Page 1
ZKTeco FR1200 User Manual Version: 1.0.1 Date: Dec. 2011 Introduction: This document mainly introduces the user’s operation of ZKTeco FR1200. About the device installation, please refer to the Installation Guide.
1. Using Instruction 1. Using Instruction 1.1 Finger Placement Enroll fingerprint by pressing index finger, middle finger or ring finger (thumb and little finger are clumsy). 1. Proper press: Make finger center pressed on the sensor window. 2. Improper press: Upright Too lean Slant Too low Please adopt the correct way to place the finger to avoid improper operation led to the identification performance degradation. 1 ...
ZKTeco FR1200 User Manual V1.0.1 1.2 Instruction for Card Using Integrated with a noncontact RF card reader module, this reader supports the ID cards and Mifare cards (Optional and only used as ID cards). By offering multiple verification modes such as FP, card, FP plus card, FP or card verification, this reader can accommodate to diversified user needs. Swipe your card across the sensor area following the light and beep prompts and ...
2. Device Introduction 2. Device Introduction FR1200, a fingerprint reader with RS485 communication interface works with biometric access controllers and fingerprint standalone access control. It offers the function of capturing and transferring fingerprint samples to access control panel inside to match. With its IP65 rated rugged structure. This reader operation is simple and flexible. The light and beep prompts will guide you through all the operations without screen display or keyboard. Featuring a compact and simple design, this ...
Page 6
ZKTeco FR1200 User Manual V1.0.1 Operation succeeds: The green indicator is solid on for one second, at the same time the speaker play one long beep. Operation failed: The red indicator is solid on for one second, at the same time the speaker play two short beep. Verification state: The green LED blinks once every two second, the beeper with no sound. ² Card Sensor Area: Refers to the area in the red dashedline as shown in the figure above. ² Fingerprint Sensor: Used to enroll and match fingerprints. Bottom view: Reset Button ² Reset Button: Used to restart the reader. ...
ZKTeco FR1200 User Manual V1.0.1 3. Device Operations After the reader is powered on, the reader can not identify the fingerprint or card. In other words, the reader can not receive data or send data without access control panel connection. Only when the reader connected with the access control panel that the reader can prompt if the card or fingerprint is enrolled or not, and verify the user according to the returning result of background access control panel. User verification operations: 1. When the reader connected with the access control panel, it is in verification state, the beep with no sound, and the green LED blink once every two second to prompt verification. 2. Start user verification. The reader supports four verifications modes: only ...
Page 9
3. Device Operations setting time, 2 beep and red LED solid on for verification failed, 1 beep and green LED solid on for verification succeed. Card plus fingerprint verification: Determine if there is the card data. If you swipe card near to the card reader, then send the fingerprint template and card data to the access control panel, and wait for the result. If it is waiting time out, beep 3 sounds and the red LED solid on. If the reader get the verification result in the setting time, 2 beep and red LED solid on for verification failed, 1 beep and green LED solid on for verification succeed. Only card verification: No sending of the data to access control panel, the device beeps 2 sounds, and red LED solid on. ...
Page 10
ZKTeco FR1200 User Manual V1.0.1 The verification operations are as follows: Reader Start Get FP template, 1 beep, light off, switch to 485 Getting control order timeout? N Y Only FP verification? N Y FP or card verification? N Get card number Y FP and card N already?? verification? Send FP template to Y N access control panel Send card number Only card and FP template to verification? access control panel Y Verification result timeout? N N ...
Page 11
3. Device Operations Swipe card first: (1) Swipe your card on the card reader in a proper way. The device beeps once, and then the LED off, switch to the background verification. (2) The access control panel determines whether the control order is timeout. If it is timeout, the device beeps 3 sounds and the red LED solid on. Otherwise, get the system verification modes setting. Only card/card or fingerprint verification: Send the card data to the access control panel, and wait for the result. If it is waiting time out, beep 3 sounds and the red LED solid on. If the reader get the verification result in the setting time, 2 beep and red LED solid on for verification failed, 1 beep and green LED solid on for verification succeed. ...
Page 12
ZKTeco FR1200 User Manual V1.0.1 The verification operations are as follows: Reader Start Get card, 1 beep, light off, switch to 485 Y Getting control order timeout? N Only card Y verification? N Y FP or card verification? Send card number N to access control Y Only card verification? Y Verification N result timeout? FP and card N verification? N Pass the Y verification? Send no data to access control panel, switch to main mission, waiting for FP and follow the ...
4 Appendix 4 Appendix 4.1 List of Parameters The following table lists the basic functional parameters of the reader. Item Note Power Supply DC12V/3A External Function EXT 485 for access control panel connection Verification mode. ID (Mifare) card, fingerprint Communications RS485 Speaker Beep prompt LED Bicolor indication (red/green) 11 ...
ZKTeco FR1200 User Manual V1.0.1 4.2 Statement on Human Rights and Privacy Dear Customers: Thank you for choosing the multibiometric products designed and manufactured by us. As a worldrenowned provider of biometric technologies and services, we pay much attention to the compliance with the laws related to human rights and privacy in every country while constantly performing research and development. We hereby make the following statements: 1. All of our fingerprint recognition readers for civil use only collect the characteristic points of fingerprints instead of the fingerprint images, and therefore ...
Page 15
4 Appendix 2. The personal dignity of citizens of the People's Republic of China is inviolable. 3. The home of citizens of the People's Republic of China is inviolable. 4. The freedom and privacy of correspondence of citizens of the People's Republic of China are protected by law. At last we stress once again that biometrics, as an advanced recognition technology, will be applied in a lot of sectors including ecommerce, banking, insurance and legal affairs. Every year people around the globe suffer from great loss due to the insecurity of passwords. The fingerprint recognition actually provides adequate protection for your identity under a high security environment.
ZKTeco FR1200 User Manual V1.0.1 4.3 EnvironmentFriendly Use Description The Environment Friendly Use Period (EFUP) marked on this product refers to the safety period of time in which the product is used under the conditions specified in the product instructions without leakage of noxious and harmful substances. The EFUP of this product does not cover the consumable parts that need to be replaced on a regular basis such as batteries and so on. The EFUP of batteries is 5 years. Names and Concentration of Toxic and Hazardous Substances or Elements Toxic and Hazardous Substances or Elements Parts Name Pb Hg Cd Cr6+ PBB PBDE ¡ ¡ ¡ ¡...