Troubleshooting - Breville BOV845 Smart Oven Pro Instruction Book

TROUBLESHOOTING

POSSIBLE PROBLEM EASY SOLUTION
• Check that the power plug is securely inserted into the outlet.
• Insert the power plug into an independent outlet.
Oven will not switch "ON"
• Insert the power plug into a different outlet.
• Reset the circuit breaker if necessary.
• The oven will remember the last setting used for each function
unless you remove the plug from the power outlet.
I would like to have the oven
• To restore the oven's default settings for each function, remove
LCD default settings back
the plug from the power outlet. Wait 5 seconds, then plug back
in.
• The oven goes into standby mode if not used for 10 minutes.
When in standby mode, the LCD screen will cease to
illuminate, however all function options will still be visible.
The LCD display light has
gone out
• To re-activate the oven out of standby mode, press the START/
CANCEL button on the control panel, or turn any dial. The
LCD screen will re-illuminate.
• Some large pizzas may brown unevenly in compact ovens.
The pizza does not cook
Open the oven door half way through the cooking time and
evenly
turn the pizza 90 degrees for more even darkness.
The Magnetic Auto-Rack
• Always open the door slowly and in a controlled manner when
Eject comes out too far when
the wire rack is inserted into the middle rack height position
to prevent the wire rack from ejecting too quickly.
I open the door
I cannot select the FROZEN
• The FROZEN FOODS button is only selectable during the
FOODS button TOAST, BAGEL, PIZZA and COOKIES functions.
Steam is coming out from the
• This is normal. The door is vented to release steam created
top of the oven door from high-moisture content foods such as frozen breads.
• Element IQ
The heating elements appear
pulsing the power in the heating elements in short bursts. This
to be pulsing
is normal.
• This is normal. The condensation created from high moisture
Water is dripping onto
content foods such as frozen breads will run down the inside of
counter from under door
the door and can drip onto the counter.
• To ensure the measurements are standardized, the oven
temperatures have been calibrated in the TOAST position
The temperature reading
(center of the middle rack with no tray in place). Re-check the
on the LCD screen doesn't
temperature in this position, ensuring not to open the oven
match the temperature
door for 10 minutes as heat will escape each time the door
measured inside the oven.
is opened. Note that the 'preheat' alert sounds at 75% of the
target temperature.
28
‰
accurately controls the heat inside the oven by
TROUBLESHOOTING
POSSIBLE PROBLEM EASY SOLUTION
• The 'preheat' alert sounds at 75% of the target temperature.
This provides the fastest, combined preheating and cooking
time.
• This is because when the 'preheating' alert sounds, signaling
the user to open the oven door and insert food, there is
dramatic temperature loss inside the oven. If the alert sounded
at 100% of the target temperature, opening the door would
The 'preheat' alert sounds
mean a lot of this waiting time is "wasted". We have calculated
that by sounding the alert at 75% of the target temperature,
at a lower temperature than
followed by the oven door being opened to place food inside
what is displayed on the LCD
the oven, that we still recover to the target temperature up to 2
screen.
minutes faster. This is why the temperature on the LCD screen
does not match the target temperature at the 'preheat' alert.
In total, it takes the oven approximately 8–10 minutes from
start-up, including opening the oven door when the 'preheat'
alert sounds, to reach the target temperature. To ensure the
fastest heat up time, the Breville oven uses the maximum
allowable power from the outlet (1500W for baking, 1800W
for toasting).
• The LCD screen will display 'E01' when there is a non-
The LCD screen
resettable issue with the appliance. Should this occur,
displays 'E01' immediately remove the power cord from the power outlet
nd call Breville Consumer Support.
• The LCD screen will display 'E02' when there is a non-
The LCD screen displays
resettable issue with the appliance. Should this occur,
immediately remove the power cord from the power outlet
'E02'
and call Breville Consumer Support.
• The LCD screen will display 'E03' if the oven temperature is
above the set maximum limit. Remove the plug from the power
The LCD screen displays
outlet, allow the oven to cool for 15 minutes, then plug back in.
'E03'
• Call Breville Consumer Support if the 'E03' message
continues.
• The LCD screen will display 'E04' if the room temperature is
The LCD screen displays
below the set minimum. Unplug the oven and relocate to a
'E04'
warmer area.
• The LCD screen will display 'E05' when there is a non-
The LCD screen displays
resettable issue with the appliance. Should this occur,
'E05' immediately remove the power cord from the power outlet
and call Breville Consumer Support.
29