Navigating The Lcd - Lectrosonics SRc-941 Instruction Manual

SRc-941 Dual Receiver

Navigating the LCD

Setup Screen
SETUP
(item)
Press
UP/DOWN
to select
SETUP
LEVEL
UP
SETUP
DEFAULT
DOWN
UP
SETUP
SMARTUNE
DOWN
UP
SETUP
IR SYNC
DOWN
UP
SETUP
SCAN
UP DOWN
SETUP
DIVMODE
DOWN
UP
SETUP
TALKBACK
DOWN
UP
SETUP
COMPAT
DOWN
UP
SETUP
TUNING
DOWN
SETUP
STEPSIZE
DOWN
UP
SETUP
SmtNR
DOWN
UP
SETUP
PHASE
DOWN
UP
SETUP
TXBAT
DOWN
UP
DOWN
UP
SETUP
MIXMODE
DOWN
UP
SETUP
TONE
DOWN
16
Main Window
Receiver 1
Hold MENU and
Pilot Tone
press UP
ON\OFF
momentarily
Receiver 2
Hold MENU and
Pilot Tone
press DOWN
ON/OFF
momentarily
BACK
Switched
: Receiver 1
1 01
941
BACK BACK
941.600
MENU MENU Press UP/DOWN to
change frequency
Receiver 2
:
2 7A
941
953.700
Press UP/DOWN to change frequency
RECEIVER 1
RECEIVER 2
LEVEL LEVEL
SEL SEL
BACK 00 00 00
SEL
BACK
Press
DEFAULT
SEL
DOWN to
RESET– –
BACK
continue
1 1
TX
SMART
SEL
TUNE BAND B1
BACK
1
SYNC Press UP to sync TX 1
SEL
2
Press DOWN to sync TX 2
BACK
SCANNING SCANNING
BEGINS STOPS
941
SEL
SEL
BACK 8A
BACK
NOTE: The Main Window will
Press
DIVMOD
SEL
UP/DOWN
look like this when the RATIO
RATIO
BACK
to select
DIV mode is selected.
TALKBACK Press
SEL
UP/DOWN
OFF
BACK
to select
RECEIVER 1
Press
COMPAT 1
UP/DOWN MENU/SEL
SEL
to select to highlight
BACK NU HYBR
receiver
RECEIVER 1 RECEIVER 2
Press
TUNING TUNING
SEL
SEL to
u
BACK select
NOR NOR
receiver
Press
STEPSIZE
SEL MENU/SEL
100 25 to highlight
BACK
receiver
RECEIVER 1
RECEIVER 2
Press
SmtNR SmtNR
SEL
SEL to
FUL
BACK NOR select OFF
receiver
RECEIVER 1 RECEIVER 2
Press
PHASE
PHASE
SEL
SEL to
+ +
BACK select
receiver
RECEIVER 1
Press
TXBAT
TXBAT
SEL
SEL to
BACK 9V AA select 9V
receiver
Press
SEL to
00 00
BACK select 00
receiver
MIXMODE Press
SEL
UP/DOWN
MIXBOTH
BACK
to select
Press
RECEIVER 1 SEL to RECEIVER 2
select
TONE?
TONE?
receiver
SEL
+05
BACK +05 00
BACK
Mute Audio on
Hold MENU
Receiver 1
and hold UP
for 1 sec. or
more
Hold MENU and Mute Audio on
Receiver 2
hold DOWN for
1 sec. or more
MENU
Ratio
When DIVMODE is set to RATIO the
frequency screen will look like this.
Ratio
Block
Mode
: 01
R
941
941.600
Press
UP/DOWN
00
to adjust
Press
ARE YOU
MENU/SEL
SURE?
to reset
Press Press
OK
UP/DOWN MENU/SEL
to select to start SYNC
scanning
band
NOTE: An error message will appear if a setting on the
transmitter cannot be enabled by the SYNC procedure.
Press
Press
941 941
UP/DOWN
SEL to
to scroll
select
8A 8A
frequency
receiver
BACK
RECEIVER 2
Press
Press
COMPAT 2
UP/DOWN
to select
IFB SER
mode
mode
Press
UP/DOWN
v
to select
mode
Press
STEPSIZE
UP/DOWN
to select
100 25
step size
Press NOTE: N/A will appear if the COMPAT mode is
UP/DOWN
set to IFB SER since there is no noise reduction
to select
N/A
available in the IFB mode.
mode
Press
UP/DOWN
to select
Press
NOTE: To reset the timer, set the TXBAT mode to anything
UP/DOWN
AA
other than 9VT or AAT, then back to the desired mode.
to select
Press
NOTE: This setting does not appear
UP/DOWN
to select
+05
when the MIXMODE is set to DIRECT.
value
RECEIVER 1
Press
LVL 1K
UP/DOWN
00
+05 00
to select
NOTE: Press the BACK
button from the Main
Window to briefly display
the external power
supply voltage, and
the transmitter battery
voltages.
Freq hex code
Freq MHz
Follow
NOTE: Fewer screens are
Press
prompts to
MENU/SEL
shown when DIVMODE is
scan and set
to continue
up TX 2
set to RATIO.
Press
1
DOWN to IR
sync TX 1
Press both
25
UP and
DOWN to
ZOOM
Press
UP/DOWN to
scroll
frequency
Tone will be enabled
when level is set with
the UP/DOWN buttons
LECTROSONICS, INC.