Related Manuals for Strong SRT 8102+
Summary of Contents for Strong SRT 8102+
- Page 1 Digital High Definition Terrestrial Receiver SRT 8102+ User manual Manuel d’Utilisateur Manuale Utente Manual del usuario Manual do Usuário Felhasználói kézikönyv Instrukcja obsługi Руководство пользователя...
-
Page 4: Table Of Contents
8.0 TRoublEshooTIng 9.0 TEChnICAl sPECIfICATIons sTRong declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, Rohs 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. -
Page 5: Introduction
PART 1 • English 1.0 InTRoduCTIon 1.1 safety Instructions do noT InsTAll YouR RECEIvER: In a closed or poorly ventilated cabinet; directly on top of or under any other „ „ equipment; on a surface which might obstruct the ventilation slots. do noT EXPosE ThE RECEIvER oR ITs ACCEssoRIEs: To direct sunlight or any other equipment that generates heat;... -
Page 6: Equipment Set-Up
„ „ the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information. 2.0 YouR RECEIvER 2.1 PIn-CodE dEfAulT: 0000... -
Page 7: Rear Panel
PART 1 • English 3. mode indicator: REd indicates that the receiver is in STANDBY mode. gREEn indicates that the receiver is in OPERATING mode. 2.3 Rear Panel Fig. 2 1. AnT In To connect to your antenna for the reception of broadcast signal. 2. -
Page 8: Connection
For proper functioning of Time Shift and recording functions, a fast USB device (such as a hard disk drive) is needed. Interrupted playback or a distorted picture during playback or Time Shift are indications for a low device speed. STRONG cannot guarantee proper functioning of recoding and or Time Shift functions with all USB devices. -
Page 9: Starting Up For The First Time
PART 1 • English 4.0 sTARTIng uP foR ThE fIRsT TImE If you use your receiver for the first time, the Welcome “Easy install” menu appears. Use pq to move the highlight to the setting you wish to alter and use tu to change values. Start by selecting your language using tu. -
Page 10: Quick Guide To Using Your Receiver
5.0 QuICk guIdE To usIng YouR RECEIvER We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your receiver. -
Page 11: Info Banner
PART 1 • English 6.2 Info banner While watching TV you can press the Info button any time to get information about the current channel and event*. Press Info twice for extended EPG details about the current channel. Press Info three times for technical details about the current channel. *Event information is displayed when available. -
Page 12: Instant Recording
PART 1 • English 6.8 Instant Recording Your new receiver allows you to make an instant recording of the programme you are watching. Simply press RECoRd to start the recording. To enter the duration for the recording, press RECoRd again. Use the 0~9 keys to input the desired recording time. During the start of recording a recording sign will be shortly shown on the upper left of your TV screen. -
Page 13: Skipping Channels
PART 1 • English Select Yes to save the changes or No to discard. Locking/unlocking multiple channels in one session is possible. 7.1.1.3 skipping channels Channels marked with Skip will be skipped when zapping channels with the pq buttons. The channels will still be available from the channel list. -
Page 14: Installation
PART 1 • English delete Press bluE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected. Use pq to highlight a channel and press ok to mark it for deletion. The receiver asks you to enter the pin code. -
Page 15: System Setup
PART 1 • English The following settings are available: Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will be present on the ANT IN connector of the receiver. Select Off for passive antennas. Beeper: Select On for an audible indication of signal reception. -
Page 16: Local Time Setting
PART 1 • English Connection: Use this option to select the connection to your TV set. Select HDMI or TV SCART. If connection type HDMI is selected, then only the CVBS signal is available on the TV SCART. Digital Audio Output: Toggles between PCM and Bitstream output. -
Page 17: Tools
This submenu shows receiver specific information such as hardware version and software version. It also displays our web address www.strong.tv. Please have the Receiver Information screen on hand when you call our hotline. The person who answers your call might ask for the information given in... -
Page 18: Load Factory Setting
This receiver is equipped with an Over The Air software upgrade option. An Over The Air update might not be available in your region. Please visit our website www.strong.tv or contact your local service hotline for more information about this option. -
Page 19: Games
PART 1 • English After performing this function, the USB device is no longer accessible from noTE: your receiver. To gain access to your storage device again, re insert it or switch the receiver to standby and on again. 7.5 games Your receiver is equipped with two games which can be played on your TV screen using the receiver remote control. -
Page 20: Dvr Hdd Information
Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver. -
Page 21: Troubleshooting
Replace remote batteries Forgotten PIN code Default PIN is 0000 Contact local Service Hotline or send email to our Support via www.strong.tv After moving the receiver Antenna signals are too weak Press the INFO button on to another room/area you... -
Page 22: Technical Specifications
MP3 and OGG** Picture view BMP and JPEG format** **STRONG cannot guarantee the playback of video files although extensions are listed, as it depends on codec used, data bit rate and resolution (all MPEG codec formats are supported). Connectors ANT IN - IEC Female TO TV - IEC Male TV SCART (RGB, CVBS, Audio L&R) - Page 23 PART 1 • English general data Supply Voltage: 220 – 240 V AC (SMPS), 50/60 Hz Power Consumption: 5.5 W (typ.), 12.00 W (max) Power consumption in Standby: 0.85 W Operating Temperature: 0 ~ +40 °C Storage Temperature: -30 ~ +80 °C Operating Humidity Range: 10~85%, RH, Non-condensing Size (WxDxH) in mm:...