Download Print this page

Advertisement

Operating and installation instructions
Induction wok
CS 1223-1
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 09 551 700

Advertisement

   Also See for Miele CS 1223-1

   Summary of Contents for Miele CS 1223-1

  • Page 1

    Operating and installation instructions Induction wok CS 1223-1 en - GB To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 09 551 700...

  • Page 2: Table Of Contents

    Contents Guide to the appliance ..........4 Warning and Safety instructions .

  • Page 3

    Contents Appliance and building-in dimensions ....... 35 Preparing the worktop ..........36 Installation of several appliances.

  • Page 4: Guide To The Appliance

    Guide to the appliance a Wok basin Indicators (C) 300 mm / rating: normal: 2400 W with Booster: 3200 W b Wok f In-operation indicator c Control g Booster indicator d Indicators h Residual heat indicator e Display...

  • Page 5

    Guide to the appliance Display ß No wok on cooking zone, or wok unsuitable Auto heat-up Fault message (See "Problem solving guide") C / 0 Safety switch-off (See "Safety features") Booster in operation Overheating protection (See "Safety features") Lock (see "Safety features") Accessories supplied Wok (CSWP 1400) Wok rest...

  • Page 6: Warning And Safety Instructions

    They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Keep these instructions in a safe place and ensure that new users...

  • Page 7

    Warning and Safety instructions Correct application The wok is not designed for commercial use. It is intended for use in domestic households and similar working and residential environments. The appliance is not intended for outdoor use. It is intended for domestic use only to cook food and keep it warm.

  • Page 8

    Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the wok unless they are constantly supervised. Children 8 years and older may only use the wok if they have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation.

  • Page 9

    Warning and Safety instructions Technical safety Installation, maintenance and repairs may only be carried out by a Miele authorised service technician. A damaged appliance could be dangerous. Before installation, check the appliance for visible signs of damage. Do not use a damaged appliance.

  • Page 10

    The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used. Faulty components must only be replaced by genuine Miele original spare parts. The wok is not intended for use with an external timer switch or a remote control system.

  • Page 11

    Warning and Safety instructions Correct use Oil and fat can overheat and catch fire. Never leave the appliance unattended when cooking with oil or fat. If oil or fat does catch fire, do not attempt to put out the flames with water.

  • Page 12

    Warning and Safety instructions If the wok is installed behind a kitchen furniture door, it may only be used with the furniture door open. Do not close the door whilst the appliance is in use or whilst there is any residual heat present. The wok gets hot when in use and remains hot for quite a while after being switched off.

  • Page 13

    Warning and Safety instructions Wok pans which boil dry can cause damage to the ceramic glass. Do not leave the appliance unattended whilst it is being used. Grains of salt, sugar and sand (e.g. from cleaning vegetables) can cause scratches if they get under pan bases. Make sure that the ceramic surface is clean before placing pans on it.

  • Page 14

    Warning and Safety instructions To prevent damage to items which are susceptible to magnetic fields, e.g. credit cards, digital storage devices, pocket calculators, etc, do not leave them in the immediate vicinity of the wok. Metal utensils stored in a drawer under the wok can become hot if it is used intensively for a long time.

  • Page 15: Caring For The Environment

    Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The packaging is designed to protect handled or disposed of incorrectly the appliance from damage during could be potentially hazardous to transportation.

  • Page 16: Before Using For The First Time

    Before using for the first time Before using for the first time Please stick the extra data plate for the appliance supplied with this When the induction wok is first documentation in the space provided in connected, and after a power cut, all of the "After sales service, data plate, the indicators in the display light up for guarantee"...

  • Page 17: Induction

    Induction The induction principle Take particular care never to place An induction coil is located underneath cutlery or other metal objects on the the induction wok. When the appliance appliance. When the appliance is is switched on, this coil creates a switched on either deliberately or by magnetic field.

  • Page 18: Pans

    Induction Pans Noises The following noises might occur when Only use the wok supplied with the the induction wok is in operation: appliance for cooking food. This wok is designed specifically for the – On the higher power settings, it appliance.

  • Page 19: Operation

    Operation Switching on and off Residual heat indicator The induction wok is switched on by The residual heat indicator remains on turning the control clockwise a to the until the induction wok is cool enough power setting required, and is switched to touch.

  • Page 20: Settings

    Operation Settings Activating Auto heat-up ^ Turn the control anti-clockwise as far Cooking process Settings as it will go and hold in that Keeping food warm, 1 - 2 position until A appears in the melting chocolate display. Warming food up 3 - 6 If you hold the control for too long, L Stir-frying, e.g.

  • Page 21: Booster Function

    Operation Booster function To switch on the booster function ^ Turn the control past power setting 9 The induction wok is equipped with a booster function which increases the to BI, and then back to 9. power level. I will appear in the display for the If activated, the appliance will operate cooking zone and the B booster on power setting 9 with an extra boost...

  • Page 22: Safety Features

    Safety features System lock To deactivate the system lock ^ Turn the control anti-clockwise as far The induction wok is fitted with a system lock to prevent unauthorised as it will go, and hold in that position until the L goes out, and 0 appears use, e.g.

  • Page 23: Safety Switch-off

    Safety features Safety switch-off Power setting Maximum The induction wok is fitted with a safety operating time in switch-off feature in case you forget to hours switch it off yourself. If the induction wok is heated for an unusually long period of time (see chart), and the power setting is not altered, it will switch itself off automatically.

  • Page 24: Overheating Protection

    Safety features Overheating protection The induction coil can overheat if The induction coil is equipped with – the appliance is used for too long at overheating protection. Before the maximum power. induction coil gets too hot, overheating – the appliance is not well enough protection cuts in in one of the following ventilated.

  • Page 25: Cleaning And Care

    Cleaning and care Miele offer a range of branded cleaning To avoid damaging the surface of and conditioning products. See your appliance, do not use: "Optional accessories". – cleaning agents containing soda, alkalines, ammonia, acids or Do not use a steam cleaning chlorides, appliance to clean this appliance.

  • Page 26: Ceramic Surface

    Stubborn soiling may need Stainless steel to be removed with a shielded scraper blade. Miele's ceramic and stainless steel hob cleaning agent is suitable for cleaning Then clean the appliance with Miele stainless steel surfaces (see "Optional ceramic and stainless steel hob accessories").

  • Page 27: Problem Solving Guide

    Check whether the control is damaged – the system lock is activated. or stuck. If necessary, deactivate it (see If this is not the case, call the Miele "System lock"). Service Dept. – the mains fuse has tripped. – the overheating protection mechanism has been triggered (see ...

  • Page 28

    Problem solving guide ... one of the following has occurred: ... the cooling fan continues to run after the appliance has been – The booster has automatically switched off. switched off early. This is not a fault. The fan will continue –...

  • Page 29: Optional Accessories

    Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These products can be ordered online at: or from Miele (see back cover for contact details) Wok pan CSWP 1400...

  • Page 30: Safety Instructions For Installation

    The high temperatures radiated by the wok could damage the appliance below. The appliance may only be built in over a Miele oven if the worktop is at least 40 mm thick.

  • Page 31

    Safety instructions for installation Safety distance above the appliance When two or more appliances which have different safety distances are installed together below a cooker hood, you should observe the greater safety distance of the two. A minimum safety distance must be maintained between the appliance and the cooker hood above it.

  • Page 32

    40 mm CS 1212 / CS 1212-1 CS 1221 / CS 1221-1 CS 1234 / CS 1234-1 CS 1223 / CS 1223-1 CS 1222 50 mm CS 1112 Not recommended CS 1122...

  • Page 33

    Safety instructions for installation Safety distances underneath the hob Interim shelf To ensure sufficient ventilation to the It is not necessary to fit an interim shelf hob, a certain gap must be left between underneath the hob, but one may be the underside of the hob and any oven, fitted if you wish.

  • Page 34

    Safety instructions for installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding.

  • Page 35: Appliance And Building-in Dimensions

    Appliance and building-in dimensions CS 1223-1 a Spring clamps b Front c Casing depth d Mains connection cable, L = 2000 mm...

  • Page 36: Preparing The Worktop

    Preparing the worktop ^ Make the worktop cut-out for one or more appliances in accordance with the building-in diagrams. Remember to maintain a minimum safety distance from the back wall, as well as from any tall unit or side wall to the right or left of the appliance.

  • Page 37: Installation Of Several Appliances

    Installation of several appliances When installing two or more appliances next to each other a spacer bar b must be used between each one. See "Fixing the spring clamps and spacer bars". Worktop cut-out Worktop cut-out - two appliances - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.g.

  • Page 38

    Installation of several appliances a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances. An additional spacer bar is required for each additional appliance. The position for securing each additional spacer bar will depend on the width of appliance B (288 mm / 380 mm / 576 mm).

  • Page 39: Fixing The Spring Clamps And Spacer Bars

    Fixing the spring clamps and spacer bars Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied.

  • Page 40

    Fixing the spring clamps and spacer bars Granite and marble worktops The screws are not required for granite or marble worktops. ^ Apply silcone to the side edges and the lower edges of spring clamps a and spacer bars b. ^ Then fill gap e between the spacer ^ Position and secure the spring bars and the worktop with silicone.

  • Page 41: Installing The Appliance(s)

    Installing the appliance(s) ^ Feed the connection cable down ^ Starting at the front, position the next through the cut-out. appliance in the worktop cut-out. ^ Starting at the front, position the ^ Connect the appliance(s) to the appliance in the worktop cut-out. mains (see "Electrical connection").

  • Page 42: General Installation Tips

    General installation tips Seal between the appliance and the Tiled worktop worktop Grout lines a and the hatched area The sealing strip under the edge of the top part of the appliance provides a underneath the surface of the sufficient seal for the worktop. appliance must be smooth and even.

  • Page 43: Electrical Connection

    H 05 V V-F be provided for all poles. (pvc insulated), available from Miele. For extra safety it is advisable to protect the appliance with a suitable residual Installation, repairs and other work current device (RCD).

  • Page 44

    Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. It is most important that this basic safety requirement is present and tested regularly and if there is any doubt the electrical wiring in the home should be inspected by a...

  • Page 45: After Sales Service, Data Plate, Guarantee

    Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance which are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.

  • Page 48

    Alteration rights reserved/ 5012 M.-Nr. 09 551 700 / 01...

Comments to this Manuals

Symbols: 0
Latest comments: