Warnings And Cautions - Wolf OG36-LP Technical & Service Manual

Component Access / Removal
COMPONENT ACCESS AND REMOVAL
This section explains how to access and remove components. Since there are only slight variations between each
of the OG models, diagrams of the model OG42 are used in most cases.
An attempt has been made to arrange these procedures in such a way as to simulate which components would
need to be removed first in order to gain access to other components. When following a component removal proce-
dure, it may be necessary to reference another component removal procedure listed earlier in this section.
IMPORTANT NOTE: Before continuing, take note of the WARNINGS and CAUTIONS below.
Components
Halogen Lamp................................................................... 4-3
Drip Pan Assembly .......................................................... 4-3
Thermometer ..................................................................
Handle and End Caps ...................................................... 4-4
Grates .............................................................................. 4-4
Briquette Trays ................................................................. 4-4
Zone Dividers ................................................................... 4-4
Burner Flash Tubes .......................................................... 4-5
Burner (Main and Sear) ................................................... 4-5
Control Knobs .................................................................. 4-5
Control Knob Bezels ........................................................ 4-6
Front Panel Assembly ...................................................... 4-6
Lights Power Switch ......................................................... 4-6
Front Panel LED Lights .................................................... 4-7
• TO AVOID SERIOUS BURN INJURIES OR DEATH FROM FLAMES AND/OR EXPLOSIONS:
- KEEP COMBUSTIBLES AWAY FROM THE APPLIANCE WHENEVER A FLAME IS PRESENT.
- IF IGNITING THE GRILL DURING SERVICE, KEEP FACE AND LIMBS AWAY FROM ABOVE THE GRATE
SURFACE.
- KEEP IN MIND THAT GRILL SURFACES AND COMPONENTS GET HOT DURING USE OF THE APPLI-
ANCE. DO NOT TOUCH HOT SURFACES OR HOT COMPONENTS WITH BARE SKIN. USE PROPER
PROTECTIVE CLOTHING WHEN REMOVING OR ADJUSTING HOT COMPONENTS.
- WHENEVER REMOVING A GAS VALVE OR GAS REGULATOR, ALWAYS SWITCH THE GAS SUPPLY
TO THE UNIT OFF FIRST.
- IF MOVING THE GRILL DURING SERVICE, ALWAYS SWITCH THE GAS SUPPLY TO THE UNIT OFF
FIRST, AND TAKE CARE TO NOT DAMAGE THE GAS SUPPLY LINE.
- WHEN REASSEMBLING THE GAS SUPPLY LINE TO THE REGULATOR, OR THE REGULATOR TO THE
MANIFOLD, USE ONLY PIPE THREAD COMPOUND. NEVER USE TEFLON TAPE TO SEAL GAS PIPE
CONNECTIONS.
• IF PULLING A UNIT FROM ITS INSTALLATION OR CART, REMEMBER THAT IT IS EXTREMELY HEAVY AND
COULD TIP AND FALL RESULTING IN SERIOUS INJURY OR DEATH. PULLING A UNIT FROM ITS INSTAL-
LATION OR CART SHOULD ONLY BE PERFORMED BY AN AUTHORIZED SERVICE TECHNICIAN OR
INSTALLER.
• TO AVOID ELECTRIC SHOCK, POWER TO THE UNIT MUST BE DISCONNECTED WHENEVER ACCESSING
AND/OR REMOVING COMPONENTS POWERED BY ELECTRICITY OR COMPONENTS NEAR OTHER
ELECTRICAL COMPONENTS.
• Some components on the appliance may have sharp edges.
#814144 - Revision A - July, 2009
Outdoor Grill (OG) Series
This section is arranged as follows
Page Components
Burner Hot Surface (Glow) Igniters .................................. 4-7
Valve Micro-Switch ........................................................... 4-7
4-3 Gas Burner Orifice ........................................................... 4-8
Gas Burner Valve Assembly ............................................. 4-8
Gas Regulator (Natural Gas - Convertible) ..................... 4-9
Landing Ledge (aka Bullnose) ........................................... 4-9
Hood Assembly and/or hood Springs ............................. 4-10
Rear Hood Shell ............................................................. 4-10
Rotisserie Burner Orifice ................................................ 4-11
IR Rotisserie Burner ....................................................... 4-11
Rotisserie Burner Gas Line ............................................ 4-11
Rotisserie Burner Igniter ................................................ 4-12
Halogen Lamp Assembly (Light Socket) ........................ 4-13
Hood Switch ................................................................... 4-13
4-2
Page