Table of Contents
Advertisement
RPM learning
3
Start Timer:
0.6-second
4
Low check level for
"Engine Checking
TACH" mode or
Hi check level for
"Engine Checking
Voltage" mode
-
Start / Stop the system for TESTING & ADJUSTMENT
5
Exit
: Press the
button on the transmitter. A 3 long chirps & 3 parking light flashes to confirm exit.
ENGINE CHECKING TACH. / RPM LEARNING
Important Note: You must program the "Tach Signal" before trying to remote start.
1. Turn the Ignition switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and hold it until five chirps with a long chirp is hearing and the LED start
to flash then release the valet switch.
3. Press and release the transmitter
Checking TACH.". [1] LED flash, [1] chirp to confirm this setting.
4. Press and release the transmitter
5. Start the vehicle with the key. (While the engine is running, the parking light & LED will flash, If don't,
please check tachometer White/Red wire connection. (H6/5)
6. Press and hold the valet switch for 2 seconds until a long chirp and the LED / the parking light will
constantly on for two seconds. The RPM signal is learned.
7. Turns off the ignition switch to stop engine running.
Once you complete step 7, you can adjust and test "Check Level" as below:
CHECK LEVEL PROGRAMMING: (TEST and ADJUST)
1. Press the
button twice on the transmitter to start the vehicle.
2. If everything goes well:
a. Press the
button twice on the transmitter to stop engine running. You have been completed this
programming successfully.
b. Press
button on the transmitter to exit the program mode. There will be 3 long chirps & 3 parking
light flashes for confirmation.
3. If the crank time is too short, (The engine did not successfully run before the starter quit cranking):
a. Press the
button on the transmitter to turn ignition lights "OFF".
Press
button on the transmitter to set proper "Check Level " to Hi position. [2] LED flashes,
[2] chirps to confirm this setting
b. Repeat the step1 – 4.
4. If the crank time is too long, (Engine is successfully running, while the starter is still cranking):
a. Press the
button on the transmitter to stop engine running.
Press
button on the transmitter to set proper " Check Level " to Low position. [1] LED flash,
[1] chirp to confirm this setting
b. Repeat the step1 – 4.
ENGINE CHECKING VOLTAGE
Important Note: The voltage "Check Level" for most vehicles would be set in "Hi Check Level", while in
"Engine Check Voltage" mode, the "Check Level" must be set at "HI" position first.
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 10 times and holding in on the 10
hearing then release the valet switch.
3. Press the transmitter
LED flashes, [2] chirps to confirm this setting.
4. Press
button on the transmitter to set "Check Level" to "HI" position. [2] LED flashes, [2] chirps to
confirm this setting.
Once you complete step 4, you can adjust and test "Start Timer" as below:
START TIMER PROGRAMMING: (TEST and ADJUST)
VS 255 INSTALL
Hi check level for
"Engine Checking
TACH" mode or
Low check level for
"Engine Checking
Voltage" mode
and
buttons at the same time once to set the "Engine
button once, [1] LED flash, [1] chirp to indicate your are in features
and
buttons at the same time to set the "Engine Checking Voltage". [2]
14
0.8-second (2 chirps), 1.0-second (3
chirps), 1.2-second (4 chirps), 1.4-second
(5 chirps), 1.6-second (6 chirps),
1.8-second (7 chirps), 2.0-second (8
chirps), 3.0-second (9 chirps), 4.0-second
(10 chirps),
th
push until five chirps with a long chirp is
Advertisement
Table of Contents
