Advertisement
Page 6
SB-2-253-I
Troubleshooting (continued)
CONDITION
Fluid leaking or dripping
from front of gun
Runs and sags
Thin, sandy coarse finish
drying before it flows out
Thick, dimpled finish
"orange peel".
ACCESSORIES
WR-103
42884-214-K5
3/8"
Wrench
42884-215-K10
5/8"
Cleaning Brushes
Contains all neces-
These brushes are
sary tip, hose and
helpful in cleaning
nut sizes used on or
threads and re-
with gun.
cesses of gun body.
®
192218 Scrubs
JGA-156-K10
Hand Cleaner
Spring Clip
Towels
Joins any single
piece DeVilbiss air
cap with latest ver-
P r e m o i s t e n e d
sion MBC-368 or
waterless hand
MSA-1 retaining ring.
cleaner towels for
Helps prevent parts
painters, body men
loss and provides
easier assembly.
and mechanics.
DeVILBISS WORLDWIDE SALES AND SERVICE LISTING - www.devilbiss.com
AUTOMOTIVE REFINISHING
DeVilbiss has authorized distributors throughout the world. For equipment, parts and service, check the Yellow Pages
under "Automobile Body Shop Equipment and Supplies". FOR TECHNICAL ASSISTANCE, CALL TOLL FREE
1-800-445-3988 (U.S.A. ONLY). FOR LOCAL CALLS, SEE LISTING BELOW.
U.S. Customer Service Office
MAUMEE, OH 43537
CAUSE
Packing nut too tight.
Dry packing.
Fluid tip or needle worn or damaged.
Foreign matter in tip.
Fluid needle spring broken.
Wrong size needle or tip.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun motion
too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Too much material coarsely atomized.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
HAV-500 OR
HARG-510
HAV-501
Air Regulator
Adjusting
Valve
(HAV-501 SHOWN)
Use to maintain
nearly constant out-
let pressure despite
HAV-500 does not
changes in inlet
have
pressure
pressure and down-
gauge. Use to con-
stream flow.
trol air usage at gun.
TGC-545 (Alum.)
JGA-4005 Air
PTFE
TLC-555 (PTFE
Adjusting Valve
Lined), 2 Qt. Drip
Free Suction Cup
Cup has a unique,
Installs into gun to
two position valve
enable user to con-
which permits selec-
trol and reduce air
tion of either a drip-
usage at the gun.
free or conventional
Replaces JGA-132
open vent mode.
plug.
1724 Indian Wood Circle
8/02
©Copyright 2002, DeVilbiss,
CORRECTION
Adjust.
Lubricate.
Replace tip and needle with lapped sets.
Clean.
Replace.
Replace.
Adjust gun or reduce fluid pressure.
Mix properly or apply light coats.
Hold gun at right angle to work and adapt to
proper gun technique.
Check distance. Normally approx. 6-8".
Reduce air pressure and check spray pattern.
Follow paint manufacturer'smixing instructions.
Check distance. Normally approx. 6-8".
Air pressure too low.
Increase air pressure or reduce fluid pressure.
Follow paint manufacturer'smixing instructions.
Follow paint manufacturer'smixing instructions.
Properly clean and prepare.
MSP-524 Twin
Spray Gun Lube
Cartridge,
SSL-10
Paint Spray
Respirator
Compatible with all
NIOSH-Certified
paint materials: con-
(TC-84A-1623 for
tains no silicone or
respiratory protec-
petroleum distil-
tion in atmospheres
lates to contaminate
not immediately
paint. MSDS avail-
dangerous to life.
able upon request.
HAF-507
Automotive Quick Connects For HVLP
Whirlwind™
Guns (Air)
In-Line Air Filter
HC-4419 Stem
1/4" NPT(F)
Removes water, oil,
HC-1166 Stem
and debris from the
1/4" NPT(M)
air line.
Address
Automotive Refinishing
192212 Professional
Spray Gun Cleaning Kit
Contains six precision tools
designed to effectively clean
all DeVilbiss, Binks, Finishline
and other brand spray guns.
High Flow Type.
HC-4719
Coupler
1/4" NPT(M) /
NPS(M)
HC-4720
Coupler
1/4" NPT(F)
Telephone No.
(419) 891-8100
Printed in U.S.A.
Hide quick links:
Advertisement
