Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation
and Operating Instructions supplied with the fireplace
and should be kept together. Refer to the Installation
and Operating Instructions for proper gas supply, safety
requirements and operating instructions
230415-20
TC36 See-Thru
BLACK DIAMOND
BURNER KIT
PART#
FOR TC36 SEE-THRU
SERIES D FIREPLACES
TC36ST_NGST03D
TC36ST.NGST03D
5056.42801D3
Advertisement
Table of Contents
Related Manuals for Town & Country Fireplaces TC36 TC36ST.NGST03D
Summary of Contents for Town & Country Fireplaces TC36 TC36ST.NGST03D
- Page 1 INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the fireplace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions TC36 See-Thru BLACK DIAMOND...
-
Page 2: Package Contents
Package Contents 1 BURNER TUBE ....................TC36.50118398 1 SHUTTER CONTROL ROD ..................5002.1752 1 BURNER TRAY ASSEMBLY ................... TC36.9690 2 BURNER SHIELD, FRONT/REAR ..............TC36.9693PBK 1 LEFT BURNER SHIELD ................TC36.9693.2PBK 1 RIGHT BURNER SHIELD ................TC36.9693.5PBK 1 LINE COVER ....................TC36.9699PBKA 1 PILOT SHIELD ....................TC36.9626PBK 1 MANIFOLD ASSEMBLY .................. - Page 3 Black Diamond Burner Installation Fig. # 2 NOTE: For the purposes of these instructions the controls and gas connections are on the right hand side of the unit. Remove porcelain panels if they are installed. Remove the panel retainer clip located on the upper heat shield, install the left panel securing with panel retainer clip previously...
- Page 4 2 SCREWS 4. Secure the electrical bulkhead Fig. # 4 plate (Fig.#4) and gasket to the firebox. (2 screws) Attach the ignition and sensor wires to the module. (Fig.#5). BULKHEAD PLATE NOTE: If converting to propane refer to the propane conversion section before continuing.
- Page 5 Fig. # 6 5. Attach the inlet cover using the top screw of the bulkhead (Fig. #6). Install the right porcelain panel (as in Fig. #2). Fig. # 7 6. Position the right burner shield over the inlet cover ensuring that the pilot assembly is protruding through the half-hole between the inlet cover and...
- Page 6 Fig. # 8 While supporting the right burner shield install the rear burner shield, resting the edge of the right burner shield onto the support tab of the rear burner shield (Fig. #8). Fig. # 9 8. Install the front burner shield positioning the support tab under the right burner shield (Fig.
- Page 7 9. Install the left burner shield. This Fig. # 10 will be a snug fit requiring some alignment (Fig. #10). Fig. # 11 10. Position the burner tray assembly on top of the assembled shields and attach it using four screws (Fig.
- Page 8 Fig. # 12 11. Attach the pilot assembly to burner tray using two screws (Fig. #12). Fig. # 13 12. Position a front/rear media spacer at the rear of the burner tray (Fig. #13). TC36ST_NGST03D_230415-20...
- Page 9 Fig. # 14 13. Position the other at the front of the tray (Fig. #14). 14. Loosen the screw on the burner tube shutter enough Fig. # 15 to allow smooth movement from open to closed positions (visible in Fig. #16). 15.
- Page 10 6. Hold the burner tube in a position Fig. # 16 so that the shutter control rod can be inserted into the shutter tab (Fig. #16) after passing through the rod hole in the top right corner of the front burner shield. (See Fig.
- Page 11 Fig. # 18 19. Empty the contents of the supplied tumbled glass bag onto the burner tray (Fig. #18) and spread the glass evenly over top of the tube and media spacers (Fig. #19). NOTE: Too much tumbled glass over the burner will cause sooting.
-
Page 12: Propane Conversion
Propane Conversion This kit for use with model: / TC36STNG03.D Pour utilise avec du modèle: / TC36STNG04.D TC42 Date: ______________________ WARNING Series D By / Par: ___________________ This conversion kit LP GAS/ This appliance was converted shall be installed by a DU GAZ LP to PROPANE GAS with this kit on this date by the... - Page 13 Slide the pilot adjustment band Fig #23 over and ensure that the hole in t h e o r i f i c e b a n d i s s h o w i n g. (Fig. #23 indicates NG position, Fig.
-
Page 14: Gas Pressure Check
ADD DATE ADD NAME 12) Fill in the date and the name of the person who performed the conversion This kit for use with model: / TC36STNG03.D in the white area on the conversion Pour utilise avec du modèle: / TC36STNG04.D label. -
Page 15: Burner Flame Adjustment
Burner Flame Adjustment The air shutter on the burner tube controls the primary combustion air. It is set to the closed position at the factory for natural gas fuel. Some adjustment may be Fig #27 necessary to obtain desired flame and to eliminate carbon deposits. -
Page 16: Replacement Parts
Replacement Parts NOTE: FIREPLACE & VALVE REPLACEMENT PARTS ARE LOCATED IN THE APPLIANCE INSTRUCTIONS ITEM ... DESCRIPTION ......PART NO. 1..MEDIA SPACER, CENTER ....9694 2..BURNER TUBE ....TC36.50118398 3..MEDIA SPACER, FRONT/REAR ...9695 4..TRAY TRIM .........9690.5 5..PILOT ASSEMBLY ....TCRP.5005025 6.. - Page 17 TC36ST_NGST03D_230416-20...
- Page 18 Minimum rate screw TC36ST_NGST03D_230415-20...
- Page 19 TC36ST_NGST03D_230416-20...
- Page 20 © 2015 Copyright Pacific Energy Fireplace Products LTD Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. For technical support, please contact your retailer. www.townandcountryfireplaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...
Need help?
Do you have a question about the TC36 TC36ST.NGST03D and is the answer not in the manual?
Questions and answers