Dimensions; Torque Requirements; Assembly Instructions; Uncrate Mower - Exmark Lazer Z XS Operator's Manual

For Exmark Mower Parts Call 606-678-9623 or 606-561-4983

2.10 DIMENSIONS

2.10.1 Overall Width:
2.10.2 Overall Length:
2.10.3 Overall Height:
2.10.4 Tread Width: (center to center of tires, widthwise)
2.10.5 Wheel Base: (center of caster to center of drive tire)
2.10.6 Curb Weight:

2.11 TORQUE REQUIREMENTS

Bolt Location
Cutter Housing Spindle Nut ........................................ 140-145 ft-lbs. (190-197 N-m)
Blade Mounting Bolt.................................................... 115-120 ft-lbs. (156-163 N-M)
Engine Deck/Front Frame Mount Bolts............................... 30-35 ft-lbs. (41-47 N-M)
Anti-Scalp Roller Bolts ........................................................ 40-45 ft-lbs. (54-61 N-M)
Engine Mounting Bolts ....................................................... 30-35 ft-lbs. (41-47 N-M)
Wheel Lug Nuts .............................................................. 90-95 ft-lbs. (122-129 N-M)
Wheel Motor Mounting Bolts............................................. 72-77 ft-lbs. (98-104 N-M)
Wheel Hub Slotted Nut .............................................. minimum 125 ft-lbs. (169 N-M)
Rollover Protection System (Roll Bar) Mounting Bolts ....... 30-35 ft-lbs. (41-47 N-M)

3. ASSEMBLY INSTRUCTIONS

3.1 UNCRATE MOWER

3.2 INSTALL ROLLOVER PROTECTION SYSTEM (ROLL BAR)

3.2.1
3.2.2
without deck
60" Deck 54.5 in. (138.4 cm)
72" Deck 58.5 in. (148.6 cm)
Roll Bar – Up
60" Deck 82.2 in. (208.8 cm)
72" Deck 86.0 in. (218.4 cm)
Roll Bar - Up
60" Deck 73.7 in. (187.2 cm)
72" Deck 73.7 in. (187.2 cm)
Drive Wheels
60" Deck 42.8 in. (108.7 cm)
72" Deck 46.8 in. (118.9 cm)
60" Deck 54.0 in. (137.2 cm)
72" Deck 56.8 in. (144.3 cm)
60" Deck 1450 lbs. (658 kg)
72" Deck 1520 lbs. (689 kg)
Disassemble roll bar from the crate.
a) Remove roll bar tubes from sides of crate.
b) Remove the two brackets used to mount the bottom of the upper roll bar tube
to the crate. Remove the 1/2-13 x 3 1/4 capscrews and 1/2-13 hex flange
lock nuts from the two brackets at each end of the upper roll bar tube and
retain for later use.
Install the two lower roll bar tubes.
a) Locate the left and right lower roll bar tubes.
b) Align lower roll bar tubes along wheel motor channels as shown in Figure 2.
www.mymowerparts.com
deflector up
61.4 in. (156.0 cm)
73.2 in. (185.9 cm)
Roll Bar - Down
92.3 in. (234.4 cm)
96.1 in. (244.1 cm)
Roll Bar - Down
55.6 in. (141.2 cm)
55.6 in. (141.2 cm)
Casters
38.9 in. (98.8 cm)
47.6 in. (120.9 cm)
- 13 -
deflector down
72.2 in. (183.4 cm)
84.3 in. (214.1 cm)
Torque