Frothing Milk; Machine Cleaning Program; Maintaining Your Appliance; Maintenance - Krups EA80 series User Manual

KR_ESPRESSO_EA80_EE_OA21003_Mise en page 1 09/12/13 13:58 Page6

Frothing milk

We recommend that you use pasteurised or UHT milk that has been recently opened. Untreated milk does not give
the best results. After the steam function has been used, the nozzle can be hot, and we recommend that you wait for
a few moments before handling it.
Pour the milk into your milk jug. Immerse the nozzle in the milk - Fig. 19.
Initiate the steam function as explained in the paragraph above.
Once your milk is frothy enough... - Fig. 20 ... ...again press the
To remove any remaining milk from the steam nozzle, place a receptacle under the nozzle and press the
steam escape for at least 10 seconds and then again press the
The steam nozzle can be removed for more intense cleaning. Wash it out with water and a little washing up liquid and a
small non-abrasive brush. Rinse and dry it - Fig. 21. Before putting it back, ensure that the air inlet holes are not blocked
by any milk residues. If necessary, unblock them using the needle supplied- Fig. 22. Do not wash the steam nozzle in the
dishwasher.
To interrupt the steam function, just press any key. Be careful as the nozzle may be hot. If the nozzle is blocked,
unblock it using the needle supplied. The maximum duration for production of steam per cycle is limited to 2 minutes.
Emptying the coffee grounds collector, the coffee tray and the drip tray
If the light comes on, remove, empty and clean the drip tray.
Remove, empty and clean the coffee grounds collector.
Remove the coffee cleaning tray.
The drip tray is equipped with floats to tell you when to empty it.
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
The light will remain on if the coffee grounds collector is not slotted in fully or not fitted correctly or if
it has been put back in less than 4 seconds. You cannot make espresso or coffee while the
flashing. The coffee grounds collector has a capacity of 9 coffees.
Rinsing out the circuits: see page 14
Machine cleaning program – total duration: about 20 minutes
When a cleaning operation is necessary, the appliance warns you of this by flashing the "clean" light.
This program is only accessible when the machine requests it (i.e. approximately every 300 coffees or espressos).
Caution! To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle when
informed to do so. Be sure to follow the procedure closely, step by step. You can continue to use the appliance
when the light is on, but you are advised to perform the program as soon as possible.
Press the 'Service' button to start up the cleaning program. The 'clean' and
Remove and clean the cleaning tray then fit it again - Fig. 23.
Empty and clean the coffee grounds collector then fit it again - Fig. 24. The
Remove and empty the drip tray - Fig. 25.
Remove, fill and re-fit the water tank.
Place a receptacle with a minimum capacity of 0.6 l under the coffee outlets- Fig. 26.
Open the servicing flap and insert a KRUPS cleaning tablet (XS3000) in the cleaning inlet - Fig. 27.
Press the 'Service' button to start up the cleaning program.
1 - Cleaning cycle ± 10 mn
The 'clean' light becomes steady. The cleaning cycle will be run automatically. The pump sucks up water
intermittently. This operation lasts about 10 minutes and the 'clean' light will flash again.
Empty your waste water receptacle and put it back under the coffee outlets.
Again press the 'Service' button to start the first rinsing cycle.
2 - First rinsing ± 5 mn
The 'clean' light will become steady again. The program continues. A first rinsing cycle will be run automatically.
It allows the appliance to be rinsed and remaining detergent to be eliminated. This first rinsing cycle lasts about
5 minutes and once finished the 'clean' light will flash again.
Empty your waste water receptacle and put it back under the coffee outlets.
Again press the 'Service' button to start the second rinsing cycle.
6

MAINTAINING YOUR APPLIANCE

key to stop the cycle.
key to stop the process.
lights will flash.
light will go off.
key. Let the
light is on or is