Subscribe to Our Youtube Channel
Related Manuals for miseno MH00130CS
Summary of Contents for miseno MH00130CS
- Page 1 MODEL #. MH00130CS MH00136CS Installation, Use and Care Guide READ AND SAVE THESE INSTRUCTIONS 2014.SEP...
- Page 2 www.build.com...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifi cations ........... Mounting the Hood ............. Ductless Recirculating ..........FEATURES & CONTROLS Mechanical Controls ..........MAINTENANCE Hood and Filter Cleaning .........
- Page 4 www.build.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product. A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary. MH00130CS & MH00136CS - 400 Watts, 3.3 Amps...
- Page 6 MODELS: MH00130CS & MH00136CS PARTS SUPPLIED 1 - Hood with internal blower 1 - Duct cover wall bracket 1 - Duct cover assembly (top and bottom) 1 - Hardware package 1 - 6” round backdraft damper (pre-installed) 2 - 50W GU-10 halogen light bulbs...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8”...
- Page 8 www.build.com Minimum mount height between range top to hood bottom should be no less than 26”. Maximum mount height should be no higher than min. ducted 27-1/2” min. recirc. 32” 34”. max. 42-1/2” It is important to install the hood at the proper mounting height.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certifi...
- Page 10 www.build.com Standard Duct Cover Min. ducted 27- ” Min. recirc. 32” Max. ducted 42- ” RHEX001S Extension Min. ducted 46- ” Min. recirc. ” Max. ducted 80”...
- Page 11 CAUTION: At least two installers are required due to the weight and size of the hood. 1. Measure from range top to hood bottom and mark line A. (26” minimum from range top) . Duct Cover Bracket 2. Plum and mark center line. 3.
- Page 12 Kit includes charcoal lters, charcoal lter brackets and air diverter plate. Hood Model Part No. Filters & Brackets in Pkg. MH00130CS / MH00136CS RHRK001S 1. Purchase recirculating kit per the part number above 2. Secure air diverter plate to wall below duct cover bracket. (FIG. B) Run 6”...
- Page 14 www.build.com SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain.
-
Page 15: Replacing Light Bulbs
REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. - Page 16 TROUBLESHOOTING PROCEDURES FOR MH00130CS & MH00136CS After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 18 www.build.com DESCRIPTION PART# Replacement Parts Light Bulb GU-10 50W (each) Z0B-0020 Optional Accessories Recirculating Kit RHRK001S Replacement Charcoal Filter (each) RHCF001 Extension Duct Cover RHEX001S To order parts, email us at vsupport@ventingservices.com or call us at 1.888.750.1698...
- Page 19 STAPLE YOUR RECEIPT HERE Proof of the original purchase Limited Warranty date is needed to obtain service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-750-1698 Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...
Need help?
Do you have a question about the MH00130CS and is the answer not in the manual?
Questions and answers