Related Manuals for Longshine CRANE 1
Summary of Contents for Longshine CRANE 1
- Page 1 Tech Manual CRANE 1 Fanless Full Flat Touch Screen POS System Version 1.0 © Copyright LONGSHINE 2023...
-
Page 2: Table Of Contents
Table of Contents System Disassembly…………………………………………….….....3 A Before You Start…………………………………………………………..3 B Remove all the Peripherals (MSR, Customer Display) from the POS Unit.......................4 C Disconnect the Devices from the I/O Ports…………………………….5 a. Unplug the cables from the POS Unit………….……………………..5 D Remove the HDD/SSD Drive from the POS Unit……………………..6 E Detach the Panel Unit (with Main Board) from the Base Unit…….7-9 F Panel Unit (with Main Board Set)...........10-16 a. -
Page 3: System Disassembly
System Disassembly A Before You Start To prevent injuries to the LCD Panel: Carefully place the POS terminal on a flat, clean and stable surface (for example: a stable long table). Prepare additional cushioned material (for example: a soft, clean blanket). ... -
Page 4: B Remove All The Peripherals (Msr, Customer Display) From The Pos
B Remove All the Peripherals (MSR, Customer display) from the POS Unit Please refer to the User Manual for the instructions of installation and disconnection procedures. Pos Unit with MSR Pos Unit with Customer Display Pos unit without optional peripherals Note: Always store the detached parts in a secure location for further use. -
Page 5: Unit
C Disconnect the Devices from the I/O Ports There are some of the optional peripherals or devices installed onto the pos system. Please detach the peripherals/devices and store them in a secure location. Note: Please turn off the whole POS system and devices before unplugging the cables from the I/O Ports. -
Page 6: D Remove The Hdd/Ssd Drive From The Pos Unit
D Remove the HDD/SSD Drive from POS Unit 1. Remove the Protective Cover. 3. Pull out the HDD Drive Module 2. Remove the Screws of the Protective Cover. HDD Drive Module (The appearance of the HDD will vary because of different batches products) -
Page 7: E Detach The Panel Unit (With Main Board) From The Base Unit
E Detach the Panel Unit (with Main Board) from the Base Unit 1. Remove the Two Screws of the Back Cover 2. Lift the Back Cover 3. Disconnect the Cable in the Machine 4. Remove the power switch and SSD slot... - Page 8 power switch (Left) and power switch (right) 5. Remove the Four Screws of the Main board. 6. Remove the VAG interface with 6-point screws. 7. Remove the 3 Screws of the I/O Plate. I/O PLATE...
- Page 9 8. Remove the 6 Screws of the I/O Plate. 9. Touch monitor plate 10. LCD Screen 11. Back shell...
-
Page 10: F Panel Unit (With Main Board Set)
F Back Cover Unit (with Main Board Set) a. Remove the HDD Drive from the Modular Main Board Set 1. Use a screw driver to remove the 4 screws of the metal SSD Slot. Loosen the Securing Screws Back Cover with Main Board on the Metal HDD Slot Metal HDD Slot... -
Page 11: Disconnect The Touch Controller From The Main Board
b. Disconnect the Touch Controller from the Panel Unit 1. Remove the black sticker 2. Disconnect the touch cable from the touch controller 3. Slightly toggle the black fixed switch to loosen the touch cable. 4. Rip off the touch controller (There is double-sided tape under the touch controller) -
Page 12: Remove Main Board From The Panel Unit
d. Remove Main Board from the Back Cover 3. Main Board 1. Use a simple screw driver to remove the 4 screws on the main board 2. Slightly take out the main board from the back cover. -
Page 13: Remove The Ram Module
e. Remove the RAM Module 1. Release the latches on the two sides of the RAM module slot (left). (Ensure the RAM is rise up like the right picture below) 2. Pull and remove the module of the slot with care. RAM Module on the Main Board The RAM Module... -
Page 14: Remove The Metal Bracket Of Bottom I/O Port
Note: Store the RAM Module in a secure location for further use. f. Remove the Metal Bracket of Bottom I/O Port 1. Remove the 4 screws which connect main board and back cover 2. Use a hex screw driver to remove the securing hex spacers of VGA Port. (The two procedures please refer to “c. -
Page 15: Detach The Lcd Panel From The Front Bezel Set
I/O Plate g. Detach the LCD Panel from the Front Bezel Set 1. Remove the securing screws to detach the metal panel bracket from the front bezel set. Front Bezel Set (up) and LCD Panel (down) -
Page 16: Detach The Lcd Panel From The Metal Bracket
h. Detach the LCD Panel from the Metal Bracket 1. Remove the 4 securing screws on the two side of the LCD Panel Panel Bracket and screws... -
Page 17: G Cable Management
G Cable management 1. Remove the bezel upwards 2. Connect the cables and cover the bezel. 3. Pass the CBALE AND WIRE through the hole in the base... -
Page 18: H Assemble The Second Display
H Assemble the second display 1. Detached the second display cover. 2. Connect the cable of the main screen and second display. 3. Second display assemble finished.