Kirisun PT4208 Instruction Manual
Fm handheld transceiver
Hide thumbs
Also See for PT4208:
- Service manual (53 pages) ,
- Instruction manual (22 pages) ,
- Instruction manual (22 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kirisun PT4208
Summary of Contents for Kirisun PT4208
-
Page 1: Instruction Manual
INSTRUCTION MANUAL PT4208 FM HANDHELD TRANSCEIVER... - Page 2 INSTRUCTION MANUAL PT4208 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand two- way radios produced by Kirisun Electronics (Shenzhen) Co., Ltd. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work;...
- Page 3 areas or on unstable surfaces. Do not modify this radio for any reason. Refer service to qualified licensed or certificated technicians only. Notice to the User: Government laws prohibit radio communication without permission in government districts. Illegal operation is subject to punishment by fine and/or imprisonment.
-
Page 4: Table Of Contents
If the radio emits smoke or strange odors, turn it off and remove 2.5. Install the belt clip..............6 the battery from the radio and promptly contact your local authorized 3.Radio Overview................6 Kirisun dealer. 4.Basic Operation................7 5.Programmable Key Function............8 6.Auxiliary functions................10 6.1.Time-out Timer...............10... -
Page 5: Preparation
1. Package-opened Inspection Preparation Please check the host in the package and the supplied accessories 2.1 Charge the battery in the following table before using. Any articles are found lost or Insert the cable of the power adaptor damaged, please contact the distributor without delay. into the adaptor jack at the back of the charger, insert the power adaptor Supplied Accessories... -
Page 6: Install/Remove The Battery
Both KB-70A nickel-hydrogen battery and KB-70B Li-polymer batt- -ery of the company are applicable to this radio. Press the upper end of the battery After being purchased or before the first charging after being laid down till the push button on the radio aside for a long time (2 months), the battery can reach its normal completely bounce out and locked. -
Page 7: Install External Speaker/Mic
2.4 Install external speaker/MIC Turning to select channels 1-16. Open the soft rubber cover of external speaker or MIC with your finger- .Power/Volume knob -nail, insert the pin of matching external speaker or MIC into the pinhole Turn clockwise to turn on the radio, keep turning to adjust the of the radio. -
Page 8: Programmable Key Function
. Channel: mode. Turn the channel selector knob to select 3.Call Key 1 Sends the DTMF/2Tone code assigned to the required channel. When the correct signal call 1 key. is received, you can hear sounds from the 4.Call Key 2 Sends the DTMF/2Tone code assigned to speaker. -
Page 9: Auxiliary Functions
b)After the alarm, when the time of transmission exceeds the preset press again to resume normal operation. time, the TOT timer will act. 14.Squelch off Press to enable squelch and release to resume 4) TOT reset time: normal operation. momentary a)Limiting the time delay from the PTT key is loosened to the timer 15.Squelch off Hold this key to open the squelch. -
Page 10: Ctcss /Dcs
When changing the channel with the channel selector, after the 6.8 Scan channel is changed, the radio will announce the number of the The radio can be programmed to scan multiple channels to channel selected. receive signals from them. 6.8.1 Start/End Scan Function 6.5 CTCSS /DCS a) Press the key programmed to Scan , the Scan function is... -
Page 11: Transmission Begin And Transmission End Signals (Ptt Id)
If Transmission End has been set, when you release the PTT switch, status, it will transmit signals from the current channel, otherwise, the ID signals will be transmitted. it will transmit signals from the channel where the scan is started. If both have been set, the ID signals will be transmitted respectively Priority channel: The priority channel preset in the Scan list. -
Page 12: Wired Clone
7. Wired Clone Mode B. The crystal X4 of phase lock loop is If the wired clone function is enabled, the radio will not quit after broken. Please change it. entering the wired clone mode. To return to normal user mode, the C. -
Page 13: Major Specifications
PT4208 OF CONFORMITY General Specifications 0678 Frequency 136~174MHz, 400~450MHz, We, Kirisun Electronics(Shenzhen) Co., Ltd. 420~470MHz, 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, China Channel Number Channel Spacing 12.5kHz(N)/25kHz(W) Declare on our sole responsibility that this equipment complies with External Dimension (HXWXD) 119mm*54.5mm*34mm... - Page 14 NOTE NOTE...