Dynamic Signaling Field; Output And System Setup - Safewatch QuickConnect Plus Programming Manual

Data Field Display
74 74 74 74
LO LO LO LO BAT BAT RES RES REP REP
BAT BAT RES RES REP REP
75 75 75 75
RF RF RF RF LOBAT LOBAT R R R R ES ES ES ES REP REP
LOBAT LOBAT REP REP
76 76 76 76
TEST TEST RES RES REPORT REPORT
TEST TEST RES RES REPORT REPORT

DYNAMIC SIGNALING FIELD (677)

77 77 77 77
DYNAMIC SIG OPTS DYNAMIC SIG OPTS DYNAMIC SIG OPTS DYNAMIC SIG OPTS
7 7 7 7 8 8 8 8
PROG TONE GEN TM PROG TONE GEN TM
PROG TONE GEN TM PROG TONE GEN TM
OUTPUT AND SYSTEM SETUP (680, 681, 683–685) See Procedures later in this manual.
86 86 86 86
MULTI MULTI MULTI MULTI- - - - MODE MODE MODE MODE EMAIL EMAIL EMAIL EMAIL
87 87 87 87
AUX FUNC AUX FUNC 1BTN 1BTN PG PG PG PG
AUX AUX FUNC FUNC 1BTN 1BTN
88 88 88 88
PAGER CHARACTERS PAGER CHARACTERS PAGER CHARACTERS PAGER CHARACTERS
89 89 89 89
EVNT EVNT LOG LOG 80% 80% REP REP
EVNT EVNT LOG LOG 80% 80% REP REP
Function& Programming Options [ ] = Programmed Table 1 Default Values
Low Bat Restore Report Code
| [1,0]
RF Transmitter Low Battery Restore Report Code
| [1,0]
Test Restore Report Code
| [1,0]
Dynamic Signaling Options
| [0, 0]
1st Entry (delay before switch CS reporting path)
0 = Redundant
reporting on dialer
and LRR/IP device
1 = 15 seconds
2 = 30 seconds
2nd Entry
0 = Primary Dialer
Preferred Channel
Programmable Tone Generation Time
| [0, 0]
00 = Disabled
01-09 = 100-900 ms
10-99 = 1.0 – 9.9 secs
Multi-Mode (E-Mail Notification) (RIS is always enabled)
[0]
0 = Disable multi-mode devices (RIS enabled)
1 = Enable multi-mode device address #6 only (RIS enabled)
2 = Enable multi-mode device address #7 only (RIS enabled)
3 = Enable multi-mode addresses (RIS enabled)
Aux Function/ 1-Button Paging
[0]
0 = Aux key performs defined function (macro);
1 = Aux key sends message to pager or voice message to follow me system phone no.
If 1, you must also select an option 6-9 in field 649 for the pager or 10-13 for the follow me
system announcement.
Pager Characters
Up to 16 digits can be entered that will appear in front of the 7-digit pager message sent by
the control. Refer to the Installation Instructions (fields 687, 688 and 649) for full
descriptions of the paging feature. You do not need to fill all 16 digits (press [6] to
advance to next field).
To clear entries, enter 6886. To enter "6" = [#] + [11]; To enter "#" = [#] + 12]; To
enter 2-second pause = [#] + [13] (some pagers require an additional delay [pause] in
order to receive the entire message)
Event Log 80% Full Report Code
| [0,0]
3 = 45 seconds 8 = 120 seconds
4 = 60 seconds 9 = 135 seconds
5 = 75 seconds #10 = 150 seconds
6 = 90 seconds #11 = 165 seconds
7 = 105 seconds #12 = 180 seconds
1 = LRR/IP 2 = LRR/IP
Preferred Channel reporting only
- 9 -
#13 = 195 seconds
#14 = 210 seconds
#15 = 225 seconds