Related Manuals for Longshine GFT-150 Series
Summary of Contents for Longshine GFT-150 Series
- Page 1 Flexible / Classy / High Performance POS GFT-150 Series USER’S MANUAL All-in-One Touch Screen POS System Intel Pentium Mobile Motherboard, 15 inches LCD Monitor Available in BLACK & SILVER colors...
-
Page 2: About This Manual
Preface About this Manual Thank you for purchasing POS GFT-150 Series All-in-One system. This terminal offers all the enhanced features and is easy to connect to various optional devices for optimal performance. This user manual describes how you setup and connect your terminal. -
Page 3: Declaration Of Conformity
Preface Federal Communications Commission (FCC) Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesirable operation. -
Page 4: Important Safety Information
Important Safety Information BEFORE YOU PROCEED Read the safety notices and the User’s Manual carefully before using the product. Keep the box and packaging in case the product needs to be shipped in the future. Follow the product and warning label instructions. For safety reasons, only qualified service personnel should open the terminal. - Page 5 Important Safety Information ! OPERATING INSTRUCTIONS Keep the User’s Manual for future reference. Follow the product label instructions. Lay this terminal on a stable surface when installing. Heavy objects placed on the product can cause damage or obstruct proper ventilation. If one of the following situations arises, notify a qualified service technician immediately: The power cord or plug is damaged.
-
Page 6: Table Of Contents
CONTENTS 1. Introduction............................1 Welcome............................1 1.1 How to Use This Manual ....................1 1.2 A Visual Tour of POS GFT-150 Series Terminal ............2 1.2a What Comes With POS GFT-150 Series Terminal ..........4 1.2b Dimension 15” .....................6 1.2c Adjustable LCD Operation Angle ................7 1.3 Features ..........................7... -
Page 7: Introduction
1.1 How to Use This Manual This manual contains all the information needed for setting up a POS GFT-150 Series Terminal. In addition, you can also consult the manual for the operation system and added peripheral hardware. Provides an introduction to POS GFT-150 Series Terminal and this user’s manual. -
Page 8: A Visual Tour Of Pos Gft-150 Series Terminal
Introduction 1.2 A Visual Tour of POS GFT-150 Series Terminal Before you start, take a few moments to become familiar with POS GFT-150 Series Terminal. Elegant, Solid, Fashionable Compact Design Easy to reach I/O Connector Ports (Back Side of Machine) - Page 9 Introduction Available in 15” TFT LCD Touch 3 in 1 MSR Monitor Smartcard i-Button Reader WIFI Air Vent (on both left and right sides) Finger print-Free Front Bezel Design Auto Power Switch, Speak Hole Bright Control Cover...
-
Page 10: What Comes With Pos Gft-150 Series Terminal
1.2a What Comes With POS GFT-150 Series Terminal The following items are standard with POS GFT-150 Series terminal. Before setting up your POS GFT-150 Series terminal, check that the package contains the following items. If any of the items are missing or damaged, contact your supplier immediately. - Page 11 Introduction Optional Items: 3 in 1 MSR + Smartcard + i-Button Reader VFD Customer Display Second LCD monitor 8” 10” Peripherals (Scanner, Cash drawer, Receipt printer) POS GT-Series with 3 in 1 MSR + POS GT-Series with Second Monitor Smartcard + i-Button Reader VFD Customer Display Peripherals Receipt Printer...
-
Page 12: Dimension 15
Introduction 1.2b Dimension 15” 15” POS GFT-series Terminal 15” POS GFT-series Terminal Dimensions: and MSR Dimensions: 15” POS GFT-series Terminal 15” POS GFT-series Terminal and VFD customer display: and second LCD monitor:... -
Page 13: Adjustable Lcd Operation Angle
1.2c Adjustable LCD Operation Angle “ Super Firm and Perfectly Secured LCD display Angles from 0 ~ 70 degree” 1.3 Features POS GFT-150 Series terminal comes equipped with the following features: Low power consumption LV (Low Voltage) design of the device is embedded with a unique chip set and CPU renders power saving function. -
Page 14: Connector Panels
Introduction 1.4 Connector Panels The connector panel is located at the bottom of the main unit base. To clearly see the panel you must open the base cover. Chart of the connector panel: I/O Port Connector Type Description PS/2 PS/2 Mouse Use this port for an external mouse. -
Page 15: Switch Panels
Introduction 1.5 Switch Panels The switch panel is located in the front of the device. To clearly see the panel you must open the cover. Button Description Reset Press this button to reboot the device. Brightness Press + to increase or – to Adjustment decrease the brightness. -
Page 16: Hardware Setup
Introduction 2. Hardware Setup Getting Started This section describes how to install the optional accessories on your POS GFT-series Touch Terminal for optimal serviceability. 2.1 Pre-installation Notice Before you start installing POS GFT-series terminal, please read the following notices carefully. 1. -
Page 17: Hardware Assembly
Hardware Setup Hardware Assembly Please make sure that the system power is turned off and the power supply is disconnected when making any hardware changes to POS GFT-series terminal. 2.2a COM power selection Change the Jumper position Before you start using the COM port, please make sure that JP2 (for COM 4), JP3 (for COM 6), JP5 (for COM 5) and JP6 (for COM 3) on the main board are set correctly. -
Page 18: Compact Flash Installation
Hardware Setup 2.2b Compact Flash Installation…… Package Content A Compact Flash (CF) card Installing a CF Card 1. Turn off the system power. 2. Turn over the GFT series, the CF Card socket is found under the case. 3. Unscrew the metal piece and take it off. 4. -
Page 19: Magnetic Stripe Reader Installation
Hardware Setup 2.2c Magnetic Stripe Reader Installation…… An optional Magnetic Stripe Reader (MSR) can be installed on the right side of GFT-150 Terminal. Package Content An MSR A cable clip Screw x 2 Installing an MSR Turn off the system power. Using two screws to secure the MSR to the right side of the monitor. - Page 20 Hardware Setup Loosen the two screws on both sides as the picture shown below. Slide out the rear plate (A) and take off the back plate (B). Loosen the screw (C) and slide the unit outwards to reach the main board. Loosen this screw!
- Page 21 Hardware Setup On the main board, take off all the jumpers on JP29 port. Trace the MSR cable into the unit using the cable clip on the side to secure the cable. Connect the MSR cable to the JP29 port.
- Page 22 Hardware Setup Replace the case, back and rear plate. Screw You may turn the system back on once the MSR is completely installed.
-
Page 23: D 3-In-1 Card Reader Installation
Hardware Setup 2.2d 3-in-1 Card Reader Installation… An optional 3-in-1 Card Reader can be installed on the right side of GFT-150 Terminal. Package Content A 3-in-1 Card Reader A metal piece for securing 3-in-1 Card Reader A cable clip Screw x 4 Installing a 3-in-1 Card Reader Note: Before installing a 3-in-1 Card Reader, please make sure the jumper is set correctly on the... - Page 24 Hardware Setup 5. Loosen the two screws on both sides as the picture shown below. 6. Slide out the rear plate (A) and take off the back plate (B). Loosen the screw (C) and slide the unit outwards to reach the main board. Loosen this screw!
- Page 25 Hardware Setup 7. Trace the 3-in-1 Card Reader cable into the unit using the cable clip on the side to secure the cable. Connect the 3-in-1 Card Reader cable to the COM port. 8. Replace the case, back and rear plate. Screw 9.
-
Page 26: Vfd Customer Display Installation
Hardware Setup 2.2e VFD Customer Display Installation… Package Content A VFD VFD Pole x 2 A cable clip A circular base A COM cable Screw x 2 Assemble and Disassemble the Circular pole There are two standard pole heights that may be ordered. You can regulate the height of VFD for your preference. - Page 27 Hardware Setup Installing a VFD Note: Before installing a VFD, please make sure the jumper is set correctly on the main board (Please refer to 2.2a COM power selection). The supply voltage for the customer display should be set to +12V. 1.
- Page 28 Hardware Setup 4. On VFD monitor, there are two cables. Please use the longer one to connect with the COM cable. 5. Position the VFD display into the holder. 6. Connect the VFD COM cable to the COM port. 7. Turn on VFD power switch, and then turn on system power.
-
Page 29: Wifi Installation
Hardware Setup 2.2f WiFi Installation…… An optional WiFi can be installed on the right side of GFT-150 Terminal. Package Content A Mini-PCI card A detachable antenna An Antenna line An U-shape base A cable clip Screw x 2 Installing WiFi 1. - Page 30 Hardware Setup 4. Screw the U-shape base to the unit, and then penetrate the antenna inside. Penetrate the Antenna line into this hole!! 5. Trace the Antenna line into the unit using the cable clip on top of the LPT port to secure the cable.
- Page 31 Hardware Setup 6. Replace the case, back and rear plate. Screw 7. Broken the hole on the back panel and attach the antenna on. 8. You may turn the system back on once the WiFi is completely installed.
-
Page 32: Rfid Installation
Hardware Setup 2.2g RFID Installation…… An optional RFID Card can be installed on the GFT-150 Terminal. Package Content A RFID card A RFID cable Screw x 2 Installing RFID 1. Turn off the system power. 2. Loosen the two screws on both sides as the picture shown below. 3. - Page 33 Hardware Setup Remove the RAM card! Important Note: Please face the antenna outward. The antenna is RFID cable on the side with chips. Face the chip-side to the front. Or it may cause poor performance.
- Page 34 Hardware Setup 6. Replace the case, back and rear plate. Screw 7. You may turn the system back on once the RFID card is completely installed.
-
Page 35: Wall Mount Installation
Hardware Setup 2.2h Wall Mount Installation… GFT-150 Terminal can be wall-mounted on a flat surface. Package Content A mounting plate Screw x 4 Wall mount Installation 1. Turn off the system power. 2. Select a location with access for cables and a power outlet. 3. -
Page 36: Lcd And Touch Panel Replacement
Hardware Setup 2.3 LCD and Touch Panel Replacement 1. Loosen the screw on the back of the monitor and open the cover. 2. Slide the unit outwards. 3. Unplug all the cables on the rear of the monitor. LVDS connector Touch control board to (for LCD panel) Power connector... - Page 37 Hardware Setup 4. Loosen the two screws from the bracket and the other two screws on the bottom of the device. 5. Loosen the six screws to depart the front cover from the monitor.
- Page 38 Hardware Setup 6. Loosen the four screws (marked in red) to depart the back cover from the monitor. Then, loosen the other four screws (marked in blue) to depart the touch panel from the bracket. Note: Please reverse the steps from step 6 to step 1 to replace the LCD and touch panel. Pay attention to the position of each cable during re-plug (step 3).
-
Page 39: Specification
Specification 3. Specification Technical Information System Model Name GFT-150 Motherboard VIA C7-M 1.5GHz, 400 MHz FSB System Frequency 400 MHz Memory One DDR2 DIMM 240-PIN socket up to 1GB (Support DDR2 533/400 unregistered non-ECC) 10/100Mbps Ethernet Ethernet Graphic AGP 8X hardware 2D/3D Video Graphic Accelerators Onboard (Support 2 VGA Output) Display... -
Page 40: Motherboard Configuration
Specification Others Optional Integrated Second 8"/10" LCD Screen without Touch Monitor Device VFD Customer Display MSR Card Reader 3 in 1 (MSR + Smart Card + iButton Reader) WiFi RFID Sound Speaker There is LVDS chip onboard M6 M/B which is responsible for connecting the primary LCD display. However the motherboard it self has one VGA port which then can be responsible for connecting the second LCD display. - Page 41 Specification...