Subscribe to Our Youtube Channel
Related Manuals for miseno MH70330AS
Summary of Contents for miseno MH70330AS
- Page 1 MODEL #. MH70330AS MH70336AS Installation, Use and Care Guide READ AND SAVE THESE INSTRUCTIONS 2015.OCT...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options .......................... Electrical ................. Mounting the Range Hood ........Vertical Rectangular Ducting Conversion ..Horizontal Ducting Conversion ......FEATURES & CONTROLS Rotary Dial ..............
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION attics, crawl spaces or garages. Not for use over an outdoor grill. OPERATION and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product.
- Page 6 MODELS: MH70330AS, MH70336AS PARTS SUPPLIED 1 - Hood with internal blower pre-installed 1 - Residue Tray 1 - Rectangular starting collar 1 - Rectangular transition adaptor 1 - Hardware package HARDWARE PACKAGE CONTENTS Suction Cup (1) M6 x 2” (4) M6 x 1-1/2”...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 3- 1/ 4” x 10” 5 Ft. Rect., Rect. to straight 6” round transition 6”, 7”, 8”, 10” 1 Ft.
- Page 8 Minimum mount height between range top to hood bottom should be no less than 24”. Maximum mount height should be no higher than 32”. It is important to install the hood at the proper mounting height. Hoods mounted too low could 8"...
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Some Ducting Options Roof Pitch w/ Flashing & Cap Side wall cap w/ gravity damper Rear Ducting...
- Page 10 ” ” ” (30“) , 35 ” (36”) 15/16 15/16 12” 8” 3” ” side ” ” 13/16 back...
- Page 11 ELECTRICAL WARNING how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances. Electrical Supply: This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
- Page 12 For Mounting Under a Kitchen Cabinet options. 5. Duct opening 2. Measure and cut out duct and electrical openings cutout in cabinet or wall to match up with the hood. Ducting and electrical dimensions can be found on Page 8. Note: Make sure duct opening is duct/silver large enough to apply aluminum duct tape to the tape...
- Page 13 3-1/4"x10" Rectangular Vertical Ducting 1. Using a Philips-head screwdriver remove the screws and rectangular transition adapter. Do not secure to hood body yet. transition adapter. Secure rectangular adapter and rectangular collar to hood body using the previously removed screws from step 1.
- Page 14 3-1/4"x10" Rectangular Horizontal Ducting 2. Using a Philips-head screwdriver, remove the screws 1. Using a Philips-head screwdriver remove the screws hood. 3. Remove the two plastic air diverter blocks. The blocks rectangular transition adapter. Do not secure to hood body are located in the hood and can be accessed from the top yet.
- Page 15 1 Blower On/Off/Speed Selection 2 Lights Dim/Bright/Off 1 Blower On/Off/Speed Selection Rotate dial to change speed levels, (1) for low speed, (2) for medium speed and (3) for high speed 2 Lights Dim/Bright/Off Rotate dial to change light settings, (1) for dim light and (2) for bright light...
- Page 16 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless should never need replacing, they are required to be cleaned every 30 days or more often depending on cooking habits.
- Page 17 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise.
- Page 18 TROUBLESHOOTING PROCEDURES FOR MH703 Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 19 CIRCUIT DIAGRAM Model MH70330AS/MH70336AS Voltage 120V 60Hz Power consumption Total: Max. 225W @ 2A Lamp: Max. 35Wx2 Fan: Max. 155W THERMALLY PROTECTED...
- Page 20 DESCRIPTION PART # Replacement Parts To order parts, please call us at 1.888.750.1698...
- Page 21 STAPLE YOUR RECEIPT HERE Proof of the original purchase Limited Warranty date is needed to obtain service under warranty TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call: 1-888-750-1698 Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you”...
Need help?
Do you have a question about the MH70330AS and is the answer not in the manual?
Questions and answers