HP StoreEasy 1000 Storage Administrator Guide This document describes how to install, configure, and maintain all models of HP StoreEasy 1000 Storage and is intended for system administrators. For the latest version of this guide, go to http://www.hp.com/support/StoreEasy1000Manuals. HP Part Number: B7D88-96134...
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents 1 HP StoreEasy 1000 Storage.................6 Features..........................6 Hardware components......................6 HP StoreEasy 14x0 Storage hardware components..............6 HP StoreEasy 15x0 Storage hardware components..............9 HP StoreEasy 16x0 Storage hardware components..............11 HP StoreEasy 18x0 Storage hardware components..............14 Drive LED definitions......................16 Systems Insight Display LED combinations................17 Software components......................18...
File system elements......................56 File sharing elements......................57 Volume Shadow Copy Service overview................57 Using storage elements.......................57 Network adapter teaming......................57 Management tools........................57 HP Systems Insight Manager....................57 Management Agents......................58 5 File server management................59 File services management......................59 Storage management utilities....................59 Array management utilities.....................59 Array Configuration Utility....................59 Disk Management utility....................60...
6 Troubleshooting, servicing, and maintenance..........83 Accessing Event Notifier Configuration Wizard................83 Maintaining your storage system....................83 Determining the current storage system software version...............84 HP System Management Homepage..................84 Starting the System Management Homepage application............85 System Management Homepage main page.................85 Certificate of Authenticity......................87 Known issues.........................87 Verifying services are running....................90...
This section provides illustrations of the storage system hardware components. HP StoreEasy 14x0 Storage hardware components The following figures show components and LEDs located on the front and rear panels of the HP StoreEasy 14x0 Storage. Figure 1 HP StoreEasy 14x0 Storage front panel components 1.
Figure 2 HP StoreEasy 14x0 Storage front panel LEDs and buttons Item Description Status UID LED/button Blue = Identification is activated. Flashing blue = System is being managed remotely. Off = Identification is deactivated. Power On/Standby button and system Green = System is on.
7. Serial connector 8. Video connector 9. USB connectors 10. NIC 1/shared iLO management connector 1 1. NIC connector 2 Figure 4 HP StoreEasy 14x0 Storage rear panel LEDs and buttons Item Description Status NIC link LED Green = Link exists...
HP StoreEasy 15x0 Storage hardware components The following figures show components and LEDs located on the front and rear panels of the HP StoreEasy 15x0 Storage. Figure 5 HP StoreEasy 15x0 Storage front panel components 1. Optical drive (optional) 2. Media drive bay 3.
Amber = System is in standby, but power is still applied. Off = Power cord is not attached or power supply failed. Figure 7 HP StoreEasy 15x0 Storage rear panel components 1. Non-hot-plug power supply 2. Slot 4 PCIe x16 (8, 4, 1) 3.
Power supply failed Power supply is in standby mode Power supply error HP StoreEasy 16x0 Storage hardware components The following figures show components and LEDs located on the front and rear panels of the HP StoreEasy 16x0 Storage. Hardware components...
Figure 9 HP StoreEasy 16x0 Storage front panel components 1. Video connector 2. LFF drives 3. USB connector Figure 10 HP StoreEasy 16x0 Storage front panel LEDs and buttons Item Description Status NIC status LED Green = Linked to network...
12. Video connector 13. USB connectors 14. iLO 4 connector HP StoreEasy 1630 Storage Slot 2 PCIe3 x16 (8, 4, 1) (P822) HP StoreEasy 1640 Storage Slot 3 PCIe3 x8 (P822) Figure 12 HP StoreEasy 16x0 Storage rear panel LEDs and buttons...
Power supply exceeded current limit HP StoreEasy 18x0 Storage hardware components The following figures show components and LEDs located on the front and rear panels of the HP StoreEasy 18x0 Storage. Figure 13 HP StoreEasy 18x0 Storage front panel components 1.
Flashing Green = Power On/Standby Button has been pressed; system is waiting to power on. Solid Green = System on Figure 15 HP StoreEasy 18x0 Storage rear panel components 1. PCIe slots 1–3 (top to bottom) 2. PCIe slots 4–6 (top to bottom) 3.
Off = No activity exists NIC link LED Green = Link exists Off = No link exists Drive LED definitions The following figure shows the drive LEDs. These LEDs are located on all HP ProLiant hot plug hard drives. HP StoreEasy 1000 Storage...
Figure 17 Drive LEDs Item Status Definition Locate Solid blue The drive is being identified by a host application. Flashing blue The drive carrier firmware is being updated or requires an update. Activity ring Rotating green Drive activity No drive activity Do not remove Solid white Do not remove the drive.
Power is available. NOTE: For more information on troubleshooting, refer to the hardware platform information. The following list identifies the ProLiant model for each HP StoreEasy 1000 Storage product: 1440: ProLiant DL360e Gen8 1550: ProLiant ML310e Gen8 v2 1640: ProLiant DL380e Gen8...
GUI mode by default. You can switch to Server Core Installation mode; however, Server Core Installation mode is only supported on an HP StoreEasy 1000 Storage system when the operating environment does not require user interaction (such as in a data center). Any activity that requires the use of a GUI must be done in Server with a GUI mode.
2 Installing and configuring the storage system Setup overview The HP StoreEasy 1000 Storage comes preinstalled with the Microsoft Windows Storage Server 2012 R2 Standard Edition operating system with Microsoft iSCSI Software Target included. Verify the kit contents Remove the contents, ensuring that you have all of the following components. If components are missing, contact HP technical support.
If you ordered the HP Tower to Rack Conversion Tray Universal Kit for the purpose of installing the 15x0 tower model in a rack, use the provided tower-to-rack conversion kit installation instructions to install the tower hardware into the rack.
Figure 19 HP D2700 Disk Enclosure I/O module ports 1. Port 1 2. Port 2 3. I/O module A 4. I/O module B Figure 20 D6000 I/O modules 1. Primary I/O module (Drawer 2) 2. Primary I/O module (Drawer 1) 3.
Cabling guidelines When connecting disk enclosures to the StoreEasy system, consider the following guidelines: In a single domain configuration, the secondary I/O modules on the D6000 are not used, so they may or may not be installed. The cabling diagrams in this section show the secondary I/O modules installed.
Figure 21 HP StoreEasy 14x0 with the P822 controller 1. D6000 enclosure 1 2. D6000 enclosure 2 3. Connection to SAS port 1 on the primary I/O module (Drawer 2) of D6000 enclosure 2 4. P822 controller 5. Connection to SAS port 1 on the primary I/O module (Drawer 2) of D6000 enclosure 1 6.
Figure 22 HP StoreEasy 14x0 with P421 and P222 controllers 1. D6000 Disk Enclosure 2. Connection between SAS port 1 on the primary I/O module (Drawer 2) and the P421 controller 3. P421 controller 4. P222 controller 5. Connection between SAS port 1 on the primary I/O module (Drawer 1) and the P421 controller 6.
Figure 23 HP StoreEasy 16x0 with the P822 controller 1. D6000 Disk Enclosure 1 2. D6000 Disk Enclosure 2 3. Connection between the P822 controller and SAS port 1 on the primary I/O module (Drawer 2) of D6000 Disk Enclosure 1 4.
Figure 24 HP StoreEasy 15x0 with the P222 controller 1. D2600 Disk Enclosure 1 2. D2600 Disk Enclosure 2 3. D2600 Disk Enclosure 3 4. D2600 Disk Enclosure 4 5. P222 controller 6. Connection from P222 controller to port 2 of I/O module A on disk enclosure 4 7.
Figure 25 HP StoreEasy 18x0 with the P822 controller 1. Group 1 of 4 D2600 Disk Enclosures 2. Group 2 of 4 D2600 Disk Enclosures 3. Connection from P822 controller to port 2 of I/O module A on the top disk enclosure in Group 1 4.
NOTE: The cabling diagram in Figure 26 (page 30) illustrates the HP StoreEasy 16x0 but the cabling is exactly the same for the HP StoreEasy 14x0 and 18x0 using the P822 controller. Cabling the storage system...
Figure 26 Alternate single domain configuration for better fault tolerance 1. Group 1 of 2 D2600 Disk Enclosures 2. Group 2 of 2 D2600 Disk Enclosures 3. Group 3 of 2 D2600 Disk Enclosures 4. Group 4 of 2 D2600 Disk Enclosures Installing and configuring the storage system...
Disk Enclosures. Figure 27 (page 31) shows the HP StoreEasy 14x0 system with the P822 controller in a dual domain configuration. In this configuration, the worst case scenario (besides a controller failure) is losing ½ of the D6000 if there is an I/O module failure.
I/O module in a disk enclosure if any I/O module fails. NOTE: The cabling diagram in Figure 28 (page 33) is exactly the same for the HP StoreEasy 14x0 and 18x0 using the P822 controller. Installing and configuring the storage system...
Figure 28 HP StoreEasy 16x0 with the P822 controller in a dual domain configuration (best fault tolerance) 1. Group 1 of 4 D2600 Disk Enclosures 2. Group 2 of 4 D2600 Disk Enclosures 3. Connection from the P822 controller to port 1 of I/O module B on the bottom D2600 in Group 1 4.
NOTE: The cabling diagram in Figure 29 (page 35) is exactly the same for the HP StoreEasy 14x0 and 16x0 using the P822 controller. Installing and configuring the storage system...
Figure 29 HP StoreEasy 18x0 with the P822 controller in a dual domain configuration (best performance) 1. Group 1 of 4 D2600 Disk Enclosures 2. Group 2 of 4 D2600 Disk Enclosures 3. Connection from the P822 controller to port 2 of I/O module B on the top D2600 in Group 1 4.
Using the default user information provided on the iLO Network Settings tag, log on to iLO, and then launch a remote console to the storage system. For detailed instructions on using iLO remote management software, see the HP iLO 4 User Guide.
The NCT (Network Configuration Tool) wizard enables you to configure the network interfaces on HP StoreEasy 1000 Storage. NCT analyzes all available network interfaces of the StoreEasy system and allows you to choose different network configurations to reduce the chances of any incorrect configuration.
HP StoreEasy Pool Manager is used to create one or more storage pools from the internal drives of the StoreEasy system. If any external storage enclosures are attached, Pool Manager is used to create storage pools there as well. The internal drives of StoreEasy models 14x0 and 15x0 are already pooled and contain the operating system, so no further pool management is necessary on these drives.
12 drive pool 1- 1 4 2 TB 5 or 6 / Balanced 10 / Performance 50 (2) or 60 (2) / Balanced 1 1 drive pool 1- 1 4 2 TB 5 or 6 / Balanced 10 drive pool 1- 1 4 2 TB 5 or 6 / Balanced...
5 drive pool 1- 1 2 6 TB 6 / Capacity 6 drive pool 1- 1 2 None 6 TB 6 / Capacity 10 / Performance 6 drive pool 1- 1 2 None 6 TB 6 / Capacity 10 / Performance 4 drive pool 1- 1 2 None...
6 drive pool 1- 1 2 None 2 TB 5 or 6 / Balanced 10 / Performance 4 drive pool 1- 1 2 None 2 TB 5 or 6 / Balanced 10 / Performance 7 drive pool 1- 1 2 2 TB 5 or 6 / Balanced 7 drive pool...
7 drive pool 1- 1 2 4 TB 6 / Capacity 7 drive pool 1- 1 2 4 TB 6 / Capacity 4 drive pool 1- 1 2 None 4 TB 5 or 6 / Balanced 10 / Performance 8 drive pool 1- 1 2 None 5 TB...
7 drive pool 1- 1 2 2 TB 5 or 6 / Balanced 7 drive pool 1- 1 2 2 TB 5 or 6 / Balanced 4 drive pool 1- 1 2 None 2 TB 5 or 6 / Balanced 10 / Performance 8 drive pool 1- 1 2...
10 / Performance 8 drive pool 1-25 2 TB 6 / Capacity 10 / Performance 6 drive pool 1-25 2 TB 5 or 6 / Balanced 10 / Performance 6 drive pool 1-25 2 TB 5 or 6 / Balanced 10 / Performance 6 drive pool 1-25...
8 drive pool 1-23 2 TB 5 or 6 / Balanced 10 / Performance 6 drive pool 1-23 None 2 TB 5 or 6 / Balanced 10 / Performance 6 drive pool 1-23 None 2 TB 5 or 6 / Balanced 10 / Performance 8 drive pool 1-23...
4 drive pool 1-23 2 TB 5 or 6 / Balanced 10 / Performance 4 drive pool 1-23 2 TB 5 or 6 / Balanced 10 / Performance 8 drive pool 1-23 2 TB 5 or 6 / Balanced 10 / Performance 8 drive pool 1-23 2 TB...
Adjusting logging for system, application, and security events. Installing third-party software applications—For example, these might include an antivirus application that you install. Registering the server — To register the server, see the HP registration website (http:// register.hp.com). Using Server Core The Server Core interface is a command prompt with PowerShell support.
PS C:\Users\Administrator>dism /online /enable-feature /featurename:OEM-Appliance-OOBE Then, install HP ICT from C:\hpnas\Components\ManagementTools. Configuring failover properties for multi-site environments You can configure failover properties for multi-site environments using DFS Management, which is available from the Tools menu in Windows Server Manager (Tools→DFS Management).
Windows Server Manager can be launched from the storage system desktop by clicking the icon on the left end of the task bar. The local HP StoreEasy Storage system as well as other Windows servers may be managed, as described in the...
Administrators can use the File and Storage Services role to setup and manage multiple file servers and their storage by using Server Manager or Windows PowerShell. Some of the specific applications include the following: Use Data Deduplication to reduce the disk space requirements of your files, saving money on storage.
UNIX, Linux, or Mac OS operating systems. NFS is supported on all HP StoreEasy 1000 Storage systems. All of the following types of NFS account mapping are supported: Active Directory® Domain Services (AD DS) mapped user access, Active Directory®...
4 Storage management overview This chapter provides an overview of some of the components that make up the storage structure of the storage system. Storage management elements Storage is divided into four major divisions: Physical storage elements Logical storage elements File system elements File sharing elements Each of these elements is composed of the previous level's elements.
Figure 30 Storage management process example Physical storage elements The lowest level of storage management occurs at the physical drive level. Minimally, choosing the best disk carving strategy includes the following policies: Analyze current corporate and departmental structure. Analyze the current file server structure and environment. Plan properly to ensure the best configuration and use of storage.
To protect against data loss from hard drive failure, storage systems should be configured with fault tolerance. HP recommends adhering to RAID 5 configurations. The table below summarizes the important features of the different kinds of RAID supported by the Smart Array controllers.
There are two types of LUN presentation: basic disk and dynamic disk. Each of these types of disk has special features that enable different types of management. The HP Pool Manager is used to create, edit, grow, shrink and delete storage pools.
Through the use of basic disks, you can create primary partitions or extended partitions. Partitions can only encompass one LUN. Through the use of dynamic disks, you can create volumes that span multiple LUNs. You can use the Windows Disk Management utility to convert disks to dynamic and back to basic and to manage the volumes residing on dynamic disks.
Management tools HP Systems Insight Manager HP SIM is a web-based application that allows system administrators to accomplish normal administrative tasks from any remote location, using a web browser. HP SIM provides device Network adapter teaming...
HP and third-party devices. IMPORTANT: You must install and use HP SIM to benefit from the Pre-Failure Warranty for processors, SAS and SCSI hard drives, and memory modules. For additional information, refer to the Management CD in the HP ProLiant Essentials Foundation Pack or the HP SIM website (http://www.hp.com/go/hpsim).
Click Start and then click ↓. Select HP System Tools→HP Array Configuration Utility. If the Execution Mode for ACU is set to Remote Mode, log on to the HP System Management Homepage. The default user name is Administrator and the password is the Windows Storage Server 2012 or 2012 R2 administrator password that is set by the storage system administrator.
This is a reserved volume and must be maintained as it exists. HP does not recommend spanning array controllers with dynamic volumes. The use of software RAID-based dynamic volumes is not recommended. Use the array controller instead; it is more efficient.
performance. Because defragmentation consolidates files and folders, it also consolidates the free space on a volume. This reduces the likelihood that new files will be fragmented. Defragmentation for a volume can be scheduled to occur automatically at convenient times. Defragmentation can also be done once, or on a recurring basis. NOTE: Scheduling defragmentation to run no later than a specific time prevents the defragmentation process from running later than that time.
For more information about RAID levels, see the Smart Array Controller User Guide, or the document titled Assessing RAID ADG vs. RAID 5 vs. RAID 1+0. Both are available at the Smart Array controller web page or at http://h18000.www1.hp.com/products/servers/proliantstorage/arraycontrollers/ documentation.html. Extend volumes using Disk Management The Disk Management snap-in provides management of hard disks, volumes or partitions.
The Volume Shadow Copy Service provides an infrastructure for creating point-in-time snapshots (shadow copies) of volumes. Shadow Copy supports 64 shadow copies per volume. A shadow copy contains previous versions of the files or folders contained on a volume at a specific point in time.
Although shadow copies are taken for an entire volume, users must use shared folders to access shadow copies. Administrators on the local server must also specify the \\servername\ sharename path to access shadow copies. If administrators or end users want to access a previous version of a file that does not reside in a shared folder, the administrator must first share the folder.
By keeping the shadow copy on the same volume, there is a potential gain in ease of setup and maintenance; however, there may be a reduction in performance and reliability. CAUTION: If shadow copies are stored on the same volume as the user files, note that a burst of disk input/output (I/O) can cause all shadow copies to be deleted.
Figure 34 System administrator view of Shadow Copies for Shared Folders The shadow copy cache file The default shadow copy settings allocate 10 percent of the source volume being copied (with a minimum of 350 MB), and store the shadow copies on the same volume as the original volume. (See Figure 35 (page 66)).
Figure 36 Shadow copies stored on a separate volume The main advantage to storing shadow copies on a separate volume is ease of management and performance. Shadow copies on a source volume must be continually monitored and can consume space designated for file sharing. Setting the limit too high takes up valuable storage space. Setting the limit too low can cause shadow copies to be purged too soon, or not created at all.
All shadow copies are listed, sorted by the date and time they were created. NOTE: It is also possible to create new shadow copies or delete shadow copies from this page. Set schedules Shadow copy schedules control how frequently shadow copies of a volume are made. There are a number of factors that can help determine the most effective shadow copy schedule for an organization.
Disabling shadow copies When shadow copies are disabled on a volume, all existing shadow copies on the volume are deleted as well as the schedule for making new shadow copies. CAUTION: When the Shadow Copies Service is disabled, all shadow copies on the selected volumes are deleted.
Shadow Copies for Shared Folders is required. The client-side application is available for Windows XP, Windows 2000 SP3+, and later operating system versions. No additional software is required to enable UNIX users to independently retrieve previous versions of files stored on NFS shares. NOTE: Shadow Copies for Shared Folders supports retrieval only of shadow copies of network shares.
Figure 38 Client GUI When users view a network folder hosted on the storage system for which shadow copies are enabled, old versions (prior to the snapshot) of a file or directory are available. Viewing the properties of the file or folder presents users with the folder or file history—a list of read-only, point-in-time copies of the file or folder contents that users can then open and explore like any other file or folder.
.@GMT-2003.04.27-04:00:00 .@GMT-2003.04.28-04:00:00 .@GMT-2003.04.29-04:00:00 Access to NFS shadow copy pseudo-subdirectories is governed by normal access-control mechanisms using the permissions stored in the file system. Users can access only those shadow copies to which they have read access at the time the shadow copy is taken. To prevent users from modifying shadow copies, all pseudo-subdirectories are marked read-only, regardless of the user's ownership or access rights, or the permissions set on the original files.
Click either Copy or Restore. Clicking Restore enables the user to recover everything in that folder as well as all subfolders. Clicking Restore does not delete any files. Backup and shadow copies Shadow copies are only available on the network via the client application, and only at a file or folder level as opposed to the entire volume.
Folder management Volumes and folders on any system are used to organize data. Regardless of system size, systematic structuring and naming conventions of volumes and folders eases the administrative burden. Moving from volumes to folders to shares increases the level of granularity of the types of data stored in the unit and the level of security access allowed.
Figure 39 Properties screen, Security tab Several options are available on the Security tab: To add users and groups to the permissions list, click Add. Follow the dialog box instructions. To remove users and groups from the permissions list, highlight the desired user or group, and then click Remove.
Figure 40 Advanced Security settings screen, Permissions tab Other functionality available in the Advanced Security Settings screen is illustrated in Figure 40 (page 76) and includes: Add a new user or group—Click Add, and then follow the dialog box instructions. Remove a user or group—...
Figure 41 User or group Permission Entry screen Another area of the Advanced Security Settings is the Auditing tab. Auditing allows you to set rules for the auditing of access, or attempted access, to files or folders. Users or groups can be added, deleted, viewed, or modified through the Advanced Security Settings Auditing tab.
Figure 42 Advanced Security Settings screen, Auditing tab Click Add to display the Auditing Entry screen. Figure 43 Auditing Entry for New Volume screen Click Select a principal to display the Select User or Group screen. File server management...
Figure 44 Select User or Group screen NOTE: Click Advanced to search for users or groups. Select the user or group. Click OK. Select the desired Successful and Failed audits for the user or group. 10. Click OK. NOTE: Auditing must be enabled to configure this information. Use the local Computer Policy Editor to configure the audit policy on the storage system.
If it is also necessary to take ownership of subfolders and files, enable the Replace owner on subcontainers and objects box. Click OK. Share management There are several ways to set up and manage shares. Methods include using Windows Explorer, a command line interface, or Server Manger.
This method results in a hierarchical security model where the network protocol permissions and the file permissions work together to provide appropriate security for shares on the device. NOTE: Share permissions and file-level permissions are implemented separately. It is possible for files on a file system to have different permissions from those applied to a share.
Quota management On the Quota Management node of the File Server Resource Manager snap-in, you can perform the following tasks: Create quotas to limit the space allowed for a volume or folder and generate notifications when the quota limits are approached or exceeded. Generate auto quotas that apply to all existing folders in a volume or folder, as well as to any new subfolders created in the future.
The ProLiant SNMP agents are enabled on the storage system by default and should not be disabled as they are used for internal management functions. If they are enabled for external client consumption, HP SIM must be configured so it does not attempt to communicate with these agents.
The HP System Management Homepage (SMH) is a web-based interface that consolidates and simplifies single system management for HP servers. The SMH is the primary tool for identifying and troubleshooting hardware issues in the storage system. You may choose this option to diagnose a suspected hardware problem.
By aggregating the data from HP web-based agents and management utilities, the SMH provides a common, easy-to-use interface for displaying the following information: Hardware fault and status monitoring System thresholds Diagnostics Software and firmware version control for an individual server The SMH Help menu provides documentation for using, maintaining, and troubleshooting the application.
The page provides system, subsystem, and status views of the server and displays groupings of systems and their status. NOTE: NICs will display with a failed status (red icon) if they are unplugged. To remove unused NICs from the system status, you can disable them by selecting Control Panel→Hardware→Device Manager, right-click on the specific NIC, and then select Disable.
The left panel provides links to information about the following items: Controller Select a storage controller to view its type, status, firmware version, and serial number. Physical Drives This section provides an overview of all disk drives attached to the controller. Drives are identified and grouped as assigned, unassigned, and spare drives.
To install the license key, see “Installing a license The SmartArray controller key with ACU” in the Configuring Arrays on HP Smart Array Controllers Reference that supports the Guide which can be downloaded from the following website: operating system drive is not licensed for RAID6.
An operation fails because it requires a service restart or cache update. The HP Storage Management Service has stopped running. To resolve the issue, restart the HP Storage Management Service using one of the following methods: From the desktop, navigate to the Services window (services.msc) and locate HP Storage Management Service.
Navigate to the C:\hpnas\components\PSP directory, which contains the WBEM installer. Open the batch script file and search for “HP Insight Management Agents for Windows Server x64 Editions” and identify its executable name. Then, run the executable to re-install the agents.
Right-click the HP StoreEasy Management website and select Manage Website. If it is running, the Start option will be disabled. If these steps do not resolve the issue, contact HP Technical Support. Error codes This section contains the error codes that may occur.
Windows PowerShell command Update-StorageProviderCache. 0x24005012 No physical disks were found in the logical drive. Please restart HP Storage Management Service. 0x25005013 Failed to update pool in cache. Please update the storage management provider cache by invoking Windows PowerShell command Update-StorageProviderCache.
Please update the storage management provider cache by invoking Windows PowerShell command Update-StorageProviderCache. 0x24005028 Failed to get proxy. Please restart HP Storage Management Service. 0x2500502A Failed to update the logical drive in cache. Please update the storage management provider cache by invoking Windows PowerShell command Update-StorageProviderCache.
Windows PowerShell command Update-StorageProviderCache. 0x2400503A The storage pool was not found in cache. Please restart HP Storage Management Service. 0x2500503A The storage pool was not found in cache. Please update the storage management provider cache by invoking Windows PowerShell command Update-StorageProviderCache.
Please update the storage management provider cache by invoking Windows PowerShell command Update-StorageProviderCache. 0x21005051 Failed to find the MI Main module. Please re-install HP Storage Management Provider. 0x21005052 Failed to initialize the MI Application. Please re-install HP Storage Management Provider. 0x21005053 The Storage Management Service is not able to Please re-install HP Storage Management Provider.
0x2100506D SMP assembly file not found. Please re-install HP Storage Management Provider. 0x2700506E The registry key The system is in an invalid state. Please contact HP Support. HKLM\HARDWARE\Description\System\BIOS was not found. 0x2700506F The registry key The system is in an invalid state. Please contact HP Support.
Table 5 Storage Management Provider errors (continued) Error code Error message Recommended action 0x2300507B This operation is supported only for spare drives. Please retry the operation. 0x2000507C The physical drive could not complete the operation because its health or operational status does not permit it.
Table 6 Pool Manager Provider errors (continued) Error code Error message 0x20006015 Some of the disks within the proposed pool are already part of another pool, which spans the current virtual enclosure. 0x20006016 Some of the disks within the proposed pool are unhealthy. 0x20006017 Some of the disks within the proposed pool are offline.
HP ProLiant Servers Troubleshooting Guide IMPORTANT: Some troubleshooting procedures found in ProLiant server guides may not apply to the storage system. If necessary, check with your HP Support representative for further assistance. For HP StoreEasy 1000 Storage guides, go to http://www.hp.com/support/...
Microsoft Systems Center Operations Manager (SCOM) provides comprehensive monitoring, performance management, and analysis tools to maintain Windows OS and application platforms. This solution allows you to monitor Microsoft Windows environments and HP storage products through a common OpsMgr console. To download HP management packs for Microsoft System...
During system recovery, you can replace the existing drives with drives of the same size or larger. HP recommends that the replacement drives be the same type as the original drives, but it is not required. However, drives in the same RAID group must all be the same type (you cannot mix drive types in a RAID group).
Reboot the server blade to either the USB flash device or USB DVD drive. The system BIOS attempts to boot to the USB device first by default. Watch the monitor output during the boot as you may need to press a key to boot to the USB media. NOTE: If directly connected, you may have to change the BIOS settings to ensure proper boot sequence.
Restoring the system with Windows Recovery Environment NOTE: To use Windows Recovery Environment, you must have created a system backup with the Windows Server Backup utility. Do one of the following: For direct access, connect the cable and insert the System Recovery DVD in the client PC. For remote management access, connect to the server using iLO from a client PC.
13. Enter the login credentials for authentication and click OK. 14. Select the date and time of the system image that you want to restore and click Next. 15. Select Format and repartition disks to delete existing partitions and reformat all disks during the restore process and click Next.
Operating system type and revision level Detailed questions Subscription service HP recommends that you register your product at the Subscriber's Choice for Business website: http://www.hp.com/go/e-updates After registering, you receive email notification of product enhancements, new driver versions, firmware updates, and other product resources.
HP customer self repair (CSR) programs allow you to repair your storage product. If a CSR part needs replacing, HP ships the part directly to you so that you can install it at your convenience. Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a repair can be accomplished by CSR.
9 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (firstname.lastname@example.org). Include the document title and part number, version number, or the URL...
Logical Disk 1 Operating System Volume (450 GB) RAID 1 Physical Drives 1–2 NOTE: In the HP Array Configuration Utility (ACU), mapping of logical disks begins at 1. In Microsoft Disk Manager, mapping begins at 0. 108 Operating system logical drives...
If the operating system has a failure that might result from corrupt system files, a corrupt registry, or the system hangs during boot, see “Storage system recovery” (page 101).
Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, California 94304, U.S. Local Representative information Russian: HP Russia: ЗАО “Хьюлетт-Паккард А.О.”, 125171, Россия, г. Москва, Ленинградское шоссе, 16А, стр.3, тел/факс: +7 (495) 797 35 00, +7 (495) 287 89 05 HP Belarus: ИООО «Хьюлетт-Паккард Бел», 220030, Беларусь, г. Минск, ул.
HP Enterprise Servers http://www.hp.com/support/EnterpriseServers-Warranties HP Storage Products http://www.hp.com/support/Storage-Warranties HP Networking Products http://www.hp.com/support/Networking-Warranties Warranty information 1 1 1...
(such as a server that hosts Exchange or SQL Server) and a target device (such as the HP All-in-One Storage System). By carrying SCSI commands over IP networks, iSCSI is used to facilitate data transfers over intranets and to manage storage over long distances.
Logical unit number. A LUN results from mapping a logical unit number, port ID, and LDEV ID to a RAID group. The size of the LUN is determined by the emulation mode of the LDEV and the number of LDEVs associated with the LUN. mount point A host's file system path or directory name where a host volume (device) is accessed.
55, Belarus Kazakhstan Russia EAC marking, 1 10 hardware components HP StoreEasy 1430 Storage, cache file, shadow copies, HP StoreEasy 1530 Storage, Certificate of Authenticity (COA), HP StoreEasy 1630 Storage, configuration...
LUNs in volumes, Subscriber's Choice for Business, summary of methods, Support websites recovering the system, contacting HP, system recovery DVD, HP, 99, USB flash drive, Subscribers's Choice for Business, regulatory information, 1 10 Subscription service,...
HP Enterprise servers, 1 10 HP Networking products, 1 10 HP ProLiant and X86 Servers and Options, 1 10 HP Storage products, 1 10 websites customer self repair, 1 16 Index...