wire = 2-Step
3
Door Unlock Output
H2/4 Brown Wire = Horn
4
Output
+
H5/3 White Wire = Dome
5
Light Output
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Ground Output During Start (Crank) = This wire will provide a 200mA ground output while the starter
output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire
found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.
ALARM FEATURE "
1 Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2 Push the Valet switch 4 times and holding in on the 4
and the LED start to flash then release the valet switch. You are now in the Alarm feature 'II'
programming mode.
3 Press and release the transmitter button 'A' corresponding to the feature 'A' you want to program.
Press One Chirp /
T r LED one pulse
ransmitte
Button Factory Default
Setting
0.8-second Door
1
lock pulses.
Ignition controlled
2
door locks & unlocks
Door lock before
3
start
4 H6/1 Green Wire =
1 Pulse Remote
Start
Exit
: Turn Ignition to 'ON' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
Comfort Feature:
VS 255 INSTALL
Two Chirps / LED two pulse
Chirps off
Parking light "on" for 30-
second upon an unlock
signal
H5/4 Pink Wire = Factory
Security Disarm Signal
Output
H2/4 Brown Wire = Channel
4 Output
H5/3 White Wire = Channel
4 Output
II
" PRORAMMING:
Two Chirps /
LED two pulse
3.5-second Door
lock pulse.
Ignition controlled
door locks only
Door lock after
shut-down
H6/1 Green Wire =
3 Pulse Remote
Start
nd
push until one chirp with a long chirp is hearing and
th
push until two chirps with a long chirp is hearing
Three Chirps /
LED three pulse
Double pulse unlock
Ignition controlled
door unlocks only
Door lock before
start and Door lock
after shut-down
12
Three Chirps / LED three
pulse
Parking light "on" for 30-
second upon an unlock
signal & 10-second upon a
lock signal.
H5/4 Pink Wire = Start
Status (Shock Sensor
Bypass Control) Output
H2/4 Brown Wire = Rearm
Signal Outpu
t
H5/3 White Wire = Ground
Output During Start (Crank)
Four Chirps /
LED four pulse
Door lock with
"Comfort Feature"
Without ignition
controlled door locks
& unlocks
Without this feature