Electronic Oven Controls; Control Display; Tones; Energy Save - Whirlpool Gas Range User Manual

KEYPAD
AOUALIFT
SELF CLEAN
START
(hold 3 sec
to lock)
ENERGY
SAVE
FEATURE INSTRUCTIONS
Clean cycle See the "Clean Cycle" section.
Oven control
lockout
Puts the range
into sleep mode
to reduce energy
usage
1. Check that the oven is off.
2. Press and hold START (hold 3 sec to lock) for 3 seconds.
3. A tone will sound, and "Control Locked" will scroll, then "Locked" will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked. The cooktop functions
are not affected by the oven control lockout.
1. Press and hold SETTINGS/CLOCK for 3 seconds to change status. The display will scroll
"Energy saver on" or "Energy saver off."
If Energy Save is on, the range will go into sleep mode after 5 minutes of inactivity. Any key
press will activate the display. If Energy Save is off, the display will be on at all times.
IIE)eot oHio Oven OoHt o)s
Control Display
The display will flash when powered up or after a power loss. Press
CANCEL to clear. When the oven is not in use, the time of day is
displayed. If the range is in Energy Save mode, the display will be
blank when not in use.
Tones
Tones are audible signals, indicating the following:
One tone
• Valid pad press
• Oven is preheated (long tone)
• Function has been entered
• Reminder, repeating each minute after the end-of-cycle tones
Three tones
• Invalid pad press
Four tones
• End of cycle
Use the Settings/Clock key to change the tone settings.
Energy Save
The Energy Save mode puts the range into sleep mode and
reduces energy consumption.
To Activate the Energy Save Mode:
1. Press and hold SETTINGS/CLOCK for 3 seconds. "Energy
saver on." will appear in the display.
2. The setting will be activated after 5 minutes.
To Deactivate the Energy Save Mode:
1. Press and hold SETTINGS/CLOCK for 3 seconds. "Energy
saver off." will appear in the display.
2. The clock will reappear in the display, and the range can be
operated as usual.
Settings
Many features of the oven control can be adjusted to meet your
personal needs. These changes are made using the Settings/
Clock key.
Use the Settings/Clock key to scroll through the features that can
be changed. Each press of the Settings/Clock key will advance the
display to the next setting. After selecting the feature to be
changed, the control will prompt you for the required input. After
the setting is saved by pressing Start, press CANCEL to exit
Settings and display the time of day. Details of all of the feature
changes are explained in the following sections.
Press CANCEL to exit Settings.
Clock
The Clock can use a 12- or 24-hour cycle.
1. Press SETTINGS/CLOCK until "CLOCK" is displayed.
2. Press START to change the time.
3. Press "3" for AM or "6" for PM.
4. Use the number keypad to set the time of day.
5. Press SETTINGS/CLOCK or START to save the setting.
6. Press CANCEL to exit and display the time of day.
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
1. Press SETTINGS/CLOCK until "TEMP UNIT" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press START or CANCEL to exit and display the time of day.
Audible Tones Disable
Turns off all tones, including the end of cycle tone and key press
tones. Reminder tones are still active when all tones are disabled.
1. Press SETTINGS/CLOCK until "SOUND" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press START or CANCEL to exit and display the time of day.
Sound Volume
Sets the pitch of the tone to either high or low.
1. Press SETTINGS/CLOCK until "SOUND VOLUME" is
displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press START or CANCEL to exit and display the time of day.
End of Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
1. Press SETTINGS/CLOCK until "END TONE" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press START or CANCEL to exit and display the time of day.