Table of Contents
Advertisement
LDVR Series Direct Vent Gas Fireplace
Locating Your Fireplace
E
Y
D
Y
F
Fig. 2 Locate gas fireplace.
A) Flat on wall
B) Cross corner
D) *Room divider
E) *Flat on wall corner
Y) 6" minimum
NOTE: (Fig. )
** Island (C) and Room Divider (D) installation is possible as long
as the horizontal portion of the vent system (X) does not exceed
0' (610cm). See details in Venting Section.
* When you install your fireplace in(D) Room divider or (E) Flat
on wall corner positions (Y), a minimum of 6" (153mm) clearance
must be maintained from the perpendicular wall and the front side
edge of the fireplace. Refer to (Y) in Figure .
Clearance to Combustibles
Top of Unit to Ceiling ............................... 36" (914 mm)
Appliance
Top .......................................................... 0" (0 mm)
Bottom ..................................................... 0" (0 mm)
Side ......................................................... 0" (0 mm)
Back ........................................................ 0" (0 mm)
Venting
Concentric sections of DV Vent
Top, bottom & sides .............................. 1" (5 mm)
Rear Vent Applications:
Top ........................................................ " (50 mm)
Sides and Bottom .................................. 1" (5 mm)
Flex Vent ............................................ 7/8" ( mm)
Mantels
The height that a combustible mantel is fitted above the
fireplace is dependent on the depth of the mantel. This also
applies to the distance between the mantel leg (if fitted)
and the fireplace.
For the correct mounting height and widths refer to Figs.
3a and 3b, and the following Mantel Charts.
The fitting of a bay window trim kit does not effect the
distances and reference points referred to in the diagram
and chart.
Noncombustible mantels and legs may be installed at any
height and width around the appliance.
When using paint or lacquer to finish the mantel, such paint or
lacquer must be heat resistant to prevent discoloration.
6
A
B
X
C
X
B
LU584-R
LU584-R
Locating unit
2/23/01 sta
C) **Island
F) Chase installation
A
B
C
CFM146
Mantel Chart
Mantel Shelf
Ref. or Breast Plate Ref.
Depth
V
10"
(54 mm)
A
W
8"
(03 mm)
B
X
6"
(15 mm)
C
Y
4"
(10 mm)
D
Z
"
(51 mm)
E
Fig. 3a Combustible mantel minimum installation.
Black
Surround
Face
CFM164a
Side of
Combustion Chamber
CFM164a
Mantel Leg Chart
06/22/01 sta
Mantel
Ref.
Leg Depth
F
10" (54 mm)
CFM170
DV Builder Front
G
8" (03 mm)
View
H
6" (15 mm)
I
4" (10 mm)
J
" (51 mm)
Fig. 3b Combustible mantel leg minimum installation.
V
W
X
Y
Z
3/4" (19 mm) Scribe
Moulding for use with
Vermont Castings
Group Cabinets
D
E
Fireplace
Top Louvre
Assembly
Top of Combustion
Chamber
CFM146
Mantel from Top
DV Mantel Chart
7/5/01 sta
of Combustion Chamber
36/39/43 LDVR
33LDVR
17" (43 mm) 16¹⁄₂" (419 mm)
15" (381 mm) 14¹⁄₂" (368 mm)
13" (330 mm) 1¹⁄₂" (318 mm)
11" (79 mm) 10¹⁄₂" (67 mm)
9" (9 mm) 8¹⁄₂" (16 mm)
3/4" (19 mm) Scribe
Moulding for use with
Vermont Castings Group
Cabinets
J
I
H
G
Mantel
Leg
K
L
M
N
O
Mantel Leg FromSide
Ref.
of Comb. Opening
K
11¹⁄₂"
(9 mm)
L
9¹⁄₂"
(41 mm)
M
7¹⁄₂"
(191 mm)
N
5¹⁄₂"
(140 mm)
O
3¹⁄₂"
(89 mm)
10007317
F
CFM170
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
