The contactless smart card coupler emits radio-frequency waves and must be used as installed and recommended by ANA-U. You may not modify the coupler or how it is used without the written permission of ANA-U. You may not operate the printer after modifying the coupler or its method of operation.
EasyPrinter S3 Programmers Manual Contents Command description..........4 Printer short state..............4 Start printing .................4 Firmwareversion..............4 Read printer state..............5 Read direction detection values ..........5 Read RFID card number............5 Reset printer ................5 Select small font ..............6 Select medium font ..............6 Select big font ................6 Rotate card by 180 degrees .............6...
Page 5
EasyPrinter S3 Programmers Manual Read library number..............13 Read extended number............13 Read SSC number..............13 Read SC number..............14 Set Baudrate.................14 Get cleaning counter .............14 Get printer counter ...............14 Get printhead counter ............14 Set card collector mode............15 Set card material mode ............15 Get card material mode ............15 Set print area................15...
EasyPrinter S3 Programmers Manual Command description Based on Firmwareversion "EP000226". Printer short state Returns the status of the printer (bit coded info) Command: [SUB] Returns: [c] ... bit coded status info (1 byte) Bit 0 ... Card sensor printposition Bit 1 ... Card sensor front Bit 2 ...
EasyPrinter S3 Programmers Manual Read printer state Reads the printer state Command: [ESC] ? Returns: 9 ASCII characters representing the printers state in 8 ASCII boolean format . The return value is terminated with a [CR]. '0'... false '1' ... true...
EasyPrinter S3 Programmers Manual Select small font Command: [ESC] C Select medium font Command: [ESC] D Select big font Command: [ESC] E Rotate card by 180 degrees Command: [ESC] U Rotate card by 0 degrees Command: [ESC] T Print text portrait...
EasyPrinter S3 Programmers Manual Print character in double width Command: [ESC] b [x] [x] ... ASCII-character '0'... false '1' ... true Feed card The printer feeds a card from the card tray Command: [ESC] c Enable printer Forces the printer to insert a card from the front...
EasyPrinter S3 Programmers Manual Set x-Position Set position in card printing direction. (CXone compatible) Command: [ESC] x [xx] [xx] ... ASCII-characters coding print position in x-direction. (Valuerange: 00 - 48 ) Set print area Set the active print area (CXone compatible).
EasyPrinter S3 Programmers Manual Get permanent erase area mode Command: [ESC] L3000000000000 Returns: 13 ASCII characters: [n] ..Activation of the permanent erase area in ASCII char ('1' = active > erase part of the card ; '0' = inactive > erase the whole card) [xx] ..
EasyPrinter S3 Programmers Manual Start Loader Starts the flash loader to update the programm file. For detailed information on firmwareloading, please refer to "ANA-U Firmwareloader Manual". Command: [ESC] ><1 Set erase area Sets the areas where the printer erases the information on the card (CXone compatible).
EasyPrinter S3 Programmers Manual Reboot Software printer restart Command: [ESC] $R Get printenergy-offset (permanent) Returns the actual used printenergy-offset. Command: [ESC] $op Returns: The actual used printenergy-offset in ASCII characters ending with [CR]. Get eraseenergy-offset (permanent) Returns the actual used eraseenergy-offset...
EasyPrinter S3 Programmers Manual Set printenergy-offset (permanent) Set the printenergy-offset to adapt the printer to other materials. This value is store permanent, and is restored after reset and power down. Command: [ESC] $Op [c] [xxx] [c] ... ASCII-characters coding the sign. '+' or '-' [xxx] ...
EasyPrinter S3 Programmers Manual Read cardnumber Read RFID cardnumber. Command: [ESC] $§ N Returns: The cardnumber 12 Byte ASCII alphanumeric with trailing zeros. Read library number Read library number. Command: [ESC] $§ B Returns: The library number 12 byte ASCII alphanumeric with trailing zeros.
EasyPrinter S3 Programmers Manual Read SC number Read SC number. Command: [ESC] $§ K Returns: The SC number 10 byte ASCII alphanumeric with trailing zeros. Set Baudrate Set the baudrate for the host serial interface Command: [ESC] %B [c] [c] ... ASCII-characters '0' to '9' '0' ...
EasyPrinter S3 Programmers Manual Set card collector mode Set if card is dropped or stacked. Command: [ESC] %K [x] [x] ... ASCII-character '0' ... card is dropped '1' ... card is stacked Set card material mode Preconfigures the print-/erase system for the selected TRW-material.
EasyPrinter S3 Programmers Manual Set y-position Set position in card printing direction. Command: [ESC] %y [xxxx] [xxxx] ... ASCII-characters coding print position in y-direction. (Valuerange: 000 - 1150 ) Set x-position Set position in card printing direction. Command: [ESC] %x [xx] [xx] ...
EasyPrinter S3 Programmers Manual Get PrinterDefinitionBitsExt Read the hardware definition. Command: [ESC] %ol Returns: 1 Byte with the actual setup. Bit 0 ... Check for card in frontslot without being enabled Bit 1 ... Not used! Bit 2 ... Not used! Bit 3 ...
EasyPrinter S3 Programmers Manual Get printhead type Command: [ESC] %OD Returns: Always returns '3' for 300 dpi printhead. Set printers IP address Command: [ESC] %OI [cccc] [cccc] ... 4 Byte defining the IP address of the printer. Set printers subnetmask...
EasyPrinter S3 Programmers Manual Contact ANA-U GmbH Moosgrabenstrasse 32 8200 Gleisdorf, AUSTRIA E-Mail Support: info@ana-u.com Website: http://www.ana-u.com Spare part and Support Hotline: +43 3112 368 41 Page 22 of 23 Version 1.3 - 19. April 2012...
Page 25
The content of these instructions is not allowed to be duplicated, processed or translated in any form, either in its entirety or extracts thereof, without the written approval of the company ANA-U GmbH. All technical specifications, drawings, etc. are subject to the law relating to the protection of copyright. The manufacturer of the product reserves the right to make changes without previous notice.