Optional Meterbridge - SoundCraft Ghost User Manual

E) Outputs:
15) I’m getting input, but no output
from either the Channel or MIX B
paths.
16) I can’t get a Direct Output from
the Channel DIR/TAPE SND jack.
17) I can’t get a Group Output from
the Channel DIR/TAPE SND jack.
18) There is no output at the AUX
Output jacks.
19) There is no output from the MAIN
MIX, MIX B, or GROUP Output jacks.
20) All the switch settings are correct,
but the MIC/LINE inputs don’t appear
at the MAIN MIX, GROUP, or
DIRECT Outputs.
F) Metering:
21) The MIC/LINE Inputs do not dis-
play on the optional meterbridge
22) The TAPE Inputs do not display on
the optional meterbridge
23) The Group signals do not display
on the GROUP Meters.
24) The MAIN MIX signals do not dis-
play on the CRM/SOLO-L/R Meters.
G) Studio Outputs:
25) Signals can’t be heard at the Studio
Outputs.
10.4
15a) The signal is muted.
15b) The individual fader is down.
15c) The master fader is down.
15d) For the Channels, the signal has
not been assigned to any buses.
16) The jack is being used as a Group
Output.
17) The jack is being used as a Direct
Output.
18) The AUX Sends or AUX Masters
are down.
19) The appropriate master fader is
down.
20a) A plug is connected to a CHAN-
NEL, MAIN MIX, or GROUP Insert
jack, but the other end of the cable is
not connected to a processor.20b) The
Insert Send/Return cable is not con-
nected properly or the outboard
device is not set up properly.
21) The meterbridge is set for TAPE
INPUT METERING.
22) The meterbridge is set for CHAN-
NEL INPUT METERING.
23) The Group Faders are down.
24) The CRM/SOLO-L/R meters do
not automatically display the MAIN
MIX signals; they display the Control
Room Source signals.
25a) You’re using the incorrect STU-
DIO FOLDBACK section or its level
control is down.25b) No Studio Source
has been selected or no signal is avail-
able at the selected source.
15a) Make sure the CUT switch is not
engaged.
15b) Raise the appropriate Channel or
MIX B FADER.
15c) For the Channel: Raise the MIX
and/or GRP 1-8 MASTER FADERS.
For MIX B: Raise the MIX B MASTER
FADER.
15d) Assign the Channel signal using the
Channel Routing Matrix switches and
PAN knob.
16) Make sure the associated DIR/GRP
n switch is set to DIR (UP).
17) Make sure the associated DIR/GRP
n switch is set to GRP n (DOWN).
18) Make sure the appropriate AUX
Sends knobs and associated AUX
Master Faders are turned up.
19) Raise the MIX, MIX B, and/or G1-
8 MASTER FADERS.
20a) Make sure that a plug is not insert-
ed into a CHANNEL, MAIN MIX, or
GROUP INSERT jack, unless you wish
to use an outboard processor on the sig-
nal.
20b) Make sure that the Insert Send is
connected to the outboard device’s
Input jack and the Insert Return is con-
nected to the device’s Output jack, and
that the Input/Output Gain of the device
is properly set up. Also, if the Inserts are
connected to a patchbay, make sure the
Send and Return points are Normalled
on the patchbay.
21) If you want to monitor the Channel
Inputs, see the instructions in this manu-
al for how to set the meterbridge for
CHANNEL INPUT METERING.
22) If you want to monitor the TAPE
Inputs (the default), see the instructions
in this manual for how to set the meter-
bridge for TAPE INPUT METERING.
23) Raise the level of the GROUP
FADERS. The GROUP meters are
located after the GROUP Faders.
24) Select the MIX A switch in the CRM
SRCE section.
25a) Use the STUDIO A section for the
STU O/P A jacks and use STUDIO
B/PHONES for the STU PHNS B
jacks, and make sure their level controls
are turned up.
GHOST Troubleshooting