Related Manuals for Lanzar Lanzar Vibe VBD300
Summary of Contents for Lanzar Lanzar Vibe VBD300
- Page 1 OWNER’S MANUAL VBD 300 PLL SYNTHESIZER STEREO RADIO WITH COMPACT DISC PLAYER DIGITAL...
-
Page 2: Installation
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. •... -
Page 3: Din Rear-Mount (Method B)
(Fig. 2) Removing the unit DIN REAR-MOUNT (Method B) Installation using the screw holes on the sides of the unit. 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secure the back of the unit in place. -
Page 4: How To Remove And Install The Front Panel
HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL) 1. Press the release button and pull-off the front panel. Keep front panel into the case. 2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnormalities occurs on the display or some keys will not function properly. -
Page 5: Wiring Connection
WIRING CONNECTION ANTENNA CONNECTOR IGNITION SWITCH (B+) YELLOW MEMORY CHOKE BACK-UP BLACK GROUND (B–) BLUE POWER ANTENNA FRONT Lch – SPEAKER WHITE/BLACK REAR Lch – SPEAKER GREEN/BLACK WIRING CONNECTION ANTENNA CONNECTOR IGNITION SWITCH (B+) CHOKE BOX YELLOW MEMORY BACK-UP BLACK GROUND (B–) POWER ANTENNA... -
Page 6: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS (1) ON/OFF Press POWER button (1) to turn on. Press it again to turn it off. If the power is off, press BND button (11) or MOD button (12) also can turn on the unit. (2) DISC PLAY Gently insert a compact disc with the label side facing up into the disc slot (2). - Page 7 (4) MONO/STEREO (FOR MON VERSION ONLY) Press MON button (4) to select monaural or stereo (Mono reception for radio stations). You can sometimes improve reception of distant stations by selecting mono operation. (4) SUB-WOOFER (FOR SUB.W. VERSION ONLY) Press X-BAS button (4) to toggle sub-woofer output, when sub-woofer on, display will show “...
- Page 8 The LCD (13) can show the current state of the unit. Press and release a TUNE/SEEK/TRACK button to move radio frequency number up or down on step. Press and hold a TUNE/SEEK/TRACK button seconds to seek the next clear station. Press a TUNE/SEEK/TRACK button track or the following track.
-
Page 9: Faceplate Release
(23) AUTOMATICALLY STORING & PROGRAM SCANNING Automatically Storing Press and hold AMS button (23) for several seconds to toggle automatically storing function. It starts searching next frequency in local mode and stores the clear station into the preset memory. If 6 ch. is not fully memorised, it would start the second searching in distance mode. -
Page 10: Remote Control Handset
Remote Control Handset Control & Function Keys 1. POWER 2. MOD 3. SEL 4. EQ 5. BND 6. MUTE 7. VOL + 8. VOL – 9. TUN/SEK 10. TUN/SEK 11. PRESET 12. TOP 13. SCN 14. RPT 15. RND = Power ON/OFF Button = Mode Button = Select Button = Equalization Button... -
Page 11: Specification
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power - Version v - Version z - Version y CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity (S/N = 30 dB) : 3 V... -
Page 12: Troubleshooting
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. The car ignition is not on. The fuse is blown. Disc cannot Presence of CD disc be loaded or...