Zennio Z41 User Manual
  1. Manuals
  2. Brands
  3. Zennio Manuals
  4. Touch Panel
  5. Z41
  6. User manual

Zennio Z41 User Manual

Knx capacitive colour touch panel
Hide thumbs Also See for Z41:
Table of Contents

Advertisement

Quick Links

KNX Capacitive Colour Touch Panel
ZN1VI-TP41C
Application Program Version: [3.0]
User Manual Version: [3.0]_a
www.zennio.com

Advertisement

Table of Contents
loading

Related Manuals for Zennio Z41

Summary of Contents for Zennio Z41

  • Page 1 KNX Capacitive Colour Touch Panel ZN1VI-TP41C Application Program Version: [3.0] User Manual Version: [3.0]_a www.zennio.com...

  • Page 2: Document Updates

    • Revision and update of communication object flags. • Customisable function for the Reset button. • Object name changed: “[Energy x] Cost”. New Annex (Controlling Z41 Remotely via IP). 3.0_a 6, 7, 9, Device Pairing function.
  • Page 3 InZennio Z41 Changes in the application program: • Parameter added for setting the attenuation of the backlight (total, partial or none) on inactivity. • Support added for TrueType fonts. • Compatibility with Greek and Cyrillic characters. • Driver update to offer compatibility with newer capacitive touch panels.

  • Page 4: Table Of Contents

    InZennio Z41 Contents Document Updates ........................2 Introduction ........................6 InZennio Z41 ......................6 Z41 2.x (and later versions) ..................8 Installation ........................ 9 1.3.1 Firmware Updates .................... 11 Configuration ........................12 Menu Page ......................12 General-Purpose Pages .................... 13 Profile Page ......................
  • Page 5 Configuration ....................75 Configuration Page ....................75 3.6.1 Configuration ....................75 Thermostat n ......................76 ANNEX I. Controlling Z41 Remotely via IP ................78 Configuring Z41 ........................78 Pairing Procedure........................ 79 Remote Applications ......................80 ANNEX II. Communication Objects ..................81 http://www.zennio.com...

  • Page 6: Introduction

    Elegant design, available in various colours. Note that a major enhancement in the functionality and an innovative re-design of the original user interface were introduced by Zennio beginning with version 2.0 of the application program. Table 1 shows the most significant functionalities and differences of versions 1.x, 2.x and 3.0 (or later).
  • Page 7 (**) Only positive numeric values. (***) This differentiation does not apply anymore; six pages are now provided combining all the functionalities together. Note: the following sections of this user manual will focus on the Z41 3.0 application program. http://www.zennio.com Tecnical Support:...

  • Page 8: Z41 2.X (And Later Versions)

    InZennio Z41 1.2 Z41 2.x (AND LATER VERSIONS) Versions 2.0 and later of the Z41 application program feature the following functions: 6 General-Purpose Pages, with up to 8 Fully-Customisable Boxes each, which the integrator may configure as indicators or controls.

  • Page 9: Installation

    –positive and negative– from the supply to the device. In addition to the external supply, Z41 makes use of a button battery (LR44), located at the corresponding slot (7), to help maintain the time and date updated in case of a failure of the external power supply.
  • Page 10 Once it reaches 100%, the Status page will disappear and the Menu page will come up. The “Ethernet” box shows the IP address assigned to Z41, provided that an Ethernet cable has been attached (6) and the network is running a DHCP server.

  • Page 11: Firmware Updates

    The programming LED (3) will then light in red. On the contrary, if this button is held while the device gets connected to the bus, Z41 will enter the safe mode. In such case, the programming LED will blink in red colour.

  • Page 12: Configuration

    2 CONFIGURATION 2.1 MENU PAGE The user interface of the InZennio Z41 touch screen is organised into pages (up to eight different pages), each of which can be accessed from the Menu page, which (unless parameterised the contrary) is automatically shown after the start-up of the device.

  • Page 13: General-Purpose

    InZennio Z41 Figure 4 Menu button 2.2 GENERAL-PURPOSE PAGES The integrator can make use of up to 6 general-purpose pages, each of which can hold up to 8 different indicators or controls (with no restrictions for combining them) which will show inside the pages, automatically distributed or not, according to page parameterisation.
  • Page 14 InZennio Z41 Theme: desired colour combination, among eight different options: Figure 6 Themes Melody: desired tune (among three different options) for the beeps emitted on button presses or as a feedback on action executions. One more possibility is to make these beeps silent (however alarm beeps will still work).

  • Page 15: Configuration Page

    Figure 8 Time-Set Control Z41 features an internal clock powered by a battery (see section 1.3), because of which the time/date will not be lost after downloads or reboots. Programming Button: control/indicator that shows the status of the programming LED of the device.
  • Page 16 InZennio Z41 programming mode as by pressing the actual programming button of the device (see section 1.3) in case the rear of Z41 cannot be accessed. Reset: holding this button for a few seconds (i.e., a long press is required) sets the device back to a certain state, which can be set in ETS: ...
  • Page 17 Device Pairing: button for entering the device pairing function, which needs to be run once on every Z41 that is intended to be controlled from a remote IP application. See ANNEX I. Controlling Z41 Remotely via for more details about controlling Z41 remotely.

  • Page 18: Backlight

    InZennio Z41 2.5 BACKLIGHT In order to prevent unnecessary power consumptions while the device is idle, Z41 automatically fades partially out the backlight of the screen after two minutes without any user interaction. Next, after three more minutes of inactivity (i.e., after five minutes of inactivity), the backlight is completely turned off.
  • Page 19 InZennio Z41 Figure 11 Dynamic Distribution of the enabled boxes http://www.zennio.com Tecnical Support: http://zennioenglish.zendesk.com...

  • Page 20: Ets Parameterisation

    InZennio Z41 3 ETS PARAMETERISATION To begin with the parameterisation of InZennio Z41, once the ETS program is running it is necessary to import the product database (Z41 application program). Next, the device is added to the project and, after right-clicking on the name of the device, the option “Edit parameters”...
  • Page 21 InZennio Z41 [General] Date: 3-byte object for externally (for example, by linking it to a KNX clock) setting the internal date of the device. This object can also accept read requests, so the current date of the device can be checked. It is also automatically sent after date changes made by the user from the screen itself.

  • Page 22: Main Configuration

    InZennio Z41  Ethernet,  Energy monitor objects,  White-channel objects.  Firmware Update. Menu, which will contain one more screen by default:  Configuration, from which it will be possible to activate and configure each of the six general-purpose pages of the device (see section 2.2).

  • Page 23: General

    The General screen contains the following parameters: Power Supply Voltage: lets the integrator specify the particular voltage of the external supply powering Z41. The available values are 12 (by default), 24 and 29 volts. Selecting one option or another will only cause an internal correction over the temperature value measured by the built-in probe.
  • Page 24 InZennio Z41 Note: the default option is encouraged. Permanent illumination may affect adversely the device lifetime, and is only intended for special circumstances. Show Temperature: sets whether the current temperature should show or not in the upper right corner of every page, being necessary in such case to choose the source of the temperature value: “Internal temperature probe”...

  • Page 25: Security

    InZennio Z41 3.2.2 SECURITY Figure 15 Security (Main Configuration) This screen permits selecting how many security levels (one or two) will be available for the configuration of the access to the control pages. In other words, it permits setting one or two different passwords, so the integrator can afterwards configure whether the access to each page will be protected by one password or another, or remain unprotected –...
  • Page 26 InZennio Z41 cannot be used instead of password #2. This behaviour permits, therefore, making password #2 available to users with further privileges while password #1 is assigned to users with fewer privileges. The parameters on the Security screen are: Security Levels: dropdown list for selecting whether one (default option) or two security levels will be available.

  • Page 27: Touch Lock

    InZennio Z41 even if the device asks for password #1, the new password typed afterwards will be anyway stored as the new password for level 1. Security Pad Levels: parameter consisting in six additional textboxes, intended for the customisation of the messages that the device shows (or may show) when the user interacts with the password insertion dialog.
  • Page 28 InZennio Z41 This screen is provided for the configuration of the “welcome” and “touch lock” objects. By default two parameters are shown: Touch Locking: dropdown list with the following options: “0=Touch enabled; 1=Touch disabled” (default value) and “0=Touch disabled; 1=Touch enabled”.

  • Page 29: Internal Temperature Sensor

    InZennio Z41 3.2.4 INTERNAL TEMPERATURE SENSOR Figure 19 Internal Temperature Sensor (Main Configuration) This screen permits configuring the internal temperature sensor of the device. Three parameters are provided for this: Sensor Calibration: permits setting a certain correction over the values thrown by the internal temperature probe.

  • Page 30: Ethernet

    IP assignment through the DHCP protocol. The Ethernet interface in Z41 is also intended to let the integrator update the firmware of the device (see section 1.3.1) across a local network (alternatively, this process can be performed through the built-in USB interface).

  • Page 31: Energy Monitor Objects

    So, when any of the six channels is enabled, the four communication objects corresponding to that channel will show up. For further information about these objects and about power consumption monitoring in Z41, please refer to epigraph 0 in section 3.4.2.5. http://www.zennio.com Tecnical Support:...

  • Page 32: White-Channel Objects

    RGBW lighting dimmers. For further information about the usage of these objects and about the per-channel dimming controls implemented by Z41, please refer to epigraph b) in section 3.4.2.5. 3.2.8 FIRMWARE UPDATE Figure 23 Firmware Update This tab lets the integrator enable or disable, independently, the device firmware update function (see section 1.3.1) through the Ethernet or USB ports.

  • Page 33: Menu

    ETS by the integrator: Figure 24 Password-Protected Update Note: reading the specific user manual of the firmware update process available at the Zennio webpage is encouraged, as it contains particular remarks regarding the password protection. 3.3 MENU The Menu tab contains only one screen, Configuration.

  • Page 34: Page N

    InZennio Z41 The available parameters are: Title: text field that defines the title that will be shown on the top of the Menu page. Automatic Page Shaping: dropdown list that sets whether the boxes in the Menu page should be automatically distributed (option “Yes”) depending on the amount of functional boxes, or display as a static 2x4 grid (option “No”).

  • Page 35: Configuration

    See section 2.6. Icon: sets the icon that will represent the page in the Menu page. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com. Protected: dropdown list that permits setting whether the access to the page will be password protected or not.

  • Page 36: Box I

    InZennio Z41 Two levels:  No: no password protection for the page. All users can access it.  Level 1: the page will implement security level 1. To access it, users will be required to enter password 1 or password 2.

  • Page 37: Indicator

    Therefore, when the device receives the values “0” or “1” through the aforementioned object, the box will show one icon or another. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 38 InZennio Z41 Figure 30 Binary Indicator (Text) c) Enumerated Indicator (Icon) The box will behave analogously to the case of the Binary indicator (Icon) however it will be possible to distinguish up to 6 states (configurable through the # Enums parameter) instead of only two. The states will be determined by the reception of any values between 0 and 255, not only by values 0 and 1.
  • Page 39 InZennio Z41 d) Enumerated Indicator (Text) The box will behave analogously to the case of the Binary indicator (Text) however it will be possible to distinguish up to 6 states (configurable through the # Enums parameter) instead of only two. The states will be determined by the reception of any values between 0 and 255, not only by values 0 and 1.
  • Page 40 (Float Unit), empty by default, that permits specifying the measuring units (up to 6 characters) of the displayed value, for instance “ºC”. Moreover, for this particular case, Z41 will dynamically adjust the number of the decimal figures shown depending on the order of magnitude of the current value: two for values greater than 0 and lower than 0.1;...

  • Page 41: 1-Button Control

    InZennio Z41 The graph (where the vertical scale will dynamically adapt to the values being represented) shows the chronological evolution of the value, with higher or lower detail (hourly, daily, weekly, monthly; see Figure 36) depending on the zoom level set by the user by means of the on-screen magnifying glass control.
  • Page 42 Finally, the dropdown list next to Button (in the middle) permits selecting the icon to be displayed inside the button. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 43 Finally, the dropdown list next to Button (in the middle) permits selecting an icon to be displayed inside the button. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.

  • Page 44: 2-Button Control

    Left button and Right button, each containing a dropdown list for the selection of the desired icons to be displayed inside the buttons in the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 45 InZennio Z41 On the other hand, the Function parameter contains a dropdown list for the selection of the particular two-button control type to be implemented by the box. The available options (and their related parameters) are: a) Binary Control (Icon)
  • Page 46 InZennio Z41 When the user touches the buttons, a binary value will be sent through the [Pn][Bi] Binary Control object, while the status object, [Pn][Bi] Binary Indicator, will determine the text that will be shown in the box. The available parameters are: ...
  • Page 47 InZennio Z41  Value j: numerical value (0 – 255) that will be sent through the control object when the user, after pressing the buttons, sets the control box to state j. Icon j: indicative icon that will be displayed in the box when the status ...
  • Page 48 InZennio Z41 Text j: indicative text that will be displayed in the box when the status  object (which gets automatically updated whenever a control order is sent, although it may also receive values from the bus) acquires the numerical value defined in the above parameter.
  • Page 49 InZennio Z41 Figura 46 1-Byte (Unsigned Int.) 2-Button Control  Action: sets which of the two buttons will be increasing the current numerical value and which will be decreasing it on user presses. The permitted options are “Left Decrease, Right Increase” (default) and “Left increase, Right Decrease”.
  • Page 50 Last, the dropdown list under Button Icon sets the icon to be displayed by the buttons. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com. g) Shutter Control Shutter controls permit sending move up, move down, stop or step shutter orders to the KNX bus by pressing the buttons in the box.
  • Page 51 InZennio Z41 Figure 48 Shutter Control The only specific parameter for this function is:  Action: sets which of the two buttons will send the move up orders and which the move down orders. Options are “Left Down, Right Up” (default) and “Left Up, Right Down”.
  • Page 52 InZennio Z41 Figure 49 Lighting Control The available parameters are:  Action: sets which of the two buttons will send the “turn on” orders and which the “turn off” orders. Options are “Left Off, Right On” (default) and “Left On, Right Off”.

  • Page 53: Climate Control

    25% which is in fact interrupted if a stop order arrives (such order is sent by Z41 when the user releases the button). Due to this behaviour, it is advised to parameterise dimming steps of...
  • Page 54 InZennio Z41 automatically updated after sending control orders (that is, after pressing the buttons), being even possible to receive values from the bus, for example, from the corresponding setpoint status object from the external thermostat. Figure 50 Setpoint Therefore, after every press on the temperature increment button, the bus will...
  • Page 55 InZennio Z41 Figure 51 Absolute Setpoint Control If the second option is selected (1-bit object setpoint control), the control object will be binary, and it will throw a “0” to the bus whenever the user asks for a setpoint decrement, and a “1” when the user asks for an increment.
  • Page 56 Write flag enabled with the intention of permitting the reception of feedback from the thermostat, which may reset or modify the status of the offset for any reason at any time. This feedback allows that Z41 updates its own value to equal that from the external thermostat. Thinking of the above example, if Z41 receives the value “0”...
  • Page 57  Left Button and Right Button: permit selecting the desired icon to be displayed inside each button in the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 58 InZennio Z41 Two communication objects are also enabled: the [Pn][Bi] Mode Control control object and the [Pn][Bi] Mode Indicator status object. When the user activates the Cool mode, the device will send the value “0” through the control object, while on the activation of the Heat mode the value “1”...
  • Page 59 Finally, the Left Button and Right Button parameters permit selecting the icon that will be displayed inside the buttons of the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 60  Left Button and Right Button: permit selecting the icon that will be displayed inside the buttons of the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 61 InZennio Z41 d) Special Modes Figure 60 Special Modes (Box) Boxes configured as special mode controls include two buttons that let the user sequentially commute between the different special climate modes, as well as an icon indicator that will adopt an aspect or another depending on the currently active special mode.

  • Page 62: Other

     Left Button and Right Button: permit selecting the icon that will be displayed inside the buttons in the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 63  Left Button and Right Button: permit selecting the icon that will be displayed inside the buttons in the box. Note: the list with all the icons available in Z41 can be found in the document “Z41 Icon list”, downloadable from www.zennio.com.
  • Page 64 InZennio Z41  The button on the right, when pressed, launches a colour palette that permits the selection of a light level for every channel, either by touching on any of the pre-set colours, or by separately selecting the level of each channel (R, G, B).
  • Page 65 InZennio Z41 must have been specifically enabled from the White Channel Objects screen (see section 3.2.7) under the Main configuration tab, which will make the [RGBW] White Channel x available for sending dimming orders to the white channel. Important: although it is possible to assign the “RGBW control” function to any...
  • Page 66 Energy Monitor (KES) Figure 69 Energy Monitor (KES) This function permits making use of one of the boxes of Z41 as a monitor of information related to energy consumption –which may be reported by devices such as KES from Zennio– and in particular, as a monitor of the evolution of the instant power.
  • Page 67 When this function is assigned to the box, two 1-bit communication objects show up: [Pn][Bi] Energy Monitor: Request and [Pn][Bi] Energy Monitor: Reset. The first of them is intended for sending a request from Z41 to KES asking for the updated values of the energy measurement, which requires...
  • Page 68 InZennio Z41 Power). The horizontal axis will show different time lapses (hours, days, or months), depending on the selected zoom level. Instant Value of the Energy, CO and Cost objects: indicator that,  depending on whether the Energy consumption, CO2 and Cost...
  • Page 69 InZennio Z41 Timer type selector Time selector Value to be sent Figure 74 Daily Timer (Pop-Up Window) This window contains the following elements:  Timer Type Selector: two-button control that permits switching through the following options: Timer Timer active Timer active Timer active inactive.
  • Page 70 InZennio Z41 Note: in case of disabling a sending through [Pn][Bi] Daily Timer Enabling, the corresponding box will show the “forbidden” icon, although the box will not lose the configuration previously set by the user. Finally, this function offers the following parameters in ETS: ...
  • Page 71 InZennio Z41 Day selector Value to be sent (ON / OFF) Time selector Figure 77 Weekly Timer (Pop-Up Window). This window contains the following elements:  Day Selector: lets the user select the days on which the timed sending will take place.
  • Page 72 ([Pn][Bi] Alarm Trigger) that permits receiving alarm messages from the bus, thus making Z41 emit a continuous beep while the screen light blinks. In addition, the screen will automatically browse to the page containing the alarm box that has been triggered.
  • Page 73 This will let Z41 automatically assume the alarm situation if the “no alarm” value does not get sent through the trigger object after a certain time, for example upon failures of the transmitter.

  • Page 74: Profile Page

    “1”. If the object being sent is linked to the alarm trigger object from an alarm box in Z41 where periodic monitoring has been parameterised and where the value “1” is...

  • Page 75: Configuration

    InZennio Z41 3.5.1 CONFIGURATION This screen permits the integrator configure the controls that will be available for the final user within the Profile page (see section 2.3), as well as the label that will identify them on the screen. Note that the Profile page itself can be activated or hidden from the Configuration screen, under the Menu tab (see section 3.3.1).

  • Page 76: Thermostat N

    (parameter Title), a box shaping (parameter Automatic Page Shaping; see section 2.6), and a security level (parameter Protected; see section 3.2.2) can be set. For details on the Device Pairing function, please refer to ANNEX I. Controlling Z41 Remotely via IP.
  • Page 77 Under each of the tabs, a set of screens (Configuration, Setpoint, etc.) is provided to define the type of the thermostatic control the user will be performing from Z41. Note: for further information about the behaviour and the parameterisation of the Zennio “Building”...

  • Page 78: Annex I. Controlling Z41 Remotely Via Ip

    “General” tab (see section 3.2.5). Figure 84 Configuration page with Device Paring enabled. In addition, before being possible to remotely control Z41, it is first necessary to pair it to the remote application. This requires that the integrator also enables the Device Pairing parameter in the “Configuration”...

  • Page 79: Pairing Procedure

    Z41 with further remote applications in the future. It is also remarkable that disabling this icon is independent from disabling the remote...

  • Page 80: Remote Applications

    The user will be required to enter this key word on the remote application in order to set the link with Z41. Note that this process is only required once, so the mobile device can register the particular Z41.

  • Page 81: Annex Ii. Communication Objects

    InZennio Z41 ANNEX II. COMMUNICATION OBJECTS ”Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself.
  • Page 82 InZennio Z41 Number Size Flags Data Type (DPT) Functional range 1st boot P Reboot P Name Function disabled [General] Welcome Object 1-bit Generic Control 1 Bit C T R - - DPT_Switch [PX][BX] RGB Colour Red, Green and Blue C - - W U √...
  • Page 83 InZennio Z41 Number Size Flags Data Type (DPT) Functional range 1st boot P Reboot P Name Function Indicator 1 = Comfort [PX][BX] 2-byte Unsigned Int 0...65535 2 = Standby Indicator 1 Byte C - - W U DPT_HVACMode √ 3 = Economy...
  • Page 84 InZennio Z41 Number Size Flags Data Type (DPT) Functional range 1st boot P Reboot P Name Function [PX][BX] Light On/Off 0=Off; 1=On 1 Bit C T R - - DPT_Step [PX][BX] Move Shutter 0=Up; 1=Down 1 Bit C T R - - DPT_Heat_Cool [PX][BX] Enumerated Control 0...255...
  • Page 85 InZennio Z41 Number Size Flags Data Type (DPT) Functional range 1st boot P Reboot P Name Function [PX][BX] Light Dimming 4-bit Dimming Control 1 Byte C T R W U DPT_Scaling 0% - 100% [PX][BX] Stop Shutter 0 or 1 -> Stop...
  • Page 86 InZennio Z41 Number Size Flags Data Type (DPT) Functional range 1st boot P Reboot P Name Function [TX] Setpoint Reset Reset setpoint to default 1 Bit C - - W - DPT_Reset [TX] Mode 0 = Cool; 1 = Heat...
  • Page 87 Join and send us your inquiries about Zennio devices: http://zennioenglish.zendesk.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. Fax. +34 925 337 310. www.zennio.com info@zennio.com...

This manual is also suitable for:

Zn1vi-tp41c

Table of Contents