Table of Contents
Advertisement
Installing cooker – power connections
Fitting on a Power Supply Cable
WARNING:
Installtion MUST ONLY be carried out by a qualified approved installer, ie. an Electrician.
Connecting appropriate power supply ` terminal boar d/ connector block:
NOTE:
REFER to TECHNICAL tables at the rear of this manual for correct rating for your
corresponding model purchased.
•
Using a screwdriver, prize open tabs of the Terminal board cover.
•
Remove the wire clamp screw.
•
Fasten the wires beneath the corresponding screw heads, using the brass 'bridge' for 1 phase supply or 2 phase
supply.
•
Fasten cable clamp and close the cover of the terminal board.
•
The AC power supply should be 220-240V, 50Hz. For electric cookers, the minimum is a 45A fuse, or at least 45A
a distribution circuit breaker. For gas cookers, the minimum is a 20A fuse, or at least 20A circuit breaker.
WARNING: Connect the power supply cable must be in accordance with the instructions listed in the table below
Wire cross-sectional
area (mm
)
2
L1
Connection mode
1N~
Min 6
2N~
Min 1.5
Connecting the supply cable to the mains
Install an approved circuit breaker with a minimum contact opening of 3 mm, between the appliance and the mains
fuse box. The circuit breaker should be sized according to the load and should comply with current regulations (the
earth wire should not be interrupted by the circuit breaker).
The supply cable should be positioned so that it does not reach a temperature of more than 50ºC with respect to the
room temperature, anywhere along its length Before switching fuse ON in meter-box check:
•
Earth continuity. The electrical safety of this appliance can only be guaranteed if the cooker is correctly installed
and earthed, in compliance with regulations on electrical installations.
•
The electrical capacity of the system and sockets will support the maximum power of the appliance, as indicated
on the data plate
NOTE: All Upright cookers must comply to local regulations to Australian Standard AS/NZS 3000:2007
guidelines. Qualified Electrician will have a copy of these guides that MUST be adhered to.
26 Baumatic 540mm Upright Cooker INSTALLING COOKER – POWER CONNECTIONS
L2
N
E
—
Min 6
Min 6
Min 2.5
Min 6
Min 6
Installing the gas cooker
Unpacking
Do not fit the burner crowns, burner caps and trivets
until after the cooker has been installed.
Checking gas pressures
Before installation check that the cooker is suitable for
the gas supply. To do this check the gas type on the
carton sticker or on the data plate behind the bottom of
the oven door.
Before connecting gas supply
The following shows the supply and operating
pressures for various gas supplies.
Operate pressure at appliance test point:
1.00 KPa (Natural gas); 2.75 KPa (Universal LPG gas)
The following table shows the injector sizes for each
burner.
Injector
Natural gas
Universal LPG
Auxiliary burner
0.93mm
0.57mm
Semi-rapid Burner
1.16mm
0.71mm
Triple ring Burner
1.75mm
1.10mm
Connection to the gas supply
The gas Connection must be made in accordance
■
with the local standards.
When installing, fit a safety tap at the end of the
pipeline. The appliance leaves the factory tested
and set for the type of gas indicated on the
plate inside the bottom guard, close to the gas
connection pipe. Make sure that the type of gas to
be supplied to the appliance is the same as that
shown on the plate.
For maximum efficiency and minimum consumption,
■
make sure that the gas supply pressure complies
with the values shown in the gas used is different
from that specified (or variable).a suitable pressure
regulator must be installed on the supply pipeline.
Gas connection
A
Inlet pipe joint
B Gasket
C Stable union
Procedure
Make the connection to the gas system using a rigid
metal pipe and regulation unions, or with a stainless
steel hose complying with the local standard. If metal
hoses are used, take care that they do not come into
contact with mobile parts and are not crushed.
When making the connection, take care not to apply
stresses of any kind to the appliance.
Read these points before connecting to the gas supply;
•
The gas connection point is a 1/2" BSP external
thread located at the rear of the appliance as shown
in the Rear View.
•
A regulator is supplied for natural gas appliances
which must be fitted in the supply line to the
appliance. For LPG the supplied brass Test Point
Adapter / Fitting must be fitted to the supply line.
•
It is recommended to fit the regulator or test point
fitting to the appliance connection point, then fit
either hard piping or a flexible connection from
the regulator or test point fitting to consumer hard
piping. Ensure installation allows withdrawal of
appliance. For flexible hose installation AS/NZS
5601.1 clauses 5.9 and 6.10.1.9 must be followed.
Baumatic 540mm Upright Cooker INSTALLING THE GAS COOKER 27
Hide quick links:
Advertisement
Table of Contents
