Table of Contents
Advertisement
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
5 WIRE ALTERNATING DOOR LOCKS
H5/4:
+ 12V
87
5-Pin
86
Plug
Pink Wire
87A
85
FromA
larm
30
Green Wire
Cut the Unlock Wire
H8:
85
3 Pin
87
Plug
87A
30
To
Alarm
86
85
30
87
87A
86
Blue Wire
OEM Driver's
Door Lock Motor
X
Cut Existing Unlock
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
GROUND SWITCHED DOOR LOCKS
H5/4:
5-Pin
Pink Wire
Plug
FromA
larm
Existing Neg.
Unlock Wire
Green Wire
Door Lock
87
H8:
Blue Wire
3 Pin
Door Unlock
86
Plug
87A
To
Alarm
30
OEM
Door Lock
Motor
Cut Existing Unlock
A. PROGRAMMING THE REMOTE TRANSMITTER:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing and the LED start
to flash then release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp/ a flash
from parking light / the LED turns on for 2 seconds indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to
confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE "
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
VS 255 INSTALL
OEM Door Master Lock
+12V
Unlock
Lock
x
X
Cut the Existing
Lock Wire
+ 12V
OEM Slave
Door Lock
Switch
Unlock
Lock
+12V
To All Other
Door Lock
Motors
OEM Door Master Lock Switch
Unlock
Lock
Existing Neg.
Lock Wire
85
OEM Door
Lock Relay
+ 12V
X
To All Other
Door Lock
Motors
PROGRAMMING
I
" PRORAMMING:
VACUUM OPERATED DOOR LOCKING SYSTEM:
TYPICAL OF MERCEDES BENZ AND AUDI.
Locate the wire under the driver's kick panel. Use the
voltmeter connecting to ground, verify that you have th
correct wire with the doors unlocked, the voltmeter will
receive "12 volts". Lock the doors and the voltmeter wi
read "0 volt". Move the alligator clip to +12V and the
voltmeter will receive "12 volts". Cut this wire and mak
connections. Be sure to program door lock timer to
3.5 seconds.(See Alarm Feature
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
POSITIVE SWITCHED DOOR LOCKS
+12V
H5/4:
5-Pin
87
Pink Wire
Plug
FromA
86
87A
larm
30
Blue Wire Door Lock
H8:
Green Wire
87
3 Pin
Door Unlock
87A
Plug
86
To
Alarm
30
OEM Driver's
Door Lock
Motor
Cut Existing Unlock
11
II – 1
Programming.)
OEM Door Master Lock Switch
Unlock
Lock
85
Existing Pos.
Unlock Wire
+ 12V
Existing Pos.
Lock Wire
+ 12V
85
OEM Door
Lock Relay
X
To All Other
Door Lock
Motors
Advertisement
Table of Contents
