Navigating The Lcd; Setup Window - Lectrosonics SRa5P Instruction Manual

SRa5P and SRa Dual Receivers

Navigating the LCD

Receiver 1
Pilot Tone
ON\OFF
Receiver 2
Pilot Tone
ON/OFF

Setup Window

SETUP
BACK
(item)
MENU
Press
2
UP/DOWN
657.500
to select
SETUP
LEVEL
SEL
LEVEL
BACK
BACK
UP
DOWN
SETUP
SEL
SCAN
BACK
BACK
UP DOWN
SETUP
DIVMOD
SEL
DIVMODE BACK
DOWN
UP
RECEIVER 1
SETUP COMPAT
SEL
COMPAT BACK
DOWN
UP
RECEIVER 1
TUNING
SEL
TUNING
BACK
DOWN
UP
RECEIVER 1
SETUP SmtNR
SEL
SmtNR BACK
DOWN
UP
RECEIVER 1
SETUP PHASE
SEL
PHASE BACK
DOWN
UP
RECEIVER 1
SETUP TXBAT
SEL
TXBAT BACK
DOWN
UP
SETUP MIXTRIM
SEL
MIXTRIM
BACK +05
DOWN
UP
SETUP MIXMODE
SEL
MIXMODE
BACK
DOWN
UP
RECEIVER 1
SETUP TONE?
SEL
TONE
BACK
+05
DOWN
BACK
16
Main Window
Hold MENU and
press UP
momentarily
Hold MENU and
press DOWN
momentarily
BACK
MENU
Receiver 1
1 80
BACK
652.800
MENU
Press UP/DOWN to change frequency
Receiver 2
AF
Press UP/DOWN to change frequency
RECEIVER 1
RECEIVER 2
LEVEL
SEL
00 00 SEL 00
00
SCANNING SCANNING
STARTS STOPS
5E
SEL
Press
NOTE: Main Window will look like this
UP/DOWN
when the RATIO DIV mode is selected.
RATIO
to select
RECEIVER 2
Press
COMPAT
SEL to
HYB HYB HYB
select
receiver
RECEIVER 2
Press
TUNING
SEL to
a
select
NOR
NOR
receiver
RECEIVER 2
Press
SmtNR
SEL to
select
NOR FUL
NOR
receiver
RECEIVER 2
Press
PHASE
SEL to
+ +
select
receiver
RECEIVER 2
Press
TXBAT
SEL to
9V select
9V 9V
receiver
Press
MIXTRIM
SEL to
00
00 select
receiver
Press
UP/DOWN
MIXBOTH
to select
RECEIVER 2
Press
TONE?
SEL to
+05
select
00
receiver
Hold MENU
and hold UP
Hold MENU and
hold DOWN
RATIO 80
652.800
Receiver 2 should always be set to a higher frequency
than Receiver 1 by at least 400 kHz (four standard steps).
WARNING
Press
UP/DOWN
to adjust
Press
B3
4A
SEL to
2
1 select
receiver
Press
UP/DOWN
HYB
to select
Press
UP/DOWN
a
to select
Press
UP/DOWN
FUL
to select
Press
UP/DOWN
to select
Press
UP/DOWN
9V
to select
Press
UP/DOWN
+05
to select
RECEIVER 1
Press
LVL 1K
UP/DOWN
00 +05
to select
NOTE: Press the
Mute Audio on
BACK button from
Receiver 1
the Main Window
to briefly display
Mute Audio on
the external power
Receiver 2
supply voltage.
When the receivers are combined in the
RATIO DIVERSITY mode, the frequency
screen will look like this.
IMPORTANT:
Performance will be degraded if
FREQ.
Receiver 1 is set 4.2 to 4.8 MHz higher
than Receiver 2. The LCD will also flash
this message periodically.
ZOOM GRAPHIC
Press UP/DOWN
Press both
to scroll
UP and DOWN
frequency
to ZOOM
BACK
NOTE: To reset the timer, set the TXBAT
mode to anything other than 9VT or AAT,
then back to the desired mode.
NOTE: This setting does not
appear when the MIXMODE
is set to DIRECT
Tone will be enabled
when level is set with
00
the UP/DOWN buttons
LECTROSONICS, INC.
B3
Press UP/DOWN
to scroll
frequency