Summary of Contents for Hobby-Lobby eRC F-18E Super Hornet 90mm EDF
Page 2
Hobby-Lobby is pleased to announce the eRC F-18E Super Hornet 90mm EDF that includes scale electric retractable landing gear with suspension, 360 degree thrust vectoring nozzles and working position lights. A great deal of the assembly is pre-done for you. This is a receiver ready jet that only requires some simple assembly and the installation of the flight batteries and programming of your radio equipment to be ready to fly.
Page 3
Before starting, use the contents list to take an inventory and make sure it is complete. If any parts are missing or are not of acceptable quality, contact Hobby-Lobby.com support at 1-866-WE-FLY-RC (1-866-933-5972) Contents List Fuselage Battery Hatch ...
Page 4
1. This manual will help you assemble your F-18E. Let’s start with the installation of the main wing panels. Apply an even coat of 5-minute epoxy to the slot for the carbon rod in the wing and fuselage and the root of the wing panel. 2.
Page 5
5. Plug in the servo connector and the wing tip light. Please match the polarity. On the servo connection, the orange wire matches with the white wire on the plug that exits the fuselage. 6. Feed the connected plugs into the fuselage and carefully push the wires into the slot in the wing and fuselage.
Page 6
9. Attach the elevator to the fuselage using the supplied wood screws. 10. Connect the elevator linkage and install the foam cover using a contact adhesive. 11. Install the nose cone using foam safe CA glue, 5-minute epoxy, or contact adhesive. 12.
Page 7
13. Use 5-minute epoxy to install the Vertical Fins. Be sure to push the light wires all the way into the fuselage so they do not interfere with the fit the Vertical Fins. 14. To install the drop tanks, push them into the matching tabs on the bottom of the wing.
Page 8
25. A 7-channel computer radio is required to fly the F-18E. The following instructions are for the Spektrum DX-7 transmitter with the Spektrum AR7000 receiver. Make sure your screen matches the photos. 26. From the INPUT SELECT screen, inhibit AUX2 and FLAP. 27.
Page 9
30. From the D/R & EXPO screen, select the AILE function. Set the dual rate switch for the ailerons to the “0” POSITION. Set the EXPO for +30 % to make the Ailerons less responsive in roll around the stick center. Set the D/R to 100%.
Page 10
34. From the D/R & EXPO screen, select the RUDD function. Set the dual rate switch for the elevator to the “0” POSITION. Set the EXPO for +20 % to make the rudder less responsive around the stick center. Set the D/R to 100%. 35.
Page 11
38. Select PROG.MIX4 from the radio menu. Set the mix for AILE to AUX2. Make sure that the rates are both at -100% and that the switch is set to ON. There should be no offset for this mix. 39. On LOW RATES the Ailerons should move 1/2"...
Page 12
42. On HIGH RATES the Elevators should move 3/4" in both directions. 43. The Center of Gravity (CG) is measured from where the leading edge of the wing meets the fuselage. The CG range is 2- 3/4” (70mm) to 3” (75mm). This is an all- around good CG location;...
Flying We recommend that takeoffs and landings be made on LOW RATES. Initial flights should be made using LOW RATES until you are familiar with the aircraft. LOW RATES allow you to fly smooth pattern maneuvers. The jet is very stable with solid handling. On HIGH RATES with the Thrust Vectoring turned on, the airplane can perform amazing maneuvers.
Page 14
In no event shall Hobby-Lobby’s liability exceed the original cost of the purchased kit. Completely read through this manual before starting construction. Hobby Lobby International, Inc. 5614 Franklin Pike Circle Brentwood, TN 37027...
Need help?
Do you have a question about the eRC F-18E Super Hornet 90mm EDF and is the answer not in the manual?
Questions and answers