Safewatch QuickConnect Plus Programming Manual page 6

Data Field Display
46 46 46 46
FOLLOW ME PHONE FOLLOW ME PHONE
FOLLOW ME PHONE FOLLOW ME PHONE
#
47 47 47 47
PHONE SYS SELECT PHONE SYS SELECT
PHONE SYS SELECT PHONE SYS SELECT
48 48 48 48
REP FRMT PRI/ REP FRMT PRI/SEC SEC
REP FRMT PRI/ REP FRMT PRI/ SEC SEC
49 49 49 49
SPLIT/DUAL SPLIT/DUAL SPLIT/DUAL SPLIT/DUAL REP REP REP REP
50 50 50 50
ABORT WINDOW ABORT WINDOW ABORT WINDOW ABORT WINDOW
Function& Programming Options
"Follow Me" Reminder Phone Number
Enter up to 24 digits; Do not fill unused spaces. If fewer than 24 digits entered, pressing 6
advances to the next field. To clear entries from field, press 6466.
Enter 0-9, #+11 for '6'; #+12 for '#'; #+13 for a pause (two seconds).
Phone System Select
† [5]
Central
Station Pulse
0 = No Speaker
No WATS
Phone
2 = No Speaker
WATS
Phone
Report Format for Primary/Secondary
[7, 7]
Primary Secondary
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1 = 3+1, 4+1 RADIONICS STANDARD
2 = 4+2 ADEMCO L/S STANDARD
3 = 4+2 RADIONICS STANDARD
5 = ADEMCO CONTACT ID® REPORTING
WITH 10-DIGIT SUBS ACCT NO.
Split/Dual Reporting
[0]
To Primary Phone No.
0 = All reports
1 = Alarms, Restore, Cancel
2 = All except Open/Close, Test
3 = Alarms, Restore, Cancel
4 = All except Open/Close, Test
5 = All
To Primary Phone No.
6 = All reports except Open/Close
7 = All reports
8 = All reports
9 = All reports except Open/Close
To Primary Phone No.
10 = All except Open/Close
11 = All reports
12 = All reports
13 = All except Open/Close
‡ Will report users 0, 5-8 or wireless arm/disarm button zones 26-33; all other zones and users do not
report.
Burglary Abort Window
† [2]
1 = 15-second abort window
2 = 30-second abort window
3 = 45-second abort window
SIA The sum of the burglary abort window entered in 650 and the entry delays entered in either Field
635 or 636 should not exceed 1 minute.
Note: The control validates the data entered in this field. If the selection is not valid the control emits a
single long beep indicating that the selection has been rejected. The control replaces the selection
with the default value "2", which is displayed on the keypad, and advances to the next field.
[ ] = Programmed Table 1 Default Values
Note: If you are using Pulse (rotary) Dialing, you must enter the
numbers slowly to allow the pulse dialer time to operate.
Dialing Mode
Tone Pulse
1 = No 4 = With
Speaker Phone Speaker
Phone
3 = No 6 = With
Speaker Phone Speaker Phone
Note: Option 5 or 7 (ADEMCO Contact ID®)
6 or undefined = 4+2 ADEMCO EXPRESS
7 = ADEMCO CONTACT ID® REPORTING
WITH 4-DIGIT SUBS ACCT NO.
8 = 3+1, 4+1 ADEMCO L/S EXPANDED
9 = 3+1, 4+1 RADIONICS EXPANDED
To Secondary Phone No.
None, unless primary fails, then all
Others
Open/Close, Test
All
All
All
To Paging Number
Alarms, Open/Close‡, Troubles
Alarms, Troubles
Alarms, Open/Close‡, Troubles
Alarms, Troubles
To Follow Me System Phone Number)
Alarms, Open/Close‡, Troubles
Alarms, Troubles
Alarms, Open/Close‡, Troubles
Open/Close‡
- 6 -
Tone
5 = With
Speaker Phone
7 = With
Speaker Phone
must be selected for AAV.