Ace Receiver Wiring & Jumper Options - GARDINER TECHNOLOGY Gardtec 800 Installation Instructions Manual

Wiring Connections
JP 5 to JP8 (applicable to later multi-purpose keypads only)
Note: some of these jumpers may not be fitted on versions without ACE
JP 5 (ACE User Select) ACE units only
This jumper is the user select. With the jumper link removed each ACE key fob will
occupy one user code from the system, this is termed as high security mode.
With the jumper link in position the ACE will occupy one user code from the system but
up to fourteen key fobs may be programmed into the ACE, this is normal security
mode.
JP 6 (Reset) ACE units only
The ACE has a Non-Volatile Memory (NVM). If power is applied to the unit with this
jumper in position, the memory contents will be erased. When the unit is first powered
up, this jumper should be in position for at least 5 seconds. After this initial period the
jumper link should be removed.
If a reset of the ACE is required (all fobs to be deleted) this jumper link should be
refitted and the unit re-powered.
JP 7 (Panel Type Select)
This jumper selects the keypad as Gardtec 580 or Gardtec 800 series. With the
jumper in position the keypad will be Gardtec 580 compatible. With the jumper
removed the keypad will be Gardtec 800 Series compatible.
JP 8 (EOL)
This jumper is the End Of Line jumper and is applicable to the Gardtec 350+ and
Gardtec 580 only. This jumper MUST BE REMOVED when used with the Gardtec
800 Series .
Note: Instructions for how to program keyfobs to the ACE and using ACE are
contained within the LED user manual
Page
GARDTEC 800 Series
20
GARDTEC 800 Series
ACE Receiver Wiring & Jumper Options
ACE is also available as a stand alone receiver. The wiring for the receiver is the same
as for the RKP(s) with the exception that the speaker wiring terminal on the ACE is
marked as SP- and not SPKR.
The ACE receiver is link selectable as unit No.1 or unit No.2 and it is permissible to
have two units sharing the same ident.
Five options are available that are selected with jumper links.These options are as
follows.
JP1 (US)
This jumper is the user select. With the jumper link removed each ACE key fob will
occupy one user code from the system, this is termed as high security mode.
With the jumper link in position the ACE will occupy one user code from the system but
up to fourteen key fobs may be programmed into the ACE, this is normal security
mode.
JP2 (RP)
This jumper is only used when the ACE is fitted to the Gardtec 800 Series control
panels and is used to select the ACE ident as 1 or 2 . This ident should be viewed as
the RKP ident. With the jumper off the ACE will be remote device two, with the jumper
fitted the ACE will be device number one.
JP3 (PN)
This jumper is used to select the panel type when ACE is used with the Gardtec 350+
or Gardtec 580 control panels. The jumper has no use when used with the Gardtec
800 Series and should be left in position.
JP4 (RST)
The ACE has a Non-Volatile Memory (NVM). If power is applied to the unit with this
jumper in position, the memory contents will be erased. When the unit is first powered
up, this jumper should be in position for at least 5 seconds. After this initial period the
jumper link should be removed.
If a reset of the ACE is required (all fobs to be deleted) this jumper link should be
refitted and the unit re-powered.
JP5 (EOL)
This jumper is the End Of Line jumper and is applicable to the Gardtec 350+ and
Gardtec 580 only. This jumper MUST BE REMOVED when used with the Gardtec
800 Series .
Note: Ensure all links are in desired position before powering up the ACE.
Page
Wiring Connections
21