Textron GREENSPLEX II 898865 Maintenance Manual
  1. Manuals
  2. Brands
  3. Textron Manuals
  4. Lawn Mower
  5. GREENSPLEX II 898865
  6. Maintenance manual
Textron GREENSPLEX II 898865 Maintenance Manual

Textron GREENSPLEX II 898865 Maintenance Manual

Gasoline greensmower
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PARTS AND
MAINTENANCE MANUAL
GREENSPLEX II
GASOLINE GREENSMOWER
MODEL 898865
Part No. 4115645

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GREENSPLEX II 898865 and is the answer not in the manual?

Questions and answers

Related Manuals for Textron GREENSPLEX II 898865

Summary of Contents for Textron GREENSPLEX II 898865

  • Page 1 PARTS AND MAINTENANCE MANUAL GREENSPLEX II GASOLINE GREENSMOWER MODEL 898865 Part No. 4115645...

  • Page 2: General Information

    All information contained in this manual is the latest death. WARNING indicates unsafe actions or situations available at the time of printing. Textron Golf, Turf and that may cause severe injury, death and/or major equipment or property damage. CAUTION indicates...

  • Page 3: Table Of Contents

    MAINTENANCE SECTION CONTENTS Identification ............Model Number &...
  • Page 4 PARTS SECTION CONTENTS 12.1 Decal Locations ..........12.2 Decals .

  • Page 5: Identification

    IDENTIFICATION 1 IDENTIFICATION THESE IDENTIFICATION NUMBERS MUST APPEAR ON ALL CORRESPONDENCE CONCERNING THIS UNIT. 1.1 MODEL NUMBER & SERIAL NUMBER Both the Model Number and Serial Number are on the identification nameplate decal located above the rear tire (See Fig. 1). Figure 3 1.

  • Page 6: Specifications

    3 SPECIFICATIONS SPECIFICATIONS Dimensions: Width Of Cut ..... . 62 (1.6m) (subject to change without notice) Overall Width (w/reels and catchers) 74.5 (1.9m) Overall Length (w/reels and catchers) 98 (2.5m) Engine...

  • Page 7: Controls

    CONTROLS 4 CONTROLS HAND CONTROLS Ammeter – indicates amount of electrical flow at the battery. Under normal operating conditions the needle will be on the plus (+) side of the meter, showing that current is being supplied to the battery. At idle speed, the indicator may be at zero or on the negative (–) side.

  • Page 8: Control Pedals

    4 CONTROLS CONTROL PEDALS The Direction/Speed Pedal (See Fig. 6) controls speed and direction. Depress front of pedal to go forward, depress back of pedal to go backward. Increased movement of the pedal will increase speed. To slow and stop the unit, release the pedal completely. Proper braking is provided by hydrostatic pressure.

  • Page 9: Adjustments

    ONLY . If assistance is needed, contact 4. After you are properly seated in the operator’s seat, your local Textron Dealer. restart the unit and lower the cutting heads. To avoid the possibility of serious injury, switch the reel enable switch to the “OFF”...

  • Page 10: Bedknife Adjustment

    5 ADJUSTMENTS BEDKNIFE ADJUSTMENT 3. Using a wrench rotate the reel forward. The reel must turn freely and you should just be able to hear NOTE: If the backlap valve accessory (Part No. the reel blades making slight contact with the 2702016) is installed, the backlap valve control bedknife (See Fig.

  • Page 11: Height Of Cut

    ADJUSTMENTS 5 HEIGHT OF CUT Gauge Screw NOTE: All three cutting heads MUST BE accurately set Front Roller Rear Roller Head at the same height of cut to insure an even cut. Bedknife Bedknife adjustment must be made before setting the height of cut.

  • Page 12: Leveling Linkage For The Front Cutting Heads

    5 ADJUSTMENTS LEVELING LINKAGE FOR THE 5.5 MOW/TRANSPORT SPEED CONTROL FRONT CUTTING HEADS When cutting heads are raised completely, the wheel drive speed range is 0 - 7.5 mph (0 - 12 Km/hr). Speed is controlled by use of the direction/speed control pedal as described in control pedals section.

  • Page 13: Setting Bellcrank Stop Screw

    ADJUSTMENTS 5 bellcrank contacts the stop screw. With the screw held tightly against the bellcrank, tighten the stop screw nut. WARNING This procedure MUST BE performed as specified Install the center foot panel. and only by properly trained service personnel. Adjusting the speed control screw out (increasing length) will reduce the mow speed.

  • Page 14: Head Lift & Lower Timing

    5 ADJUSTMENTS HEAD LIFT & LOWER TIMING 2. Once you have completed setting the sequence control switch, move to the limit switches above the rear head (See Fig. 21). Cutting head lift and lower timing are controlled by the 3. With the heads lowered and cylinders fully retracted, sequence control and limit switches.

  • Page 15: Maintenance

    1. Engine must be OFF and cool . When replacement parts are required, use gen- uine Textron parts or parts with equivalent characteristics including type, strength and 2. Turn hydraulic pump lever on bottom of pump 180 material. Failure to do so may result in product...

  • Page 16: Maintenance Guide

    6 MAINTENANCE MAINTENANCE GUIDE The following maintenance chart has been compiled as a general guideline for service intervals, based on hours of operation. 600 Hrs Maintenance Operation Daily Weekly 50 Hrs 250 Hrs Yearly Page Section Check tire pressure 6.16 Check for hydraulic fluid leaks 6.11 Check engine oil level...

  • Page 17: Lube Chart

    MAINTENANCE 6 LUBE CHART Lubricate sparingly with a lithium based lubricant. Excess lubrication may drop from unit and cause turf damage. Always wipe lubrication fittings before and after lubrication. Reel Bearings Rollers (both ends) (both ends) Cutting Head Pivot Cutting Head Pivot Cutting Head Mount Cutting Head Mount Mow/Speed Control Pivot...

  • Page 18: Fuel Recommendations

    6 MAINTENANCE FUEL RECOMMENDATIONS ENGINE ACCESS Fuel tank should be filled to within 1/2 (13mm) below the The rear section of the unit can be raised for better bottom of the filler neck. DO NOT over fill the tank. access to the engine. Loosen the two handknobs above Unleaded gasoline .

  • Page 19: Air Cleaner

    MAINTENANCE 6 AIR CLEANER Vanguard Engines: refer to the engine operator’s manual for air cleaner service and replacement. NOTE: DO NOT use bent or dented air cleaner housing. DO NOT use bent or dented air cleaner elements. IMPORTANT! WE RECOMMEND THAT THE FILTER ELEMENT BE REPLACED BEFORE ENGINE PERFORMANCE IS AFFECTED.

  • Page 20: Hydraulic System

    6 MAINTENANCE 6.11 HYDRAULIC SYSTEM 5. Before disconnecting any hydraulic component, tag or mark the location of each hose then clean the area Reservoir Capacity ....4.8 gal.
  • Page 21 MAINTENANCE 6 Once the hydraulic oil is replaced, the air must be purged All of the above fluids are interchangeable within the from the system. Operate the unit for five minutes to 32/46 multi–viscosity group. stabilize the oil level. Once the air is purged and the oil level is stabilized, fill the Use of the 32/46 multi–viscosity type fluids in the higher tank to its proper level.

  • Page 22: Removal And Installation Of The Rear Fork And Tire

    22 of this (95–140 NSm). manual. 9. Using previously retained hardware, install and A Backlap Valve Kit (Part No. 2702016) is available secure tire and hub assembly to the rear fork. through your Textron dealer.

  • Page 23: Tires

    MAINTENANCE 6 6.17 TIRES NOTE: Keep top of battery clean and free of corrosion by washing with a solution of baking soda and water Keep tires properly inflated to prolong tire life. Check OR ammonia and water. Rinse with clean water. inflation pressure while the tires are cool.

  • Page 24: Accessories

    A Backlap Valve Kit (Part No. 2702016) is available entire length of each blade of the reel. Use a brush through your Textron dealer. with a long enough handle to keep you away from the rotating blades. For best results, use a handle length...

  • Page 25: 3-Wheel Drive

    A 3–Wheel Drive Kit (Part No. 4115585) is available 6. Make certain that the tires are properly inflated. through your Textron dealer. 7. Check to make sure all safety decals are in place and This kit will provide a wheel motor to be installed on the legible.

  • Page 26: Troubleshooting

    9 TROUBLE SHOOTING TROUBLESHOOTING Nothing happens when key is turned (engine won’t crank): Direction/Speed pedal not in neutral ....Pedal should return to neutral automatically, if not, check the neutral centering mechanism and micro switches located below the hydrostat pump Mow or Lift pedal engaged...

  • Page 27: Hydraulic Diagram 10

    HYDRAULIC DIAGRAM 10...

  • Page 28: 11 Torque Chart

    11 TORQUE CHART TORQUE SPECIFICATIONS HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Shank Size (Diameter in inches, fine or coarse thread) Grade 1/4 5/16 3/8 7/16 1/2 9/16...
  • Page 29 NOTES...
  • Page 30 NOTES...
  • Page 31 NOTES...
  • Page 32 12 PARTS SECTION PARTS SECTION...

  • Page 33: Decal Locations

    DECAL LOCATIONS 12.1...

  • Page 34: Decals

    12.2 DECALS CHOKE with GreensCare N O T I C E THIS MACHINE USES TEXTRON GREENSCARE 68, A BIODEGRADABLE HYDRAULIC FLUID. SEE OPERATORS MANUAL FOR APPROVED ALTERNATE FLUIDS. USE OF ALTERNATE FLUIDS WILL COMPROMISE ALL BIODEGRADABLE PROPERTIES OF GREENSCARE HYDRAULIC FLUID.
  • Page 35 ......844847 Decal, TEXTRON ......
  • Page 36 12.3 CHASSIS AND COVERS...
  • Page 37 CHASSIS AND COVERS 12.3 Ref. Part Description Req’d Notes 103867 Washer, 5/16” ....... 4115194.7 Step, foot .

  • Page 38: Power Assembly

    12.4 POWER ASSEMBLY Replacement engine specification: Vanguard, 18hp, V–twin Model 350447, Type 1294 Existing Hardware Service Kit Part No. 547731 is available for Item No. 35 Existing Gasket Obtain Engine Locally Vanguard engine parts available from your Ransomes dealer: 842512 Fuel filter 842514 Spark plug...
  • Page 39 POWER ASSEMBLY 12.4 Ref. Part Description Req’d Notes 120052 Lockwasher, #10 ......120166 Lockwasher, 1/2”...

  • Page 40: Hydraulic Reservoir & Fuel System

    12.5 HYDRAULIC RESERVOIR & FUEL SYSTEM N O T I C E THIS MACHINE USES TEXTRON GREENSCARE 68, A BIODEGRADABLE HYDRAULIC FLUID. SEE OPERATORS MANUAL FOR APPROVED ALTERNATE FLUIDS. USE OF ALTERNATE FLUIDS WILL COMPROMISE ALL BIODEGRADABLE PROPERTIES OF GREENSCARE HYDRAULIC FLUID.
  • Page 41 HYDRAULIC RESERVOIR & FUEL SYSTEM 12.5 Ref. Part Description Req’d Notes 120052 Lockwasher, #10 ......120177 Lockwasher, 3/8”...

  • Page 42: Oil Cooler Mounting

    12.6 OIL COOLER MOUNTING Reference Elbow on Reservoir Reference Tee Union on Lift Valve...
  • Page 43 OIL COOLER MOUNTING 12.6 Ref. Part Description Req’d Notes 103867 Washer, 5/16” ....... 2701694.6 Cover, air intake .

  • Page 44: Head Lift And Pump Control Linkage

    12.7 HEAD LIFT AND PUMP CONTROL LINKAGE...
  • Page 45 HEAD LIFT AND PUMP CONTROL LINKAGE 12.7 Ref. Part Description Notes Req’d 2700942 Shield, Switch ......300646 Screw, 1/4-20 x 3/4”...

  • Page 46: Hydraulic Gear Pump And Reel Control Valve

    12.8 HYDRAULIC GEAR PUMP AND REEL CONTROL VALVE To Lift Valve To Reel Circuit To Reel Circuit Existing Hardware Service Kit Part No. 2702707 is available for Item No. 2 To Hydraulic Reservoir...
  • Page 47 HYDRAULIC GEAR PUMP AND REEL CONTROL VALVE 12.8 Ref. Part Description Req’d Notes 103867 Washer, 5/16” ....... 2701711 Pump, hydraulic gear .

  • Page 48: Hydraulic Lift Circuit

    12.9 HYDRAULIC LIFT CIRCUIT To Reel Control Valve...
  • Page 49 HYDRAULIC LIFT CIRCUIT 12.9 Ref. Part Description Req’d Notes 302754 Screw, 1/4–20 x 2 1/4” ..... . . 306501 Screw, 5/16–18 x 1 1/2” .

  • Page 50: Hydraulic Reel Circuit

    12.10 HYDRAULIC REEL CIRCUIT Service Kit 2702706 Reference Reel Valve Indicates parts are offered only as a set (item no. 28)
  • Page 51 HYDRAULIC REEL CIRCUIT 12.10 Ref. Part Description Req’d Notes 306424 Screw, 5/16-18 x 2 ......308090 Washer 1/4 .

  • Page 52: Reel Case Drain Circuit

    12.11 REEL CASE DRAIN CIRCUIT Reservoir Ref. Part Description Req’d Notes 523764 Adapter, straight ......838565 Tee, O–ring .

  • Page 53: Service "O"Rings Available

    SERVICE “O”RINGS AVAILABLE 12.12 FLAT FACE “O” RINGS SAE PORT “O” RINGS Part Number Tube I.D. AS–568# Part Number Thread Size AS–568# 158061-04 1/4” –011 158061-10 9/16–18 –906 158061-01 3/8” –012 158061-11 3/4–16 –908 158061-02 1/2” –014 158061-12 7/8–14 –910 158061-08 5/8”...

  • Page 54: Hydraulic Wheel Drive Circuit

    12.13 HYDRAULIC WHEEL DRIVE CIRCUIT Service Kit Part No. 891910 is available for Items 30 & 33 Service Kit Part No. 547731 is available for Item No. 34 Reservoir Reservoir...
  • Page 55 HYDRAULIC WHEEL DRIVE CIRCUIT 12.13 Ref. Part Description Req’d Notes 120166 Lockwasher, 1/2” ......158058–01 Fitting, adaptor, 90 .

  • Page 56: Hydraulic Power Steering Circuit

    12.14 HYDRAULIC POWER STEERING CIRCUIT Service Kit 2702705 TANK LEFT PRESSURE RIGHT POWER BEYOND Right side view Service Kit of power steering valve 888378 Ref. Right Front Wheel Motor To hydraulic reservoir Ref. Hydraulic Ref. Lift Pump Solenoid Valve...
  • Page 57 HYDRAULIC POWER STEERING CIRCUIT 12.14 Ref. Part Description Notes Req’d 120166 Lockwasher, 1/2” ....... 2702011 Gear, power steering .

  • Page 58: Control Arm

    12.15 CONTROL ARM Ref. Frame...
  • Page 59 ....839862 Decal, TEXTRON ......

  • Page 60: Lift Assembly – Front Cutting Heads

    12.16 LIFT ASSEMBLY – FRONT CUTTING HEADS Service Kit 894143 REFERENCE FRAME ASSEMBLY...
  • Page 61 LIFT ASSEMBLY – FRONT CUTTING HEADS 12.16 Ref. Part Description Req’d Notes 103960 Washer, 3/4” ID 1 1/2” OD ....2702168 Fitting, lubrication, 1/4-28 .

  • Page 62: Lift Assembly – Rear Cutting Head

    12.17 LIFT ASSEMBLY – REAR CUTTING HEAD Service Kit 891609 Reference on swing arm Reference on frame Reference on frame...
  • Page 63 LIFT ASSEMBLY – REAR CUTTING HEAD 12.17 Ref. Part Description Req’d Notes 103960 Washer, 3/4” ID 1 1/2” OD ....2702168 Fitting, lubrication, 1/4–28 .

  • Page 64: Mow/Raise & Speed Control Pedals

    12.18 MOW/RAISE & SPEED CONTROL PEDALS...
  • Page 65 MOW/RAISE & SPEED CONTROL PEDALS 12.18 Ref. Part Description Req’d Notes 120177 Lockwasher, 3/8” ......302288 Screw, 1/4-20 x 1”...

  • Page 66: Mow Speed Control

    12.19 MOW SPEED CONTROL FRONT UNIT MAIN FRAME SHOWN FOR REFERENCE ONLY...
  • Page 67 MOW SPEED CONTROL 12.19 Ref. Part Description Req’d Notes 2702117 Screw, 3/8-16 x 2” ......306562 Nut, 3/8-16 .

  • Page 68: Brake Pedal

    12.20 BRAKE PEDAL Ref. RH Floor Panel...
  • Page 69 BRAKE PEDAL 12.20 Ref. Part Description Req’d Notes 103867 Washer, 5/16” ......111840 Washer, wavy 1/2”...

  • Page 70: Seat

    12.21 SEAT Reference main frame...
  • Page 71 SEAT 12.21 Ref. Part Description Req’d Notes 103867 Washer, 5/16” ....... 4115594 Panel, seat base .

  • Page 72: Control Panel

    12.22 CONTROL PANEL BLACK BATTERY – TO CHASSIS BLACK INCLUDED WITH ENGINE TO WIRE HARNESS CHASSIS BATTERY + TO SOLENOID SOLENOID TO STARTER...
  • Page 73 CONTROL PANEL 12.22 Ref. Part Description Req’d Notes 120052 Lockwasher, #10 ......158135-01 Switch, seat .

  • Page 74: Electrical Components

    12.23 ELECTRICAL COMPONENTS...
  • Page 75 ELECTRICAL COMPONENTS 12.23 Ref. Part Description Req’d Notes 120052 Lockwasher, #10 ......158135-01 Switch, seat .

  • Page 76: Tires And Rear Hub

    12.24 TIRES AND REAR HUB...
  • Page 77 TIRES AND REAR HUB 12.24 Ref. Part Description Req’d Notes 892225 Hub & Axle, complete ......304104 Nut, jam, 5/8-18 .

  • Page 78: Wheel Drive Accessory

    12.25 3 – WHEEL DRIVE ACCESSORY PART NO. 4115585 UPPER PUMP REF. FRONT RIGHT WHEEL MOTOR REF. CASE DRAIN HOSE...
  • Page 79 3 – WHEEL DRIVE ACCESSORY PART NO. 4115585 12.25 Ref. Part Description Req’d Notes 120166 Lockwasher, 1/2” ......131981 Screw, 1/2–13 x 2 1/2”...

  • Page 80: Cutting Heads

    12.26 CUTTING HEADS CUTTING HEAD ACCESSORIES PART NO. 067135 11 BLADE LH PART NO. 067136 9 BLADE LH (SHOWN) PART NO. 067137 7 BLADE LH...
  • Page 81 CUTTING HEADS 12.26 Ref. Part Description Req’d Notes 5002577 Frame, reel ....... . . 361877 Decal, danger .

  • Page 82: Rear Rollers

    12.27 REAR ROLLERS USED ON CUTTING HEAD ACCESSORIES PART NO. 067135 11 BLADE LH PART NO. 067136 9 BLADE LH (SHOWN) PART NO. 067137 7 BLADE LH...
  • Page 83 REAR ROLLERS 12.27 Ref. Part Description Req’d Notes 1002224 Zerk bolt ........7 Blade reels only 3005692 Knob, front roller adjusting...

  • Page 84: Vertical Mower

    12.28 VERTICAL MOWER PRODUCT NO. 067138 SHOWN FOR REFERENCE ONLY...
  • Page 85 PRODUCT NO. 067138 VERTICAL MOWER 12.28 Ref. Part Description Req’d Notes 5002577 Frame, reel ....... . . 361877 Decal, danger .

  • Page 86: Rollers And Scrapers For Vertical Mower

    12.29 ROLLERS AND SCRAPERS FOR VERTICAL MOWER USED ON VERTICAL MOWER PRODUCT NO. 067138...
  • Page 87 ROLLERS AND SCRAPERS FOR VERTICAL MOWER 12.29 Ref. Part Description Req’d Notes 162916 Roller, rear ....... . . 5002814 Tube, roller .

  • Page 88: Rotary Rear Brush

    12.30 ROTARY REAR BRUSH PRODUCT NO. 068643 USE WITH 5/8” DIA. REEL SHAFT ROTARY REAR BRUSH CAN BE n USE WITH 1/2” DIA. REEL SHAFT USED ON THE FOLLOWING L USE WITH TURF GROOMER CUTTING HEADS: B USE WITH HEAVY DUTY REAR ROLLER PART NO.
  • Page 89 ROTARY REAR BRUSH PRODUCT NO. 068643 12.30 Ref. Part Description Req’d Notes 3007975 Bracket, bearing housing ..... 471514 Fitting, grease, 1/4–28 .

  • Page 90: Rollers, Grooved

    12.31 FRONT ROLLERS PRODUCT NO. 068613 – 2 GROOVED (STEEL) PRODUCT NO. 068614 – 2 GROOVED (ALUMINUM) ROLLER CAN BE USED ON THE FOLLOWING CUTTING HEADS PART NO. 067135 11 BLADE LH PART NO. 067136 9 BLADE LH PART NO. 067137 7 BLADE LH Ref.
  • Page 91 FRONT ROLLERS 12.32 PRODUCT NO. 068530 – 2” SMOOTH W/SCRAPER ROLLER CAN BE USED ON THE FOLLOWING CUTTING HEADS PART NO. 067135 11 BLADE LH PART NO. 067136 9 BLADE LH PART NO. 067137 7 BLADE LH FRONT UNIT ROLLER MOUNTING BRACKET CUTTING HEAD FRAME...

  • Page 92: Turf Groomer

    12.33 TURF GROOMER ACCESSORY PRODUCT NO. 067871, 1/4” SPACING PRODUCT NO. 067873, 1/2” SPACING RIGHT SIDE GROOMER IS SHOWN, LEFT SIDE GROOMER IS THE OPPOSITE...
  • Page 93 TURF GROOMER ACCESSORY 12.33 Ref. Part Description Req’d Notes 365226 Plate, cover ....... . 132212 Pulley assembly .
  • Page 94 12.33 TURF GROOMER DRIVE ASSEMBLY RIGHT SIDE GROOMER IS SHOWN, LEFT SIDE GROOMER IS THE OPPOSITE...
  • Page 95 TURF GROOMER DRIVE ASSEMBLY 12.33 Ref. Part Description Req’d Notes 3010708 Bracket, groomer roller ..... . . 220302 Housing, belt .
  • Page 96 12.33 TURF GROOMER DRIVEN ASSEMBLY RIGHT SIDE GROOMER IS SHOWN, LEFT SIDE GROOMER IS THE OPPOSITE...
  • Page 97 TURF GROOMER DRIVEN ASSEMBLY 12.33 Ref. Part Description Req’d Notes 3010708 Bracket, groomer roller ..... . . 338748 Bracket, groomer mounting .
  • Page 98 12.33 TURF GROOMER BLADE ASSEMBLY RIGHT SIDE GROOMER IS SHOWN, LEFT SIDE GROOMER IS THE OPPOSITE...
  • Page 99 TURF GROOMER BLADE ASSEMBLY 12.33 Ref. Part Description Notes Req’d 367029 Locknut, 3/4–16, hex nyloc ....367165 Spacer, 7/8 x 17/32” ......471214 Fitting, grease, 1/4–28 .
  • Page 100 12.33 TURF GROOMER ROLLER ASSEMBLY Ref. Part Description Req’d Notes 390899 Tube, roller, 1/4” spacing ..... Product No. 067871 390900 Tube, roller, 1/2”...
  • Page 101 TURF GROOMER QUICK HEIGHT ADJUSTER 12.33 Ref. Part Description Req’d Notes 422502 Screw, set, 1/4–20 x 1/4” ..... 365265 Link, adjusting .
  • Page 102 DUAL HEADLIGHT PART NO. 2702015 12.34 REF. CONTROL PANEL Ref. Part Description Notes Req’d 843990 Switch, rocker ......844551 Spacer, switch .

  • Page 103: Tool Box Accessory

    12.35 TOOL BOX ACCESSORY PART NO. 4115589 EXISTING HARDWARE REF. LINE COVER PANEL Ref. Part Description Notes Req’d 306325 Lockwasher, 5/16” ......306375 Nut, 1/4-20 .
  • Page 104 BACKLAPPING ACCESSORY PART NO. 2702016 12.36 Ref. Part Description Req’d Notes 178079 Fitting, test ....... . . 2208047 Valve, 4 way 3 position .

  • Page 105: Roller Spiker Adapter

    12.37 ROLLER SPIKER ADAPTER KIT PART NO. 2702018 Ref. Part Description Req’d Notes 2701485.7 Ballast, spiker ......2701486.7 Bracket, spiker motor .

  • Page 106: Reel Motor Mounting

    REEL MOTOR MOUNTING 12.38 ONLY USED ON CUTTING HEAD ACCESSORIES PRODUCT NO. 067135 11 BLADE LH PRODUCT NO. 067136 9 BLADE LH (SHOWN) PRODUCT NO. 067137 7 BLADE LH PRODUCT NO. 067138 VERTICAL MOWER SHOWN FOR REFERENCE ONLY CUTTING HEAD SHOWN FOR REFERENCE ONLY Ref.

  • Page 107: Wiring Diagrams

    WIRING DIAGRAMS...
  • Page 108 12.39 WIRING SCHEMATIC GREENPLEX II GAS MODELS 20 AMP IGN. SWITCH NOT RECOMMENDED 20 AMP 20 AMP BACKLAP SEAT SWITCH SWITCH HEADLIGHTS SWITCH NEUTRAL SWITCHES PEDAL OIL LEAK SWITCH BUZZER (RAISE) CARBURETOR SOLENOID REAR REAR DOWN MODULE OIL LEVEL LIMIT LIMIT PRESSURE HOUR...
  • Page 109 WIRING SCHEMATIC 12.39 GREENPLEX II GAS MODELS IGNITION OFF HEADS RAISED OPERATOR SEATED HST PEDAL IN NEUTRAL IGNITION OFF REEL ENABLE OFF 20 AMP AMMETER UP LIMIT SEQUENCE STARTER SWITCH RELAY DOWN LIMIT RECTIFIER SEQUENCE RELAY IGNITION ALTERNATOR RELAY REEL ARMATURES SOLENOID STARTER...

  • Page 110: Wiring Diagram

    12.40 WIRING DIAGRAM 898865 RECOMMENDED NOTE: PART NUMBERS SHOWN FOR REFERENCE ONLY. DOWN LIMIT LIMIT SWITCH SWITCH 894520 894520 BUZZER AMMETER WIRE CONNECTIONS WHITE/RED ”S” TERMINAL BLACK ”G” TERMINAL ”I” TERMINAL HOLDER, MODULE HEADLIGHT LAMP AMMETER SWITCH 888502 833280 843990 REEL ENABLE FUSE BLOCK PART OF...
  • Page 111 WIRING DIAGRAM 12.40 898865 TRACKTION NEUTRAL 833615 OIL TEMP. SENDER SWITCHES PART OF ACCESSORY 894485 894385 RECOMMENDED ENGINE WIRE FUNCTIONS OIL LEVEL SENDER WHITE CARBURETOR SOLENOID PART OF ACCESSORY 894485 WHITE/RED ALTERNATOR ORANGE ARMATURES WHITE/ORANGE OIL PRESSURE SWITCH STARTER SOLENOID ENGINE SEQUENCE PRIMARY LUG...

  • Page 112: Maintenance Section Index

    MAINTENANCE SECTION INDEX Hydraulic Pump Bypass Valve ..ccessories ..... Backlap Valve ....Hydraulic System .

  • Page 113: Part Section Index

    PART SECTION INDEX Hydraulic Pump Control Linkage ..ccessories ....76–104 Hydraulic Reel Circuit ....3–Wheel Drive .

  • Page 114: Part Number Index

    PART NUMBER INDEX Page 2208047 ..2702424 ..351521 ... 351522 ... 067135 .
  • Page 115 Page 523253 ... 838026 ... 841487 ... 841522 ... 4115224.7 .
  • Page 116 Page 844075 ..45, 53 889843 ... 894240 ... 843823 ... 844076 .
  • Page 117 SERVICE DATE SERVICE DONE INITIAL...
  • Page 118 SERVICE DATE SERVICE DONE INITIAL...

Table of Contents