Subscribe to Our Youtube Channel
Related Manuals for Hilti SCW 18-A
Summary of Contents for Hilti SCW 18-A
- Page 1 SCW 18-A Operating instructions Mode d’emploi Manual de instrucciones Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
- Page 2 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
- Page 3 Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
- Page 4 Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
- Page 5 Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
-
Page 6: Table Of Contents
SCW 18‑A cordless circular saw In these operating instructions, the designation “the It is essential that the operating instructions power tool” always refers to the SCW 18-A cordless are read before the power tool is operated for circular saw. the first time. -
Page 7: Description
Sawing metals is not permissible. Do not use the power tool to cut tree branches or logs. Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. - Page 8 C < 10 % 2.8 Items supplied as standard Power tool Saw blade Hexagon socket wrench Operating instructions Hilti toolbox (optional) Cardboard box (optional) Rip fence / parallel guide (optional) Connecting piece for sawdust extractor (op- tional) Guide rail adapter (optional) 2.9 Additional items required for operating the tool...
-
Page 9: Accessories
3 Accessories Accessories for the SCW 18‑A Designation Short designation Charger for Li-ion batteries C 4/36 Charger for Li-ion batteries C4/36-ACS Charger for Li-ion batteries C 4/36‑90 Charger for Li-ion batteries C 4/36‑350 Battery B 18/3.3 Li‑Ion Battery B 18/2.6 Li‑ion Rip fence Guide rail 4 Technical data... -
Page 10: Safety Instructions
5 Safety instructions NOTE not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A The safety rules in section 5.1 contain all general safety moment of inattention while operating power tools rules for power tools which, in accordance with the may result in serious personal injury. - Page 11 Keep cutting tools sharp and clean. Properly main- When ripping, always use a rip fence or straight tained cutting tools with sharp cutting edges are less edge guide. This improves the accuracy of cut and likely to bind and are easier to control. reduces the chance of blade binding.
- Page 12 g) Use extra caution when sawing into existing walls Do not touch the clamping flange or the clamping or other blind areas. The protruding blade may cut screw while the power tool is running. objects that can cause kickback. m) The kerf must be free of obstructions. Do not saw into screws and nails etc.
-
Page 13: Before Use
Place the tool in a location where it can be kept under observation, well away from flammable materials, and allow it to cool down. Contact Hilti Service after the battery has been allowed to cool. Before beginning work, check the working area (e.g. -
Page 14: Operation
(trans- switched off and the switch-on interlock is activated port position). (not pressed). Use only the Hilti batteries approved for use with this power tool. If you disconnect a battery from the power tool for trans-... - Page 15 Release the clamping screw by turning the wrench Secure the workpiece so that it can not move. further clockwise. Position the workpiece so that the saw blade is free Remove the clamping screw from the outer clamping to move under the workpiece. flange.
-
Page 16: Care And Maintenance
Position the guide rail with the zero mark at the edge CAUTION of the workpiece and then pivot the rail until the As far as possible, use a suitable Hilti sawdust extrac- desired angle shown on the angle scale is opposite tor/deduster, whatever the application. Use a respi- the zero mark. -
Page 17: Troubleshooting
Do not operate the power tool if parts are 8.4 Cleaning the safety devices damaged or when the controls do not function faultlessly. Have the power tool repaired by Hilti Service. Remove the saw blade before cleaning the safety devices. -
Page 18: Disposal
Dispose of the batteries in accordance with national regulations or return them to Hilti. Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. - Page 19 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3927 | 0214 | 00-Pos. 3 | 1 Printed in China © 2014 Right of technical and programme changes reserved S. E. & O 434722 / A4 Printed: 12.03.2014 | Doc-Nr: PUB / 5135507 / 000 / 02...
Need help?
Do you have a question about the SCW 18-A and is the answer not in the manual?
Questions and answers