Related Manuals for Longshine POS GT-150 Series
Summary of Contents for Longshine POS GT-150 Series
- Page 1 Flexible / Classy / High Performance POS GT-150 Series USER’S MANUAL All-in-One Touch Screen POS System Intel Pentium Mobile Motherboard, 15 inches LCD Monitor Available in BLACK & SILVER colors...
- Page 2 Preface About this Manual Thank you for purchasing POS GT-150 Series All-in-One system. This terminal offers all the enhanced features and is easy to connect to various optional devices for optimal performance. This user manual describes how you setup and connect your terminal.
- Page 3 Preface Federal Communications Commission (FCC) Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesirable operation.
- Page 4 Important Safety Information BEFORE YOU PROCEED Read the safety notices and the User’s Manual carefully before using the product. Keep the box and packaging in case the product needs to be shipped in the future. Follow the product and warning label instructions. For safety reasons, only qualified service personnel should open the terminal.
- Page 5 Important Safety Information ! OPERATING INSTRUCTIONS Keep the User’s Manual for future reference. Follow the product label instructions. Lay this terminal on a stable surface when installing. Heavy objects placed on the product can cause damage or obstruct proper ventilation. If one of the following situations arises, notify a qualified service technician immediately: The power cord or plug is damaged.
-
Page 6: Table Of Contents
CONTENTS 1. Introduction............................1 Welcome............................1 1.1 How to Use This Manual ....................1 1.2 A Visual Tour of POS GT-150 Series Terminal..............2 1.2a What Comes With POS GT-150 Series Terminal..........4 1.2b Dimension 15” .....................6 1.2c Adjustable LCD Operation Angle ................7 1.3 Features ..........................7 1.4 Connector Panels......................8... -
Page 7: Introduction
1.1 How to Use This Manual This manual contains all the information needed for setting up a POS GT-150 Series Terminal. In addition, you can also consult the manual for the operation system and added peripheral hardware. Provides an introduction to POS GT-150 Series Terminal and this user’s manual. -
Page 8: A Visual Tour Of Pos Gt-150 Series Terminal
Introduction 1.2 A Visual Tour of POS GT-150 Series Terminal Before you start, take a few moments to become familiar with POS GT-150 Series Terminal. Elegant, Solid, Fashionable Compact Design Easy to reach I/O Connector Ports (Back Side of Machine) - Page 9 Introduction Available in 15” TFT LCD Touch 3 in 1 MSR Monitor Smartcard i-Button Reader WIFI Air Vent (on both left and right sides) Finger print-Free Front Bezel Design Auto Power Switch, Speak Hole Bright Control Cover...
-
Page 10: What Comes With Pos Gt-150 Series Terminal
1.2a What Comes With POS GT-150 Series Terminal The following items are standard with POS GT-150 Series terminal. Before setting up your POS GT-150 Series terminal, check that the package contains the following items. If any of the items are missing or damaged, contact your supplier immediately. - Page 11 Introduction Optional Items: 3 in 1 MSR + Smartcard + i-Button Reader VFD Customer Display Second LCD monitor 8” 10” Peripherals (Scanner, Cash drawer, Receipt printer) POS GT-Series with 3 in 1 MSR + POS GT-Series with Second Monitor Smartcard + i-Button Reader VFD Customer Display Peripherals Receipt Printer...
-
Page 12: Dimension 15
Introduction 1.2b Dimension 15” 15” POS GT-series Terminal 15” POS GT-series Terminal Dimensions: and MSR Dimensions: 15” POS GT-series Terminal 15” POS GT-series Terminal and VFD customer display: and second LCD monitor:... -
Page 13: Adjustable Lcd Operation Angle
1.2c Adjustable LCD Operation Angle “ Super Firm and Perfectly Secured LCD display Angles from 0 ~ 70 degree” 1.3 Features POS GT-150 Series terminal comes equipped with the following features: Low power consumption LV (Low Voltage) design of the device is embedded with a unique chip set and CPU renders power saving function. -
Page 14: Connector Panels
Introduction 1.4 Connector Panels The connector panel is located at the bottom of the main unit base. To clearly see the panel you must open the base cover. Chart of the connector panel: I/O Port Connector Type Description PS/2 PS/2 Mouse Use this port for an external mouse. -
Page 15: Switch Panels
Introduction 1.5 Switch Panels The switch panel is located in the front of the device. To clearly see the panel you must open the cover. Button Description Reset Press this button to reboot the device. The USB (Universal Serial Bus) port can be used to connect USB devices. -
Page 16: Hardware Setup
Hardware Setup 2. Hardware Setup Getting Started This section describes how to install the optional accessories on your POS GT-series Touch Terminal for optimal serviceability. 2.1 Pre-installation Notice Before you start installing POS GT-series terminal, please read the following notices carefully. 1. -
Page 17: Hardware Assembly
Hardware Setup Hardware Assembly Please make sure that the system power is turned off and the power supply is disconnected when making any hardware changes to POS GT-series terminal. 2.2a COM power selection Change the Jumper position Before you start using the COM port, please make sure that JP1 (for COM 3), JP2 (for COM 2), JP4 (for COM4 ) and JP5 (for COM 1) on the main board are set correctly. -
Page 18: Compact Flash Installation
Hardware Setup 2.2b Compact Flash Installation…… Package Content A Compact Flash (CF) card Installing a CF Card 1. Turn off the system power. 2. Turn over the GT series, the CF Card socket is found under the case. 3. Unscrew the metal piece and take it off. 4. -
Page 19: Magnetic Stripe Reader Installation
Hardware Setup 2.2c Magnetic Stripe Reader Installation…… An optional Magnetic Stripe Reader (MSR) can be installed on the right side of GT-150 Terminal. Package Content An MSR A cable clip Screw x 2 Installing an MSR Turn off the system power. Using two screws to secure the MSR to the right side of the monitor. - Page 20 Hardware Setup Slide out the rear plate (A) and take off the back plate (B). Loosen the screw (C) and slide the unit outwards to reach the main board. C Loosen this screw! On the main board, take off all the jumpers on INT_KBMS port.
- Page 21 Hardware Setup Trace the MSR cable into the unit using the cable clip on top of the fan to secure the cable. Connect the MSR cable to the INT_KBMS port. Cable clip Replace the case, back and rear plate. Screw You may turn the system back on once the MSR is completely installed.
-
Page 22: D 3-In-1 Card Reader Installation
Hardware Setup 2.2d 3-in-1 Card Reader Installation… An optional 3-in-1 Card Reader can be installed on the right side of GT-150 Terminal. Package Content A 3-in-1 Card Reader A metal piece for securing 3-in-1 Card Reader A cable clip Screw x 4 Installing a 3-in-1 Card Reader Note: Before installing a 3-in-1 Card Reader, please make sure the jumper is set correctly on the... - Page 23 Hardware Setup 5. Slide out the rear plate (A) and take off the back plate (B). Loosen the screw (C) and slide the unit outwards to reach the main board. C Loosen this screw! 6. Trace the 3-in-1 Card Reader cable into the unit using the cable clip on top of the fan to secure the cable.
- Page 24 Hardware Setup 7. Replace the case, back and rear plate. Screw 8. You may turn the system back on once the 3-in-1 Card Reader is completely installed.
-
Page 25: Vfd Customer Display Installation
Hardware Setup 2.2e VFD Customer Display Installation… Package Content A VFD VFD Pole x 2 A cable clip A circular base A COM cable Screw x 2 Assemble and Disassemble the Circular pole There are two standard pole heights that may be ordered. You can regulate the height of VFD for your preference. - Page 26 Hardware Setup Installing a VFD Note: Before installing a VFD, please make sure the jumper is set correctly on the main board (Please refer to 2.2a COM power selection). The supply voltage for the customer display should be set to +12V. 1.
- Page 27 Hardware Setup 4. On VFD monitor, there are two cables. Please use the longer one to connect with the COM cable. 5. Position the VFD display into the holder. 6. Connect the VFD COM cable to the COM port. 7. Turn on VFD power switch, and then turn on system power.
-
Page 28: Wifi Installation
Hardware Setup 2.2f WiFi Installation…… An optional WiFi can be installed on the right side of GT-150 Terminal. Package Content A Mini-PCI card A detachable antenna An Antenna line An U-shape base A cable clip Screw x 2 Installing WiFi 1. - Page 29 Hardware Setup 4. Unscrew HD and remove the HD cable. Screw the U-shape base to the unit, and then penetrate the antenna inside. Penetrate the Antenna line into this hole!! 5. Trace the Antenna line into the unit using the cable clip on top of the LPT port to secure the cable.
- Page 30 Hardware Setup 6. Replace the case, back and rear plate. Screw 7. Broken the hole on the back panel and attach the antenna on. 8. You may turn the system back on once the WiFi is completely installed.
-
Page 31: Rfid Installation
Hardware Setup 2.2g RFID Installation…… An optional RFID Card can be installed on the GT-150 Terminal. Package Content A RFID card A RFID cable Screw x 2 Installing RFID 1. Turn off the system power. 2. Loosen the two screws on both sides as the picture shown below. 3. - Page 32 Hardware Setup 4. Remove the RAM card. Screw the RFID card to the system. After RFID card installation, replace the RAM card. 5. On the main board, trace and connect the RFID cable to USB56 port. Important Note: Please face the Remove the RAM card! antenna outward.
- Page 33 Hardware Setup 6. Replace the case, back and rear plate. Screw 7. You may turn the system back on once the RFID card is completely installed.
-
Page 34: Wall Mount Installation
Hardware Setup 2.2h Wall Mount Installation… GT-150 Terminal can be wall-mounted on a flat surface. Package Content A mounting plate Screw x 4 Wall mount Installation 1. Turn off the system power. 2. Select a location with access for cables and a power outlet. 3. -
Page 35: Lcd And Touch Panel Replacement
Hardware Setup 2.3 LCD and Touch Panel Replacement 1. Loosen the screw on the back of the monitor and open the cover. 2. Slide the unit outwards. 3. Unplug all the cables on the rear of the monitor. LVDS connector Touch control board to (for LCD panel) Power connector... - Page 36 Hardware Setup 4. Loosen the two screws from the bracket and the other two screws on the bottom of the device. 5. Loosen the six screws to depart the front cover from the monitor.
- Page 37 Hardware Setup 6. Loosen the four screws (marked in red) to depart the back cover from the monitor. Then, loosen the other four screws (marked in blue) to depart the touch panel from the bracket. Note: Please reverse the steps from step 6 to step 1 to replace the LCD and touch panel. Pay attention to the position of each cable during re-plug (step 3).
-
Page 38: Specification
Specification 3. Specification Technical Information System Model Name GT-150 Motherboard Intel Celeron M 1.2 GHz (Socket 478) System Frequency 400 MHz Chipset Intel 852GM + ICH4 Memory One 184PIN DDR DIMM socket up to 1GB (Support DDR 200/266 unregistered non-ECC) Ethernet 10/100Mbps Ethernet AGP 8X hardware 2D/3D Video Graphic Accelerators Onboard... -
Page 39: Motherboard Configuration
Specification Others Optional Integrated Second 8"/10" LCD Screen without Touch Monitor Device VFD Customer Display MSR Card Reader 3 in 1 (MSR + Smart Card + iButton Reader) WiFi RFID Sound Speaker ＊There is LVDS chip onboard M3 M/B which is responsible for connecting the primary LCD display. However the motherboard it self has one VGA port which then can be responsible for connecting the second LCD display. - Page 40 Specification...