Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HDL BusPro SB-CMS-12in1
Summary of Contents for HDL BusPro SB-CMS-12in1
-
Page 1: User Manual
User manual Multi function Sensor SB-CMS-12 in1 www.hdlautomation.com... -
Page 2: Table Of Contents
2. Safety Instructions ......................3 3. Technical Data ....................... 3 4. Installation ........................4 4.1 Wiring ........................4 4.2 HDL Bus Pro Description ..................4 4.3 Commissioning ....................5 5. Software Configuration ....................5 5.1 Basic setting ......................5 5.1.1 Change the ID of the device ..............5 5.1.2 LED Indicators Settings ................ -
Page 3: Overview
12in1sensor includes temperature sensor, PIR motion sensor, LUX sensor, ultrasonic sensor, dry contacts, IR received, IR emitter, 2CH 5A relay output and logic block. The logic block can combine all sensors for different applications. It supports HDL security function. 1.1.2 Mounting... -
Page 4: Functionnalities Description
Up to 240 IR sending control targets Maximum 24 programmable logic blocks Security function, work with the security module Supports upgrade from HDL BUS 1.3 Device Description ○ ○ ○ a . Programming button ○ ○... -
Page 5: Safety Instructions
User Manual SB-CMS-12in1 2. Safety Instructions Screw down strength is less than 0.1Nm. Do not make wrong connection on Bus interface, it will damage the Bus interface of thismodule. Do not get AC power into Bus wire, it will damage all devices in the system. ... -
Page 6: Installation
Dimensions 110(Diameter)×33(mm) Weight 206.7(g) Housing material Lens, ABS Installation Ceiling mount Protection degree IP20 4. Installation 4.1 Wiring HDL Buspro 4.2 HDL Bus Pro Description Connector Information buspro DC24V Black DATA - White DATA + Yellow Multi function Sensor–User Manual... -
Page 7: Commissioning
5.1 Basic setting 5.1.1 Change the ID of the device Every HDL-BUS device has one Subnet ID and one Device ID, the Device ID should be unique in its subnet and the Subnet ID should be kept consistent with the Gateway (typically the SB-DN-1IP or HDL-MBUS01IP.431). -
Page 8: Led Indicators Settings
You need an IR learnerto learn and upload the IR codes of your normal remote to the 12in1, also there are some codes have been stored in the HDL BUS setup tool, can view them in „All IR Codes‟ window. -
Page 9: Ir Receiver
5.3 IR Receiver Can send UV switch 249 „ON‟ command to enable the IR Receiver, or „OFF‟ to disable from panel or other devices. Generally it works with HDL‟s IR/RFRemote Controller (HDL-MTIRW), which has built-in HDL self-defined IR codes, can control HDL panels/sensors directly, no need to learn IR codes.12in1 can support up to 5 pages, 40... -
Page 10: Sensors Setting
User Manual SB-CMS-12in1 5.4 Sensors setting 5.4.1 Basic Info - Remarks of dry contacts Remarks are recommended, you may make remarks according to the installation places - On-Site Status You can check the real-time values of sensors by refreshing or enable „Update status automatic‟... -
Page 11: Constant Lux Function
- Ki The smaller the factor is, the more accurate final output it can provide. 5.4.3 Adjust Lux Sensor It‟s adjusted by HDL, normally not recommended to adjust again unless it‟s quite incorrect. Password：85521566 5.5 Logic Relation You can set up to 24 logics and in each logic you can combine up to 9 inputs (conditions), trigger up to 20 targets when the logic is true and another 20 targets when false. -
Page 12: Logic Information
User Manual SB-CMS-12in1 5.5.1 Logic Information - Power On Delay（0-120s) This parameter is specially designed for „Power OFF Recovery‟ (if you select „true‟ in the „Power OFF Recovery‟, you may get jam on the bus when initializing. you can set „Power On Delay‟... -
Page 13: Further Settings Of Current Logic
User Manual SB-CMS-12in1 - On-Site Status Show the value detected by sensors 5.5.2 Further Settings of Current Logic There are 9 conditions, select the conditions you need. The details are as follows. -Temperature（° C） Condition is satisfied when the temperature is in the range you set. Setting Range：－20°... -
Page 14: Relation
User Manual SB-CMS-12in1 -Logic You can take the status (true of false) of other logic as a condition.（can‟t be the logic of itself） 5.5.3 Relation If more than one conditions are selected, you can set the logic relationship between them as „AND‟... -
Page 15: Application
User Manual SB-CMS-12in1 5.5.5 Application - Application1 Turn on light when detects movement, and turn it off when no movement after 10s. a) Enable logic No.1, set IR Sensor - Movement as the condition b) Logic true delay is 0s, in „trigger target when true‟ window, input dimmer/relay ID, here is 1-6, parameter 1 is channel 2, parameter 2 is 100. - Page 16 User Manual SB-CMS-12in1 b) After 1 minute turn on the AC and set the temperature as 25℃: Set IR Sensor - „Movement‟ and dry contact1 - „Connect‟ as input conditions, and the relation for the logic is „AND‟, delay time is 1 min, turn on AC when true. Can check the UV Switch No.
- Page 17 User Manual SB-CMS-12in1 Can check the UV Switch No. from IR Emitter, here 27℃is UV Switch 5. d) 3 minutes after people left the room, turn off the AC automatically Set IR Sensor - „ No Movement‟, delay time is 3 min, turn off AC when true. Can check the UV Switch No.
-
Page 18: Security Function
User Manual SB-CMS-12in1 5.6 Security function The states (connected/disconnected) of dry contacts, states (movement/no-movement) of IR sensor and states (present/absence) of ultrasonic sensor can be set as triggers to security module. If use dry contact 1 to detect the door state for security, the setting steps as follow: a) Select „dry contact 1‟... -
Page 19: Normalmode
User Manual SB-CMS-12in1 5.7.1 Normal Mode - Open Delay ON delay, setting range: 0-25.0s. - Protection Delay e.g. Set protection delay as 1 min(open delay as 0), now turn off relay, after 25s, you want to turn on it, it will not turn on until 35s later; setting range: 0-60min. 5.7.2 Cycle Mode If you enable the cycle mode and set it on, it will automatically produce an “on-off-on-off”... -
Page 20: Simulate Test
User Manual SB-CMS-12in1 5.8 Simulate Test You can simulate the logic you have set up by giving the sensors values or status. (When in simulate state, the real-time values will be bypassed and replaced by values you have given to them) Multi function Sensor–User Manual... - Page 21 User Manual SB-CMS-12in1 6. Note ………………………………………………………………………………………………………. ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… ……………………………………………………………………………………………………… Multi function Sensor–User Manual...