Installing Outside Lever On Non-Mechanical Override; Reversing The Outside Lever For Series Without Mechanical Override - Kaba e-plex 2000 Installation Instructions Manual

Door Thickness Table
Door
Thickness
3 9
⁄ " ⁄ " (
1 (35 mm) up to 1 40 mm)
8 16
9 ⁄ "
Over 1 (40 mm) to less than
16
11
⁄ "
1 (43 mm)
16
3 ⁄ " (
1 44 mm) Door
4
11
1 ⁄ " ( 43 mm) to less than
16
7
⁄ "
1 (48 mm)
8
7 ⁄ " 15 ⁄ "
1 (48 mm) to 1 (49 mm)
8 16
2" (50 mm) Door
15 ⁄ " (49 mm)
over 1 to less than
16
1
2 ⁄ " ( 54 mm)
8
1 3
⁄ " ⁄ "
2 (54 mm) to 2 (56 mm)
8 16
1
⁄ "
2 (57 mm) Door
4
3 3
⁄ " ⁄ "
over 2 (56 mm) to 2 (60 mm)
16 8
3 1
⁄ " ⁄ "
Over 2 (60 mm) to 2 (64 mm)
8 2
Screw Length Full Scale
3
Length ⁄ "
(10 mm)
8
1
Length ⁄ "
(13 mm)
2
5 ⁄ "
Length (16 mm)
8
3
Length ⁄ "
(19 mm)
4
7 ⁄ "
Length (22 mm)
8
D. INSTALLING OUTSIDE LEVER ON
NON-MECHANICAL OVERRIDE
Assemble the lever on the outside housing in the hori-
zontal rest position appropriate to the handing of the
door. Simply push the lever onto the tube until it clicks
in place. If more force is required, use a rubber mallet.
Test the attachment of the handle by pulling on it to
make sure it is securely fastened.
8
Spacer 02 Spacer 04 Spacer 05
thin 125 328
- 1 -
- 2 -
1 2 -
1 - 1
2 - 1
- 1 1
2 1 1
- - 2
E. REVERSING THE OUTSIDE
LEVER FOR SERIES WITHOUT
Screw
MECHANICAL OVERRIDE
length
The lever is field reversible. If the handing is
3
⁄ "
(10 mm)
8
incorrect, insert a small pick or flat screwdriver in the
1 ⁄ " (
13 mm)
2
hole in the hub as shown. Gently pry back the spring
clip inside the hub, and remove the handle.
5
⁄ " ( 16 mm)
8
5 ⁄ " (
16 mm)
8
3 ⁄ " (
19 mm)
4
F. INSTALLING OPTIONAL KEY OVERRIDE AND
3
⁄ " (
19 mm)
OUTSIDE LEVER
4
7
⁄ " (
22 mm)
8
Important: Assemble the lever, cylinder and lock components before affixing
7
⁄ " (
22 mm)
the entire unit to the door.
8
F-1 Upon unpacking, the lock housing with mechanical override should look
like the diagram below with:
• The small indents (i) on the cross of the override shaft (m) in line
horizontally
• The nylon washer (c) and the spring washer (d) on the drive tube
• The lever catch (f) in the out position
• Cylinder (j) and 2 keys (n) included in the hardware bag
(i)
(f)
(c, d)
(m)
(n) (j)
9