Page 1
SERVICE MANUAL VHF FM TRANSCEIVER iF310 iF310S iF320 iF320S...
Page 2
IC-F310 MAIN UNIT 5 pieces 6. DO NOT transmit power into a signal generator or a 8810005840 Screw PH BT M3 x 8 NI-ZU IC-F310 Bottom cover 10 pieces sweep generator. Addresses are provided on the inside back cover for your 7.
Page 3
SEMI-CONDUCTOR INFORMATION SECTION 9 BOARD LAYOUTS 9 - 1 FRONT UNIT (IC-F310/F320) ........................9 - 1 9 - 2 FRONT UNIT (IC-F310S/F320S) .........................9 - 3 9 - 3 MAIN UNIT (IC-F310/F310S) ........................9 - 5 9 - 4 MAIN UNIT (IC-F320/F320S) ........................9 - 7...
Page 5
SECTION 2 INSIDE VIEW Power module (IC1) PLL IC (IC2: UPD3140GS) Low-pass filter CPU5V Regurator (IC9: S-81250PG-PD) ANT SW RF amplifier AF power amplifier (Q12: 35K239) (IC10: LA4425A) 1st IF filter (FI1: FL-285) High-pass filter (IC8: NJM2904V) FM IF IC *AF switching IC (IC3: TA31136FN) (IC4: BU4066 BCFV)
Page 6
SECTION 3 DISASSEMBLY INSTRUCTIONS • Opening case 6 Lift the front portion of the main unit and remove it. 1 Unscrew 4 screws, A, and remove the bottom cover. 2 Unscrew 2 screws, B, and remove the front case. • Instration location UT-96 TONE UNIT UT-105 SmarTrank 2 Logic Board...
SECTION 4 CIRCUIT DESCRIPTION 4-1 RECEIVER CIRCUITS 4-1-3 1ST MIXER AND 1ST IF CIRCUITS (MAIN unit) 4-1-1 ANTENNA SWITCHING CIRCUIT (MAIN unit) The 1st mixer circuit converts the received signals to a fixed The antenna switching circuit functions as a low-pass filter frequency of the 1st IF signal with the PLL output frequency.
4-1-5 AF AMPLIFIER CIRCUIT (MAIN unit) A portion of the AF signals from the AF amplifier (IC7a) passes through the low-pass filter (FRONT unit; Q5) to The AF amplifier circuit amplifies the demodulated AF sig- remove AF (voice) signals and is applied to the CTCSS or nals to drive a speaker.
(IC1) to obtain 45 W (for IC-F320; 25 W for sists of the PLL IC (IC2), loop filter and reference oscillator IC-F310) of RF power. circuit and employs a pulse swallow counter. The amplified signal is passed through the antenna switch-...
4-4 POWER SUPPLY CIRCUITS 4-4-1 VOLTAGE LINES (MAIN unit) CPU (IC1)—continued Description Line Port Description number name The voltage from a DC power supply. Outputs RF attenuator control signal to The same voltage as the VCC line which is con- RFATT the attenuator switch (MAIN unit;...
Page 11
4-5-2 I/O expander IC (1) IC5 (MAIN unit) Port Description number name Output tunable band pass filter control 2, 3, 10 T1–T3 signals. Output port for tunable band pass filter control sig- nal whiler receiving. output power control signal while transmitting.
Page 12
↑ / ↓: Cursor Up/Down [Enter] at TXF: REF Set Mode < / > : –/+ ESC : Quit /B: This does not activate for IC-F310/F320’s adjust- ment. RS-232C port number. NOTE: When the EEPROM (FRONT unit; IC3) is replaced or the transceiver displays an error message and beeps, the following operation is necessary before starting the ADJUSTMENT.
Page 13
‘ ‘ PROGRAM SCREEN EXAMPLE ∗∗∗∗∗ Trimmer Control Software for IC–F300 Series ∗∗∗∗∗ Rev. 1.0 Connected DC voltage A/D VIN 177 : B1h 13.88V D/A BP T1 170 : AAh 2.93V Internal temperature D/A BP T2 188 : BCh 3.16V A/D TEMPS 180 : B4h 27.70'C...
5-2 PLL ADJUSTMENT ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST PLL LOCK • Operating frequency: (Ch 1) MAIN Connect a digital 3.5 V [L-band] MAIN VOLTAGE 155.00000 MHz [L-band] multi-meter or oscil- 4.0 V [H-band] 174.00000 MHz [H-band] loscope •...
Page 15
5-3 TRIMMER ADJUSTMENT Select an operation using [↑] / [↓] keys, then set specified value using [←] / [→] keys on the connected computer keyboard. MEASUREMENT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION REFERENCE • Operating frequency : (Ch 1) Rear Loosely couple a frequency 155.00000 MHz FREQUENCY...
Page 16
TRIMMER ADJUSTMENT — continued Select an operation using [↑] / [↓]keys, then set specified value using [←] / [→] keys on the connected computer keyboard. MEASUREMENT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION RECEIVE • Operating frequency: (Ch 2) Rear Connect a SINAD meter with a 4 Minimum distortion Ω...
Page 17
• MAIN unit SINAD DC power supply 13.2 (13.6) V / 15 A meter millivoltmeter Speaker 4 Ω Audio – generator J2, pin 25 Audio input point • FRONT unit Beep level adjustment 5 - 6...
Page 32
9-3 MAIN UNIT (IC-F310/IC-F310S) ¡ ¡ TOP VIEW NOTE: L19, 20, 21, 22 should be mounted as the appointed direction. TOP VIEW INDICATION to FRONT unit SPGND to Speaker HORN to Optional cable to Optional unit 9 - 5...
Page 34
9-4 MAIN UNIT (IC-F320/F320S) ¡ ¡ TOP VIEW NOTE: L19, 20, 21, 22 should be mounted as the appointed direction. TOP VIEW INDICATION to FRONT unit SPGND to Speaker HORN to Optional cable to Optional unit 9 - 7...
Page 36
SECTION 10 BLOCK DIAGRAM RIPPLE x1 or x2 LOOP TX/RX DRIVE BUFF BUFF BUFF BUFF C60.C61 Q7.Q8 D5.D6 D3.D4 COMMON LINE L1.L2.L3 D7.D8 D13.D14 L17.L18 LINE DISC PLST RX LINE DTCS UNLK BUFF 2nd Lo TX LINE MAIN UNIT CTRL L23.L24 FM DET 1st LO...
Page 37
SECTION 11 VOLTAGE DIAGRAM ¡ ¡ FRONT UNIT LED type only (LED type only) Connect to IC1(pin 69 pin 75) DS12 LCD type only LD-HU10140J SEG1 (LCD type only) SEG1 SEG2 FRONT UNIT SEG2 DS13 SEG3 (LCD type only) SEG3 SEG4 MEASUREMENT CONDITIONS SEG4...
Need help?
Do you have a question about the IC-F310 and is the answer not in the manual?
Questions and answers