Download Print this page

Novatel FlexPak-G2-V1 Quick Start Manual page 3

Gps and glonass receiver

Advertisement

ENTERING COMMANDS
NovAtel receivers use a comprehensive command interface.
Commands can be sent to the FlexPak using the Console
window in CDU, which is opened from the View menu. Enter
commands in the text box at the bottom of the Console window.
The following information is important when entering commands:
Commands can be entered in three formats:
ASCII (log bestposa)
Abbreviated ASCII (log bestpos)
Binary (log bestposb).
Abbreviated ASCII is the best format to use when you
wish to work with the receiver directly. For data
collection, use ASCII or Binary.
Press the Enter key to send the command string to the
receiver.
The commands are not case sensitive.
The Quick Reference Guide provided with the receiver lists the
available commands and the parameters they use for the
Abbreviated ASCII format.
LOGGING DATA
An extensive collection of logs has been created to capture the
data your FlexPak receives and processes. These logs can be
directed to any of the FlexPak's serial ports and can be
automatically generated when new or changed data becomes
available or at regular intervals. The available logs are listed in
the Quick Reference Guide.
To log data, use the LOG command. For example, to log the
pseudorange position to COM 2 every 30 seconds, enter the
following:
LOG COM2 PSRPOS ONTIME 30
Logs can be generated in one of three formats: ASCII,
Abbreviated ASCII, or Binary. Refer to the Firmware Reference
Manual for information on the LOG command, specifying the
output format, and the detailed contents of each log.
If you prefer, CDU provides a graphical interface for configuring
data logging. Select Logging Control Window from the Tools
menu. In the Logging Control window, you can select which logs
to capture and choose to which ports to send the data. In
addition, you can specify a file in which to save the data.
ENABLING SBAS POSITIONING
FlexPak-G2 models are also capable of SBAS positioning. This
positioning mode is enabled using the SBASCONTROL command.
The following commands are typically used to enable WAAS
(North America) and EGNOS (Europe) respectively:
SBASCONTROL ENABLE WAAS
SBASCONTROL ENABLE EGNOS
Once enabled, the Position Type field shown in CDU's Position
window should change from Single to WAAS and you may see
SBAS satellites in the Constellation window.
ENABLING L-BAND POSITIONING
(FlexPak-G2-V1 only)
L-Band equipped receivers allow you to achieve sub-meter
accuracy. To use this positioning mode, you must enable L-band
tracking to the Canada-Wide Differential GPS (CDGPS) or
OmniSTAR signal. A subscription to OmniSTAR is required to
use the OmniSTAR service (visit
http://www.omnistar.com
have your receiver's serial number ready). The CDGPS signal is
free and available without subscription over North America (visit
http://www.cdgps.com).
The ASSIGNLBAND command allows you to set OmniSTAR or
CDGPS base station communication parameters. It should
include a relevant frequency and data rate. The frequency
assignment can be made in Hz or KHz. For example:
Hz:
assignlband omnistar 1536782000 1200
KHz: assignlband omnistar 1536782 1200
A value entered in Hz is rounded to the nearest 500 Hz.
To confirm you are tracking an L-Band signal, log the L-Band
status information by entering:
log lbandstat
For example, if you are receiving CDGPS, the fifth field after the
header, which is the L-band status, will be 0082:
lbandstata com1 0 43.5 finesteering 1295
149951.671 00000000 976f 34461;
1547546977 46.18 4541.0 0.00 0082 00f0 ...
To specify the correction source, use the PSRDIFFSOURCE
command as shown in the examples below:
or,
PSRDIFFSOURCE OMNISTAR
PSRDIFFSOURCE CDGPS
otherwise it is left at the default AUTOMATIC.
Refer to the OEMV Family Firmware Reference Manual for more
on individual L-Band (FlexPak-G2-V1 only), GLONASS (FlexPak-
G2-V1G or FlexPak-G2-V2) or SBAS commands and logs.
and

Advertisement

loading

This manual is also suitable for:

Flexpak-g2-v1gFlexpak-g2-v2Flexpak-g2-oemstar