Table of Contents
Advertisement
Quick Links
Installation Instructions
for Front Control Dryers
Inside.......................................
Dimensions........................................................................
Before You Start................................................................
Installing the Dryer............................................................
Installer Checklist...........................................
Date Purchased ____________________________
Model Number ____________________________
Serial Number _____________________________
Keep these instructions for future reference.
(If this machine changes ownership, this manual must accompany machine.)
www.speedqueen.com
3
4
5
Back Cover
Part No. 512100R6
April 2012
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems ADG41F1
Summary of Contents for Alliance Laundry Systems ADG41F1
-
Page 1: Installation Instructions
Installation Instructions for Front Control Dryers Inside........Dimensions................ Before You Start..............Installing the Dryer............Installer Checklist........... Back Cover Date Purchased ____________________________ Model Number ____________________________ Serial Number _____________________________ Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) Part No. - Page 2 All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100...
- Page 3 (71.1 cm) (68.3 cm) GAS DRYERS DRY2344N *With leveling legs turned into base. NOTE: Exhaust openings are 4 in. (10.2 cm) metal ducting. 3/8 in. NPT Gas Connection © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100...
-
Page 4: Parts Included
5/16 Inch Socket Wrench Duct Tape Teflon Tape (Gas Models) Figure 1 WARNING Any disassembly requiring the use of tools must be performed by a suitably qualified service person. W299 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 5: Installing The Dryer
Outer Wall of Enclosure **NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting easier to connect. Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... - Page 6 DO NOT use sheet metal screws or fasteners on exhaust pipe joints which extend into the duct and catch lint. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100...
-
Page 7: Exhaust Direction
Kit (available as optional equipment at extra cost). • Failure to exhaust dryer properly will void warranty. NOTE: Venting materials are not supplied with the dryer (obtain locally). © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 8: Exhaust System
NOTE: The maximum length of a 4 in. (10.2 cm) diameter flexible metal duct must not exceed 7.87 ft. (2.4 m), as required to meet UL2158, clause 7.3.2A. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 9: Step 3: (Gas Dryer Only) Connect Gas Supply Pipe
Longer than 20 ft. (6.1 m) – reduced to ensure complete combustion. Refer to Use 1/2 in. (12.7 mm) pipe Table 2. 3/8 in. NPT Gas Connection Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 10: Step 4: (Electric Dryer Only) Connect Electrical Plug
Amperes and labeled as suitable for use in a clothes by a qualified electrician. dryer. NOTE: The wiring diagram is located behind the control panel, inside the control cabinet. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... - Page 11 The power cord connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of power cord and gauge of wire must conform to local codes. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100...
-
Page 12: Connecting Power Cord With Three-Wire Plug
3. Use a strain relief and insert end of power cord through power supply hole. 2. Remove access cover from rear of dryer. D696I D695I Figure 8 Figure 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 13: Connecting Power Cord With Four-Wire Plug
8. Reinstall access cover and screw. DRY2467N Figure 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... - Page 14 10. Reinstall access cover and screw. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100...
-
Page 15: Step 5: Reverse Door, If Desired
8. Using screwdriver, remove two door plugs, and reinstall on opposite side of door opening. DRY1916N DRY1916N 4. Rotate door panel 180 degrees as shown. DRY2052N DRY2052N D273P © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 16: Gas Dryer
120 Volts AC (alternating current) 15 Amps. Refer to Figure 17 to determine correct polarity of the wall receptacle. D275I Connect to 30 Amp circuit. D275I Figure 16 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 17: Step 8: Recheck Steps
To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the dryer to the electrical power source. W037 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 18: Gas Dryers
Adjust the air shutter as follows: D702I D702I Air Shutter Lockscrew Air Shutter Appliance Main Gas Valve 1/8 in. (3.1 mm) Pipe Plug (For checking manifold pressure) Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512100... -
Page 20: Installer Checklist
Gas Leaks. CHECK D258I CHECK • Check Heat Source. ELECTRIC ONLY • Connect Electrical Cord. D702I D702I CHECK CHECK W315IE0A D699I • Reverse Door, if Desired. DRY2051N CHECK DRY2051N © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Need help?
Do you have a question about the ADG41F1 and is the answer not in the manual?
Questions and answers